Date: Sat, 20 Jan 2001 23:41:41 -0500 From: The Babbler <bts@babbleon.org> To: MIHIRA Yoshiro <sanpei@sanpei.org> Cc: freebsd-mobile@freebsd.org, Greg Smith <gregsmith59@hotmail.com>, Pat Wendorf <beholder@unios.dhs.org> Subject: Re: Linksys 10/100 + 56K Modem PC Card (ethernet only) Message-ID: <3A6A6885.AE625005@babbleon.org> References: <200101200819.f0K8Jvr03803@lavender.sanpei.org>
next in thread | previous in thread | raw e-mail | index | archive | help
Ok, thank you for the assistance. Per Greg Smith's advice, I set boot -v, and this produced messages which reminded me that I didn't re-compile the kernel (as I had to do to get another Linksys card on a another FreeBSD laptop) to get rid of the spurious "ed1" parameters. But it still doesn't work. I checked the address/port ranges dumped by boot -v, but they don't seem to conflict with 0x2f8-2ff or 300-31f. Per Mihra Yoshiro's advice, I try the "auto" slot and the "?" IRQ. But it still doesn't work. (Same message as with slot 3.) Next I shall try the config 0x3 ed0 ? 0x8000 trick from Pat Wendorf. I don't hold out high hopes, but it's worth a try. Pat Wendorf: - How did you determine tthat 8000 was correct, and - How did you know that you could put the address there? My purusal of the man page showed that it took IRQs but not ioaddrs. Was I mis-reading it? Thanks for everybody's help . . . MIHIRA Yoshiro wrote: > > bts@babbleon.org wrote: > > >> I'm trying to get the a PCCARD working; specifically the card in the > >> title above. Although it's a modem/ethernet card, I now have a cable > >> modem so I only care about the ethernet aspect of the card. It works > >> fine under Linux, which has this view of it: > >> > >> eth0: NE2000 Compatible: io 0x300, irq 3, hw_addr 00:E0:98:70:F9:6A > >> > >> > >> For for FreeBSD, it's not known to the pccard data base. I've tried > >> creating a simple entry for it, but I'm not having much luck. Here's my > >> current pccard.conf entry for it: > >> > >> # This is the Linksys card I have, with the fat holder. > >> card "Linksys" "EtherFast 10&100 + 56K PC Card (PCMLM56)" > >> config 0x3 "ed" 3 > >> insert /etc/pccard_ether $device start > >> remove /etc/pccard_ether $device stop > > What version of FreeBSD did you use? 4.1-RELEASE or 4.2-RELEASE ? > > If you use 4.2-RELEASE or later, please try below configuration. > > # This is the Linksys card I have, with the fat holder. > card "Linksys" "EtherFast 10&100 + 56K PC Card (PCMLM56)" > config auto "ed" ? > insert /etc/pccard_ether $device start > remove /etc/pccard_ether $device stop > > Cheers. > MIHIRA Yoshiro > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-mobile" in the body of the message -- "Brian, the man from babble-on" bts@babbleon.org Brian T. Schellenberger http://www.babbleon.org Support http://www.eff.org. Support decss defendents. Support http://www.programming-freedom.org. Boycott amazon.com. To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3A6A6885.AE625005>