Date: Sun, 21 Jan 2001 00:43:53 -0500 From: The Babbler <bts@babbleon.org> To: MIHIRA Yoshiro <sanpei@sanpei.org>, freebsd-mobile@freebsd.org, Greg Smith <gregsmith59@hotmail.com>, Pat Wendorf <beholder@unios.dhs.org> Subject: Re: Linksys 10/100 + 56K Modem PC Card (ethernet only) Message-ID: <3A6A7719.8E4192C0@babbleon.org> References: <200101200819.f0K8Jvr03803@lavender.sanpei.org> <3A6A6885.AE625005@babbleon.org>
next in thread | previous in thread | raw e-mail | index | archive | help
FWIW, using the PCMPC100 config from Pat Wendorf didn't work for me with the PCMLM56, either. I'm quite out of ideas; I've already tried config slots 0x0 through 0xa . . . The Babbler wrote: > > Ok, thank you for the assistance. > Per Greg Smith's advice, I set boot -v, and this produced messages which > reminded me that I didn't re-compile the kernel (as I had to do to get > another Linksys card on a another FreeBSD laptop) to get rid of the > spurious "ed1" parameters. But it still doesn't work. > > I checked the address/port ranges dumped by boot -v, but they don't seem > to conflict with 0x2f8-2ff or 300-31f. > > Per Mihra Yoshiro's advice, I try the "auto" slot and the "?" IRQ. But > it still doesn't work. > (Same message as with slot 3.) > > Next I shall try the > > config 0x3 ed0 ? 0x8000 > > trick from Pat Wendorf. I don't hold out high hopes, but it's worth a > try. > > Pat Wendorf: > > - How did you determine tthat 8000 was correct, and > - How did you know that you could put the address there? > My purusal of the man page showed that it took IRQs but not ioaddrs. > Was I mis-reading it? > > Thanks for everybody's help . . . > > MIHIRA Yoshiro wrote: > > > > bts@babbleon.org wrote: > > > > >> I'm trying to get the a PCCARD working; specifically the card in the > > >> title above. Although it's a modem/ethernet card, I now have a cable > > >> modem so I only care about the ethernet aspect of the card. It works > > >> fine under Linux, which has this view of it: > > >> > > >> eth0: NE2000 Compatible: io 0x300, irq 3, hw_addr 00:E0:98:70:F9:6A > > >> > > >> > > >> For for FreeBSD, it's not known to the pccard data base. I've tried > > >> creating a simple entry for it, but I'm not having much luck. Here's my > > >> current pccard.conf entry for it: > > >> > > >> # This is the Linksys card I have, with the fat holder. > > >> card "Linksys" "EtherFast 10&100 + 56K PC Card (PCMLM56)" > > >> config 0x3 "ed" 3 > > >> insert /etc/pccard_ether $device start > > >> remove /etc/pccard_ether $device stop > > > > What version of FreeBSD did you use? 4.1-RELEASE or 4.2-RELEASE ? > > > > If you use 4.2-RELEASE or later, please try below configuration. > > > > # This is the Linksys card I have, with the fat holder. > > card "Linksys" "EtherFast 10&100 + 56K PC Card (PCMLM56)" > > config auto "ed" ? > > insert /etc/pccard_ether $device start > > remove /etc/pccard_ether $device stop > > > > Cheers. > > MIHIRA Yoshiro > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > with "unsubscribe freebsd-mobile" in the body of the message > > -- > "Brian, the man from babble-on" bts@babbleon.org > Brian T. Schellenberger http://www.babbleon.org > Support http://www.eff.org. Support decss defendents. > Support http://www.programming-freedom.org. Boycott amazon.com. > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-mobile" in the body of the message -- "Brian, the man from babble-on" bts@babbleon.org Brian T. Schellenberger http://www.babbleon.org Support http://www.eff.org. Support decss defendents. Support http://www.programming-freedom.org. Boycott amazon.com. To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3A6A7719.8E4192C0>