Date: Thu, 12 Nov 1998 14:31:24 +0300 (MSK) From: "Sergey V.Dorokhov" <svd@kbtelecom.nalnet.ru> To: freebsd-bugs@FreeBSD.ORG Subject: xl ethernet driver bug Message-ID: <199811121131.OAA24109@kbtelecom.nalnet.ru>
next in thread | raw e-mail | index | archive | help
Hello ! I have "3Com 3c905 Fast Etherlink XL 10/100BaseTX" ethernet card. Under 3.0-980520-SNAP this card worked with 'vx0' driver. Now it work with a new driver xl0 (which uses bus master DMA). But really it work unstable. From time to time xl driver output error message and computer lose link to other computers. Commands 'ifconfig xl0 down; ifconfig xl0 up' fix trouble for short time but then kernel output message 'panic....' and computer reboot. I send you file '/var/log/messages'. Can you fix this trouble? Thanks, Sergey Dorokhov. p.s. Motherboard ASUS P2L97, P][-233Mhz Copyright (c) 1992-1998 FreeBSD Inc. Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. FreeBSD 3.0-RELEASE #6: Fri Nov 6 20:55:57 MSK 1998 svd@shelob.nalchik.su:/usr/src/sys/compile/SHELOB Timecounter "i8254" frequency 1193182 Hz cost 3188 ns Timecounter "TSC" frequency 233864698 Hz cost 206 ns CPU: Pentium II (233.86-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x633 Stepping=3 Features=0x80f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,MMX> real memory = 134217728 (131072K bytes) avail memory = 128122880 (125120K bytes) Probing for devices on PCI bus 0: chip0: <Host to PCI bridge (vendor=8086 device=7180)> rev 0x03 on pci0.0.0 chip1: <PCI to PCI bridge (vendor=8086 device=7181)> rev 0x03 on pci0.1.0 chip2: <Intel 82371AB PCI to ISA bridge> rev 0x01 on pci0.4.0 chip3: <Intel 82371AB USB host controller> rev 0x01 int d irq 255 on pci0.4.2 chip4: <Intel 82371AB Power management controller> rev 0x01 on pci0.4.3 xl0: <3Com 3c905 Fast Etherlink XL 10/100BaseTX> rev 0x00 int a irq 9 on pci0.9.0 xl0: Ethernet address: 00:60:08:5c:f7:49 xl0: autoneg complete, link status good (half-duplex, 100Mbps) ahc0: <Adaptec 2940 Ultra SCSI adapter> rev 0x00 int a irq 10 on pci0.10.0 ahc0: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs vga0: <S3 ViRGE DX/GX graphics accelerator> rev 0x01 int a irq 11 on pci0.12.0 Probing for devices on PCI bus 1: Probing for PnP devices: CSN 1 Vendor ID: CTL00f0 [0xf0008c0e] Serial 0xffffffff Comp ID: PNPb02f [0x2fb0d041] pcm1 (SB16pnp <Vibra16X> sn 0xffffffff) at 0x220-0x22f irq 5 drq 1 flags 0x13 on isa Probing for devices on the ISA bus: sc0 at 0x60-0x6f irq 1 on motherboard sc0: VGA color <16 virtual consoles, flags=0x0> sio0 at 0x3f8-0x3ff irq 4 on isa sio0: type 16550A sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A lpt0 at 0x378-0x37f irq 7 on isa lpt0: Interrupt-driven port lp0: TCP/IP capable interface pcm0 not probed due to drq conflict with pcm1 at 1 psm0 at 0x60-0x64 irq 12 flags 0x24 on motherboard psm0: model Generic PS/2 mouse, device ID 0 wdc1 at 0x170-0x177 irq 15 on isa wdc1: unit 0 (atapi): <Pioneer CD-ROM ATAPI Model DR-A02S 0107/E1.07U>, removable, accel, dma, iordis wcd0: 4133Kb/sec, 128Kb cache, audio play, 256 volume levels, ejectable tray wcd0: door open, unlocked wdc1: unit 1 (atapi): <LS-120 COSM 02 UHD Floppy/025AC0AA>, removable, iordy wfd0: medium type unknown (no disk) npx0 flags 0x1 on motherboard npx0: INT 16 interface Waiting 2 seconds for SCSI devices to settle da1 at ahc0 bus 0 target 1 lun 0 da1: <IBM DCAS-34330W S61A> Fixed Direct Access SCSI2 device da1: 20.0MB/s transfers (10.0MHz, offset 8, 16bit), Tagged Queueing Enabled da1: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C) da2 at ahc0 bus 0 target 2 lun 0 da2: <IBM DCAS-34330W S61A> Fixed Direct Access SCSI2 device da2: 20.0MB/s transfers (10.0MHz, offset 8, 16bit), Tagged Queueing Enabled da2: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C) da0 at ahc0 bus 0 target 0 lun 0 da0: <IBM DCAS-34330W S61A> Fixed Direct Access SCSI2 device da0: 20.0MB/s transfers (10.0MHz, offset 8, 16bit), Tagged Queueing Enabled da0: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C) da3 at ahc0 bus 0 target 3 lun 0 da3: <IBM DCAS-34330W S61A> Fixed Direct Access SCSI2 device da3: 20.0MB/s transfers (10.0MHz, offset 8, 16bit), Tagged Queueing Enabled da3: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C) changing root device to da0s1a Oct 25 17:56:19 shelob /kernel: xl0: Ethernet address: 00:60:08:5c:f7:49 Oct 25 17:56:19 shelob /kernel: xl0: autoneg complete, link status good (half-duplex, 10Mbps) Oct 25 18:38:36 shelob /kernel: xl0: promiscuous mode enabled Oct 28 18:18:52 shelob /kernel: xl0: transmission error: d0 Nov 6 19:55:26 shelob /kernel: xl0: Ethernet address: 00:60:08:5c:f7:49 Nov 6 19:55:26 shelob /kernel: xl0: autoneg complete, link status good (half-duplex, 10Mbps) Nov 6 21:17:34 shelob /kernel: xl0: < Nov 6 21:17:34 shelob /kernel: xl0: Ethernet address: 00:60:08:5c:f7:49 Nov 6 21:17:34 shelob /kernel: xl0: autoneg complete, link status good (half-duplex, 100Mbps) Nov 6 21:20:57 shelob /kernel: xl0: selecting MII, 100Mbps, half duplex Nov 6 21:20:57 shelob /kernel: xl0: selecting MII, 100Mbps, full duplex Nov 12 11:58:38 shelob /kernel: xl0: transmission error: d0 Nov 12 11:58:38 shelob /kernel: xl0: transmission error: 90 Nov 12 11:58:38 shelob /kernel: xl0: transmission error: 90 Nov 12 11:58:38 shelob /kernel: xl0: transmission error: d0 Nov 12 12:01:40 shelob /kernel: xl0: < Nov 12 12:01:40 shelob /kernel: xl0: Ethernet address: 00:60:08:5c:f7:49 Nov 12 12:01:40 shelob /kernel: xl0: autoneg complete, link status good (half-duplex, 100Mbps) Nov 12 13:04:14 shelob /kernel: xl0: transmission error: 90 Nov 12 13:08:54 shelob /kernel: xl0: < Nov 12 13:08:54 shelob /kernel: xl0: Ethernet address: 00:60:08:5c:f7:49 Nov 12 13:08:54 shelob /kernel: xl0: autoneg complete, link status good (half-duplex, 100Mbps) To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-bugs" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199811121131.OAA24109>