Date: Mon, 19 Jul 1999 11:31:37 +0200 (MET DST) From: HEIN Martin <heinm@maxdev.maxmobil.at> To: freebsd-isdn@freebsd.org Subject: FreeBSD 3.1 + i4b 0.82.0 Message-ID: <Pine.GSO.4.10.9907191130550.8716-100000@maxdev.maxmobil.at>
next in thread | raw e-mail | index | archive | help
Hi everybody,
Since I did an upgrade to i4b 0.82.0, I always receive an error message
as described below:
FreeBSD promaeteus.madmax 3.1-RELEASE FreeBSD 3.1-RELEASE #6: Fri
Jul 16 11:39:20 CEST 1999
root@promaeteus.madmax:/usr/src/sys/compile/PROMAETEUS i386
------------------------------------------------------------
configuring I4BISDN/PPP-interface isp0 to EUnet
ifconfig: ioctl (SIOCAIFADDR): File exists
spppcontrol: SIOCGIFGENERIC(SPPPIOGDEFS): Bad address
configuring I4BISDN/PPP-interface isp1 to EUnet
ifconfig: ioctl (SIOCAIFADDR): File exists
spppcontrol: SIOCGIFGENERIC(SPPPIOGDEFS): Bad address
starting the isdn4bsd ISDN management daemon ...
adding default route to isp0
route: writing to routing socket: File exists
add net default: gateway isp0: File exists
------------------------------------------------------------
Copyright (c) 1992-1999 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights
reserved.
FreeBSD 3.1-RELEASE #6: Fri Jul 16 11:39:20 CEST 1999
root@promaeteus.madmax:/usr/src/sys/compile/PROMAETEUS
Timecounter "i8254" frequency 1193182 Hz
CPU: i486 DX4 (486-class CPU)
Origin = "GenuineIntel" Id = 0x480 Stepping=0
Features=0x3<FPU,VME>
real memory = 33554432 (32768K bytes)
avail memory = 29601792 (28908K bytes)
Preloaded elf kernel "kernel" at 0xf032e000.
Probing for devices on PCI bus 0:
chip0: <SiS 85c496> rev 0x01 on pci0.5.0
ed1: <NE2000 PCI Ethernet (ProLAN)> rev 0x00 int a irq 9 on
pci0.10.0
ed1: address 00:40:95:04:b6:3b, type NE2000 (16 bit)
vga0: <Trident model 9440 VGA-compatible display device> rev 0xe3
int a irq 11 on pci0.11.0
ncr0: <ncr 53c810a fast10 scsi> rev 0x23 int a irq 15 on pci0.12.0
Probing for PnP devices:
Probing for devices on the ISA bus:
sc0 on isa
sc0: VGA color <16 virtual consoles, flags=0x0>
atkbdc0 at 0x60-0x6f on motherboard
atkbd0 irq 1 on isa
sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: FIFO enabled, 8 bytes threshold
fd0: 1.44MB 3.5in
wt0 at 0x370-0x371 irq 9 drq 1 on isa
wt0: type <Wangtek>
isic0 at 0x268 irq 5 flags 0x7 on isa
isic0: USRobotics Sportster ISDN TA intern
isic0: ISAC 2085 Version A1/A2 or 2086/2186 Version 1.1 (IOM-2)
(Addr=0xc268)
isic0: HSCX 82525 or 21525 Version 2.1 (AddrA=0x268, AddrB=0x4268)
ppc0 at 0x278 irq 7 on isa
ppc0: SMC FDC37C665GT chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE
mode
ppc0: FIFO with 16/16/15 bytes threshold
nlpt0: <generic printer> on ppbus 0
nlpt0: Interrupt-driven port
ppi0: <generic parallel i/o> on ppbus 0
plip0: <PLIP network interface> on ppbus 0
npx0 on motherboard
npx0: INT 16 interface
vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
IP packet filtering initialized, divert enabled, rule-based
forwarding enabled, logging limited to 100 packets/entry
i4b: ISDN call control device attached
i4bisppp: 4 ISDN SyncPPP device(s) attached
i4bctl: ISDN system control port attached
i4bipr: 4 IP over raw HDLC ISDN device(s) attached (VJ header
compression)
i4btel: 2 ISDN telephony interface device(s) attached
i4brbch: 4 raw B channel access device(s) attached
i4btrc: 4 ISDN trace device(s) attached
BRIDGE 981214, have 59 interfaces
-- index 1 ed1 type 6 phy 0 addrl 6 addr 00.40.95.04.b6.3b
DUMMYNET initialized (980901) -- size dn_pkt 48
IP Filter: initialized. Default = pass all, Logging = enabled
Waiting 15 seconds for SCSI devices to settle
da0 at ncr0 bus 0 target 0 lun 0
da0: <SEAGATE ST1480 5129> Fixed Direct Access SCSI-2 device
da0: 5.0MB/s transfers (5.0MHz, offset 8), Tagged Queueing Enabled
da0: 406MB (832527 512 byte sectors: 64H 32S/T 406C)
changing root device to da0s1a
cd0 at ncr0 bus 0 target 6 lun 0
cd0: <SONY CD-ROM CDU-8012 3.1e> Removable CD-ROM SCSI-2 device
cd0: 3.300MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not
present
(da0:ncr0:0:0:0): tagged openings now 16
ed1: promiscuous mode enabled
===> isp0: lcp close(initial)
===> rtinit: wrong ifa (0xf062ef00) was (0xf05ed000)
===> isp1: lcp close(initial)
isp0: lcp close(initial)
isp0: lcp close(initial)
isp0: lcp close(initial)
isp0: lcp close(initial)
Any ideas?
Martin
------------------------------------------------------------------------
Martin HEIN/max.it Voice: +43-676-3456-337
max.mobil. Telekommunikation Service GmbH FAX: +43-1-79585-6584
Kelsenstrasse 5-7 EMail: Martin.HEIN@maxmobil.at
A - 1030 Vienna/Austria/Europe WWW: http://www.maxmobil.at
========================================================================
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-isdn" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.GSO.4.10.9907191130550.8716-100000>