Date: Thu, 4 Jan 2001 12:50:22 -0600 (CST)
From: Simon Epsteyn <seva@fnal.gov>
To: Warner Losh <imp@bsdimp.com>
Cc: freebsd-mobile@FreeBSD.ORG, Bill Paul <wpaul@ee.columbia.edu>
Subject: Re: AiroNet 'No card in database for "(null)"("(null)")' problem (4.2-STABLE)
Message-ID: <Pine.LNX.4.10.10101041216310.516-300000@null.cc.uic.edu>
In-Reply-To: <200101040558.f045wU119690@harmony.village.org>
next in thread | previous in thread | raw e-mail | index | archive | help
[-- Attachment #1 --] Warner, > Classig memory conflict. But other cards (Adaptec SCSI) do work? There are 2 memory addresses that are are configured, one during kernel build in the kernel config, and another for pcccardd. Are they supposed to be the same? > : pcic0: <Intel i82365> at port 0x3e0 iomem 0xd0000 irq 10 on isa0 > > You need to use 0xd4000 or 0xd8000 for this. I have tried both 0xd4000 and 0xd8000 for kernel and pccardd and I get same results. For more info I am including (last) full dmesg output and (current) kernel config. > : I've tried "pccardc pccardmem 0xe0000" as well... > > 0xe0000 is usually the BIOS. This is what Bill Paul suggests to try at http://people.freebsd.org/~wpaul/Aironet/ regarding 3.x-STABLE: ... Note: you may beed to change the pccard_mem setting. This setting describes the base of a shared memory window used to read data (such as the CIS data for PCMCIA cards) from the PCMCIA controller. The default address is 0xd0000, and this seems to work for most laptops. In some rare cases however, you may need to specify an alternate memory window. If pccardd reports an error to /var/log/messages about an unknown device with the name ""/"" and you're sure the vpp voltages are being set properly, then you will probably need to use another address. To test an alternate address, such as 0xe0000, you can do the following: # pccardc pccardmem 0xe0000 # pccardc dumpcis ... I've checked the code and the vpp voltage is being set correctly to 5V /Simon [-- Attachment #2 --] Copyright (c) 1992-2001 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.2-STABLE #11: Thu Jan 4 12:33:15 CST 2001 root@einsof:/usr/src/sys/compile/EINSOF Timecounter "i8254" frequency 1193182 Hz CPU: Pentium II/Pentium II Xeon/Celeron (364.74-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x66a Stepping = 10 Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR> real memory = 67043328 (65472K bytes) avail memory = 61784064 (60336K bytes) Preloaded elf kernel "kernel" at 0xc0363000. Preloaded userconfig_script "/boot/kernel.conf" at 0xc036309c. Pentium Pro MTRR support enabled md0: Malloc disk apm0: <APM BIOS> on motherboard apm: found APM BIOS v1.2, connected at v1.2 npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Intel 82443BX host to PCI bridge (AGP disabled)> on motherboard pci0: <PCI bus> on pcib0 fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xfcc0-0xfcff mem 0xfec00000-0xfecfffff,0xfedef000-0xfedeffff irq 9 at device 6.0 on pci0 fxp0: Ethernet address 08:00:46:08:46:c6 isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 ATA33 controller> port 0xfc90-0xfc9f at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xfca0-0xfcbf irq 9 at device 7.2 on pci0 usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered chip1: <Intel 82371AB Power management controller> port 0x2180-0x218f at device 7.3 on pci0 pci0: <NeoMagic MagicMedia 256AV SVGA controller> at 8.0 irq 9 pcm0: <NeoMagic 256AV> mem 0xfea00000-0xfeafffff,0xfe000000-0xfe3fffff irq 9 at device 8.1 on pci0 chip2: <Sony CXD1847A FireWire Host Controller> mem 0xfedeec00-0xfedeedff irq 9 at device 9.0 on pci0 pcic-pci0: <Ricoh RL5C475 PCI-CardBus Bridge> at device 10.0 on pci0 pci0: <unknown card> (vendor=0x127a, dev=0x2005) at 11.0 irq 9 fdc0: direction bit not set fdc0: cmd 3 failed at out byte 1 of 3 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model GlidePoint, device ID 0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> pcic0: <Intel i82365> at port 0x3e0 iomem 0xd8000 irq 10 on isa0 pcic0: management irq 10 pccard0: <PC Card bus -- kludge version> on pcic0 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold ppi0: <Parallel I/O> on ppbus0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ata1-slave: ata_command: timeout waiting for intr ata1-slave: identify failed ad0: 6194MB <IBM-DBCA-206480> [13424/15/63] at ata0-master UDMA33 ad2: 7MB <MEMORYSTICK 8M 8K> [495/2/16] at ata1-master PIO1 Mounting root from ufs:/dev/ad0s3a pccard: card inserted, slot 0 pccard: card removed, slot 0 [-- Attachment #3 --] # # GENERIC -- Generic kernel configuration file for FreeBSD/i386 # # For more information on this file, please read the handbook section on # Kernel Configuration Files: # # http://www.FreeBSD.org/handbook/kernelconfig-config.html # # The handbook is also available locally in /usr/share/doc/handbook # if you've installed the doc distribution, otherwise always see the # FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the # latest information. # # An exhaustive list of options and more detailed explanations of the # device lines is also present in the ./LINT configuration file. If you are # in doubt as to the purpose or necessity of a line, check first in LINT. # # $FreeBSD: src/sys/i386/conf/GENERIC,v 1.246.2.20 2000/10/31 23:16:07 n_hibma Exp $ machine i386 #cpu I386_CPU #cpu I486_CPU cpu I586_CPU cpu I686_CPU ident EINSOF maxusers 64 #makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols #options MATH_EMULATE #Support for x87 emulation options INET #InterNETworking #options INET6 #IPv6 communications protocols options FFS #Berkeley Fast Filesystem options FFS_ROOT #FFS usable as root device [keep this!] options SOFTUPDATES #Enable FFS soft updates support options MFS #Memory Filesystem options MD_ROOT #MD is a potential root device options NFS #Network Filesystem options NFS_ROOT #NFS usable as root device, NFS required options MSDOSFS #MSDOS Filesystem options CD9660 #ISO 9660 Filesystem options CD9660_ROOT #CD-ROM usable as root, CD9660 required options PROCFS #Process filesystem options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!] options SCSI_DELAY=5000 #Delay (in ms) before probing SCSI options UCONSOLE #Allow users to grab the console options USERCONFIG #boot -c editor options VISUAL_USERCONFIG #visual boot -c editor options KTRACE #ktrace(1) support options SYSVSHM #SYSV-style shared memory options SYSVMSG #SYSV-style message queues options SYSVSEM #SYSV-style semaphores options P1003_1B #Posix P1003_1B real-time extensions options _KPOSIX_PRIORITY_SCHEDULING options ICMP_BANDLIM #Rate limit bad replies options KBD_INSTALL_CDEV # install a CDEV entry in /dev # To make an SMP kernel, the next two are needed #options SMP # Symmetric MultiProcessor Kernel #options APIC_IO # Symmetric (APIC) I/O # This allows you to actually store this configuration file into # the kernel binary itself, where it may be later read by saying: # strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL # options INCLUDE_CONFIG_FILE # Include this file in kernel device isa #device eisa device pci # Floppy drives device fdc0 at isa? port IO_FD1 irq 6 drq 2 device fd0 at fdc0 drive 0 #device fd1 at fdc0 drive 1 # ATA and ATAPI devices device ata0 at isa? port IO_WD1 irq 14 #device ata1 at isa? port IO_WD2 irq 15 device ata device atadisk # ATA disk drives device atapicd # ATAPI CDROM drives #device atapifd # ATAPI floppy drives #device atapist # ATAPI tape drives options ATA_STATIC_ID #Static device numbering options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI devices options IDE_DELAY=8000 # SCSI Controllers #device ahb # EISA AHA1742 family #device ahc # AHA2940 and onboard AIC7xxx devices #device amd # AMD 53C974 (Teckram DC-390(T)) #device isp # Qlogic family #device ncr # NCR/Symbios Logic #device sym # NCR/Symbios Logic (newer chipsets) #options SYM_SETUP_LP_PROBE_MAP=0x40 # Allow ncr to attach legacy NCR devices when # both sym and ncr are configured #device adv0 at isa? #device adw #device bt0 at isa? #device aha0 at isa? device aic0 #device ncv # NCR 53C500 #device nsp # Workbit Ninja SCSI-3 #device stg # TMC 18C30/18C50 # SCSI peripherals device scbus # SCSI bus (required) device da # Direct Access (disks) device sa # Sequential Access (tape etc) device cd # CD device pass # Passthrough device (direct SCSI access) # RAID controllers interfaced to the SCSI subsystem #device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID #device dpt # DPT Smartcache - See LINT for options! #device mly # Mylex AcceleRAID/eXtremeRAID # RAID controllers #device ida # Compaq Smart RAID #device amr # AMI MegaRAID #device mlx # Mylex DAC960 family #device twe # 3ware Escalade # atkbdc0 controls both the keyboard and the PS/2 mouse device atkbdc0 at isa? port IO_KBD device atkbd0 at atkbdc? irq 1 flags 0x1 device psm0 at atkbdc? irq 12 device vga0 at isa? # splash screen/screen saver pseudo-device splash # syscons is the default console driver, resembling an SCO console device sc0 at isa? flags 0x100 options SC_ALT_MOUSE_IMAGE options SC_TWOBUTTON_MOUSE # Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver #device vt0 at isa? #options XSERVER # support for X server on a vt console #options FAT_CURSOR # start with block cursor # If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines #options PCVT_SCANSET=2 # IBM keyboards are non-std # Floating point support - do not disable. device npx0 at nexus? port IO_NPX irq 13 # Power management support (see LINT for more options) device apm0 at nexus? flags 0x20 # Advanced Power Management # PCCARD (PCMCIA) support device card device pcic0 at isa? irq 10 port 0x3e0 iomem 0xd8000 #device pcic1 at isa? irq 0 port 0x3e2 iomem 0xd4000 disable options PCIC_RESUME_RESET # Serial (COM) ports device sio0 at isa? port IO_COM1 flags 0x10 irq 4 #device sio1 at isa? port IO_COM2 irq 3 #device sio2 at isa? disable port IO_COM3 irq 5 #device sio3 at isa? disable port IO_COM4 irq 9 # Parallel port device ppc0 at isa? irq 7 device ppbus # Parallel port bus (required) device lpt # Printer device plip # TCP/IP over parallel device ppi # Parallel port interface device #device vpo # Requires scbus and da # PCI Ethernet NICs. #device de # DEC/Intel DC21x4x (``Tulip'') device fxp # Intel EtherExpress PRO/100B (82557, 82558) #device tx # SMC 9432TX (83c170 ``EPIC'') #device vx # 3Com 3c590, 3c595 (``Vortex'') #device wx # Intel Gigabit Ethernet Card (``Wiseman'') # PCI Ethernet NICs that use the common MII bus controller code. # NOTE: Be sure to keep the 'device miibus' line in order to use these NICs! #device miibus # MII bus support #device dc # DEC/Intel 21143 and various workalikes #device pcn # AMD Am79C79x PCI 10/100 NICs #device rl # RealTek 8129/8139 #device sf # Adaptec AIC-6915 (``Starfire'') #device sis # Silicon Integrated Systems SiS 900/SiS 7016 #device ste # Sundance ST201 (D-Link DFE-550TX) #device tl # Texas Instruments ThunderLAN #device vr # VIA Rhine, Rhine II #device wb # Winbond W89C840F #device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'') # ISA Ethernet NICs. #device ed0 at isa? port 0x280 irq 10 iomem 0xd8000 #device ex #device ep #device fe0 at isa? port 0x300 # WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really # exists only as a PCMCIA device, so there is no ISA attatement needed # and resources will always be dynamically assigned by the pccard code. #device wi # Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will # work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP # mode (the factory default). If you set the switches on your ISA # card for a manually chosen I/O address and IRQ, you must specify # those paremeters here. device an # Xircom Ethernet #device xe # The probe order of these is presently determined by i386/isa/isa_compat.c. #device ie0 at isa? port 0x300 irq 10 iomem 0xd0000 #device le0 at isa? port 0x300 irq 5 iomem 0xd0000 #device lnc0 at isa? port 0x280 irq 10 drq 0 #device cs0 at isa? port 0x300 #device sn0 at isa? port 0x300 irq 10 # Pseudo devices - the number indicates how many units to allocated. pseudo-device loop # Network loopback pseudo-device ether # Ethernet support pseudo-device sl 1 # Kernel SLIP pseudo-device ppp 1 # Kernel PPP pseudo-device tun # Packet tunnel. pseudo-device pty # Pseudo-ttys (telnet etc) pseudo-device md # Memory "disks" #pseudo-device gif 4 # IPv6 and IPv4 tunneling #pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation) # The `bpf' pseudo-device enables the Berkeley Packet Filter. # Be aware of the administrative consequences of enabling this! pseudo-device bpf 4 #Berkeley packet filter # USB support device uhci # UHCI PCI->USB interface #device ohci # OHCI PCI->USB interface device usb # USB Bus (required) device ugen # Generic device uhid # "Human Interface Devices" device ukbd # Keyboard device ulpt # Printer device umass # Disks/Mass storage - Requires scbus and da device ums # Mouse #device uscanner # Scanners # USB Ethernet, requires mii #device aue # ADMtek USB ethernet #device cue # CATC USB ethernet #device kue # Kawasaki LSI USB ethernet # Sound support device pcm
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.LNX.4.10.10101041216310.516-300000>