Date: Thu, 11 Mar 2004 12:46:49 +0100 From: "Alberto (WarfoX) De Boni" <warfox@neobe.it> To: freebsd-questions@freebsd.org Subject: Problems with atacontrol and Hightpoint 730 raid Hardware. 5.2 release. Message-ID: <405051A9.1000703@neobe.it>
next in thread | raw e-mail | index | archive | help
Hi all, i'm experiencing some problems with FreeBsd 5.2 and an Highpoint raid controller (but it happens also with a promise Fasttrack TX2). I'm pretty sure it's my failure, but i can't understand what i miss. I'm doing this test on 5.x because i plan to migrate from 4.x to new release as soon as it'll released as a production platform, so i need as much informations as i can. I've done a lot of test: 1- the first test was done creating a RAID 1 array directly from HPT Bios. I've two devices ad4 and ad6 and a raid one ar0 as i expect. ATA channel 2: Master: ad4 <Maxtor 6Y080L0/YAR41BW0> ATA/ATAPI rev 7 Slave: no device present ATA channel 3: Master: ad6 <Maxtor 6Y080L0/YAR41BW0> ATA/ATAPI rev 7 Slave: no device present arc# atacontrol status ar0 ar0: ATA RAID1 subdisks: ad4 ad6 status: READY I've installed *BSD successfully without any flaws, rebooted, and all was working fine. Then i tried a failure problem on ad4, i've simulated it detaching the ata channel: atacontrol detach 2. And i've got a degraded array (that's fine). arc# atacontrol status ar0 ar0: ATA RAID1 subdisks: DOWN ad6 status: DEGRADED Then i detach physically the drive replacing it with a new one (supposed the procedure to substitute a failure HDD).Attached it to channel 2. arc# atacontrol attach 2 Master: ad4 <Maxtor 6Y080L0/YAR41BW0> ATA/ATAPI rev 7 Slave: no device present and then looking at the raid status: arc# atacontrol status ar0 ar0: ATA RAID1 subdisks: DOWN ad6 status: DEGRADED All as it was planned. Now i've tried to rebuild the raid, and here we are with problems: arc# atacontrol rebuild ar0 arc# arc# arc# atacontrol status ar0 ar0: ATA RAID1 subdisks: DOWN ad6 status: DEGRADED The rebuild command quits immediatly rebuilding almost nothing. And the raid was still in degraded mode. Ok. Pherhaps i made a mistake attaching the drive and not attaching a spare drive. To avoid any problem i've reinstalled all from scrath and execute all the operations except the atacontrol attach. Then.. manpages for atacontrol reports: atacontrol addspare raid disk So, it was supposed to add the channel and then add disk to raid: new disk as master arc# atacontrol attach 2 Master: ad4 <Maxtor 6Y080L0/YAR41BW0> ATA/ATAPI rev 7present Slave: no device arc# atacontrol addspare ar0 ad4 atacontrol: ioctl(ATARAIDADDSPARE): Device busy and as slave. arc# atacontrol attach 2 Master: no device present Slave: ad5 <Maxtor 6Y080L0/YAR41BW0> ATA/ATAPI rev 7 arc# atacontrol addspare ar0 ad5 atacontrol: ioctl(ATARAIDADDSPARE): Device busy So... what the hell i've got to do to rebuild the array??? Obviously when i reboot, HPT Bios ask for replacing failure drive, and ask for rebuild... blocking the machine for more than 40 minutes... and this is not acceptable for me. The hardware is a KD7 RAID with Highpoint 730 controller, Duron 1600. Two 80 Gb Maxtor 7200 Rpm 8 Mb. Any Idea? Thanks in advance.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?405051A9.1000703>