Date: Fri, 27 Feb 2004 00:54:16 +0800 From: Stephen Liu <satimis@icare.com.hk> To: Barbish3@adelphia.net Cc: freebsd-questions@freebsd.org Subject: Re: Connecting ISP problem Message-ID: <403E24B8.8020009@icare.com.hk> In-Reply-To: <MIEPLLIBMLEEABPDBIEGOEJPFMAA.Barbish3@adelphia.net> References: <MIEPLLIBMLEEABPDBIEGOEJPFMAA.Barbish3@adelphia.net>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi JJB,
Tks for your advice.
>This is wrong.
>++++++++++++++++ is not comment or command remove it.
>You have all statements starting in position 1 this is
>wrong, section header names start in position 1 and end with :
>
>default: and dialisp:
>
>
>make ppp.conf look like this
>default: & dialisp: start in position 1 and
>everything else starts in position 2
>delete all the other stuff you have in your ppp.conf.
>
>default:
> set log Phase tun #use to avoid excessive log sizes
> set timeout 0 # no idle time out, will not disconnect
>
>dialisp:
> set device PPPoE:rl0 # replace xxx with your Nic device
>name
> set authname YOURLOGINNAME # Replace with your ISP account IP
> set authkey YOURPASSWORD # Replace with your ISP account PW
> add default HISADDR # Add a (sticky) default route Mandatory
> enable dns # Gets the ISP's DNS IP address & places them
> # in resolv.conf for reference by FBSD box
>
>
>In rc.conf you have
>ifconfig-rl0=up
>
>and it should be
>
>ifconfig_rl0=up
>
>hostname="localhost" is wrong it needs to be FQDN
>as in hostname="fbsdstephenliu.com.hk"
>
>check /etc/syslog.conf and make sure ppp.log is enabled.
>Empty ppp.log before test and
>post ppp.log if this does not work.
>
Now ISP connected but failure to connect Internet. Tried twice
# ifconfig
rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet6 fe80::250:fcff:fe61:f394%rl0 prefixlen 64 scopeid 0x1
inet 192.168.2.2 netmask 0xffffff00 broadcast 192.168.2.255
ether 00:50:fc:61:f3:94
media: Ethernet autoselect (10baseT/UTP)
status: active
rl1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
ether 00:50:fc:6c:70:f7
media: Ethernet autoselect (10baseT/UTP)
status: no carrier
plip0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1492
inet 203.88.164.90 --> 203.88.164.1 netmask 0xffffffff
Opened by PID 236
# ping -c 3 [url]www.google.com[/url]
ping: cannot resolve [url]www.google.com:[/url] Host name lookup failure.
Tried follows without success;
# /sbin/route add default gw 203.88.164.1 dev tun0
# /sbin/route add default gw 203.88.164.1 dev ppp0
# /sbin/route add default gw 203.88.164.1 dev pppoe
all hanged on screen
# cat /var/log/ppp.log
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: Received
NGM_PPPOE_ACNAME (hook "TSW3-2-RX")
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: Received
NGM_PPPOE_SESSIONID
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: Received NGM_PPPOE_SUCCESS
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: deflink: carrier -> login
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: deflink: login -> lcp
Feb 27 07:56:39 localhost ppp[236]: tun0: Warning: deflink: Reducing
configured MRU from 1500 to 1492
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: bundle: Authenticate
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: deflink: his = PAP,
mine = none
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: Pap Output:
[email]satimis@icare.com.hk[/email] ********
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: Pap Input: SUCCESS ()
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: deflink: lcp -> open
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: bundle: Network
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: deflink: IPV6CP
protocol reject closes IPV6CP !
Feb 27 08:05:30 localhost ppp[236]: tun0: Phase: Received
NGM_PPPOE_ACNAME (hook "TSW3-2-RX")
Feb 27 08:05:30 localhost ppp[236]: tun0: Phase: Received
NGM_PPPOE_SESSIONID
Feb 27 08:05:30 localhost ppp[236]: tun0: Phase: Received NGM_PPPOE_SUCCESS
Feb 27 08:05:30 localhost ppp[236]: tun0: Phase: deflink: carrier -> login
Feb 27 08:05:30 localhost ppp[236]: tun0: Phase: deflink: login -> lcp
Feb 27 08:05:30 localhost ppp[236]: tun0: Warning: deflink: Reducing
configured MRU from 1500 to 1492
Feb 27 08:05:31 localhost ppp[236]: tun0: Phase: bundle: Authenticate
Feb 27 08:05:31 localhost ppp[236]: tun0: Phase: deflink: his = PAP,
mine = none
Feb 27 08:05:31 localhost ppp[236]: tun0: Phase: Pap Output:
[email]satimis@icare.com.hk[/email] ********
Feb 27 08:05:31 localhost ppp[236]: tun0: Phase: Pap Input: SUCCESS ()
Feb 27 08:05:31 localhost ppp[236]: tun0: Phase: deflink: lcp -> open
Feb 27 08:05:31 localhost ppp[236]: tun0: Phase: bundle: Network
Feb 27 08:05:31 localhost ppp[236]: tun0: Phase: deflink: IPV6CP
protocol reject closes IPV6CP !
# cat /etc/rc.conf
inetd_enable="YES"
keymap="us.pc-ctrl"
linux_enable="YES"
sshd_enable="YES"
usbd_enable="YES"
ifconfig_rl0="up"
ifconfig_rl0="DHCP"
# ppp_enable="YES"
# Activate user ppp auto-start at boot time
ppp_enable="YES" # Start User ppp task
ppp_mode="ddial" # ddial, auto, background
ppp_profile="dialisp": # Section in ppp.conf to exec
# cat /etc/ppp/ppp.conf
[code]
default:
set log phase tun
set timeout 0
dialisp::
set device pppoe:rl0
set authname [email]satimis@icare.com.hk[/email]
set authkey msliu20h
add default HISADDR
# (mandatory)
enable dns
'dialisp::' is correct
'dialisp:' complained as follow;
dialisp:: Configuration lable not found
B.R.
Stephen
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?403E24B8.8020009>