Date: Fri, 20 Dec 2019 15:36:28 +0000 From: bugzilla-noreply@freebsd.org To: bugs@FreeBSD.org Subject: [Bug 242008] Installation on BananaPi fails: mmc0: Failed to set VCCQ for card at relative address 1 Message-ID: <bug-242008-227-3GFGkdx9vA@https.bugs.freebsd.org/bugzilla/> In-Reply-To: <bug-242008-227@https.bugs.freebsd.org/bugzilla/> References: <bug-242008-227@https.bugs.freebsd.org/bugzilla/>
next in thread | previous in thread | raw e-mail | index | archive | help
https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=3D242008 --- Comment #2 from Helmut <helmut.schlattl@web.de> --- I booted FreeBSD-12.1 verbosely and with kern.smp.disabled=3D1 and got the following output in the serial console: usbus0: 480Mbps High Speed USB v2.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 480Mbps High Speed USB v2.0 usbus3: 12Mbps Full Speed USB v1.0 axp2xx_pmu0: Powered by AC aw_mmc0: Powering up sd/mmc mmc0: Probing bus ugen0.1: <Allwinner EHCI root HUB> at usbus0 uhub0: <Allwinner EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 ugen1.1: <Generic OHCI root HUB> at usbus1 uhub1: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 ugen2.1: <Allwinner EHCI root HUB> at usbus2 uhub2: <Allwinner EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2 ugen3.1: <Generic OHCI root HUB> at usbus3 uhub3: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3 mmc0: SD 2.0 interface conditions: OK mmc0: SD probe: OK (OCR: 0x00ff8000) mmc0: Current OCR: 0x00ff8000 mmc0: Probing cards mmc0: New card detected (CID 2842454e4434474221562a275e0107e7) mmc0: New card detected (CSD 400e00325b5900001ddd7f800a4000e9) mmc0: Card at relative address 0x59b4 added: mmc0: card: SDHC ND4GB 2.1 SN 562A275E MFG 07/2016 by 40 BE mmc0: quirks: 0 mmc0: bus: 4bit, 50MHz (high speed timing) mmc0: memory: 7829504 blocks, erase sector 8192 blocks mmc0: setting transfer rate to 50.000MHz (high speed timing) mmcsd0: 4GB <SDHC ND4GB 2.1 SN 562A275E MFG 07/2016 by 40 BE> at mmc0 50.0MHz/4bit/32768-block regulator: shutting down vcc3v0 regulator: shutting down vcc3v3 regulator: shutting down vcc5v0 regulator: shutting down ldo3 Trying to mount root from ufs:/dev/ufs/rootfs [rw]... GEOM: new disk mmcsd0 mmc0: setting bus width to 4 bits high speed timing mmc0: Failed to set VCCQ for card at relative address 22964 GEOM_PART: partition 1 on (mmcsd0, MBR) is not aligned on 4194304 bytes GEOM_PART: partition 2 on (mmcsd0, MBR) is not aligned on 4194304 bytes aw_mmc0: error rint: --=20 You are receiving this mail because: You are the assignee for the bug.=
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?bug-242008-227-3GFGkdx9vA>