Date: Sat, 22 Nov 2008 17:53:54 +0100 (CET) From: Pieter Donche <Pieter.Donche@ua.ac.be> To: Glen Barber <glen.j.barber@gmail.com> Cc: freebsd-questions@freebsd.org Subject: Re: FreeBSD in VMWare box Message-ID: <Pine.GSO.4.63.0811221751250.26493@hmacs.cmi.ua.ac.be> In-Reply-To: <4ad871310811220544g32fadf85t7a6330fa98ce2895@mail.gmail.com> References: <Pine.GSO.4.63.0811112006430.700@hmacs.cmi.ua.ac.be> <20081111192900.GA5398@icarus.home.lan> <Pine.GSO.4.63.0811221353080.20190@hmacs.cmi.ua.ac.be> <4ad871310811220508y2b223ad4k31937f4f231b2fab@mail.gmail.com> <Pine.GSO.4.63.0811221435290.21304@hmacs.cmi.ua.ac.be> <4ad871310811220544g32fadf85t7a6330fa98ce2895@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Sat, 22 Nov 2008, Glen Barber wrote:
> On Sat, Nov 22, 2008 at 8:43 AM, Pieter Donche <Pieter.Donche@ua.ac.be> wrote:
>> On Sat, 22 Nov 2008, Glen Barber wrote:
>>
>>>> The PC with WMware is connect to internet. Should one configure
>>>> Ethernet then. If yes, what static IP parameters must one enter??
>>>
>>> This would be contingent on how you have networking set up. Do you
>>> have NAT or Bridged only? If NAT, use rc.conf with the inet address
>>> of your choice and the netmask for your NAT.
>>
>> My PC is connected to Internet using an ADSL modem to connect to an ISP.
>> It uses IP 10.0.0.somevalue, netmask 255.255.255.0, no gateway specified
>> and two DNS server IP addresses which my ISP asked to use.
>>
>> Is this 'NAT' or 'Bridged'.
>>
>
> You'd have to tell me; it's your VM. Check the network settings in the
> management interface.
(I previously installed an openSUSE 10.3 VM, and needed not enter any
TCP/IP parameter, and could use netwerking afterwards)
The default settings of my VMware are
(from Edit / Virtual Network Editor)
Summary
Virt. Network - Summary - Subnet - DHCP
VMnet0 (Bridged) - Bridged to an automatically choosen adapter - -
VMnet1 (Host-only) - A private nw shared with the host - 192.168.72.0 - Enabled
VMnet8 (NAT) - Used to share the host's IP address - 192.168.173.0 - Enabled
Automatic Bridging
CHECKED: AUtomatically choose an available physical netwerk adapter to
bridge to VMnet0
Host Virtual Netwerk Mapping
VMnet0 Brigded to an automatically chosen adapter
(here I can also select my physical network card)
VMnet1 VMware Network Adapter VMnet1 (only choice)
VMnet2 (and 3 to 7 and 9): Not bridged
(here I can also select my physical network card)
VMnet8 VMware Network Adapter VMnet8 (only choice)
Host Virtual Adapters
Network Adpater Virt.Nw Status
VMware Network Adapter VMnet1 VMnet1 Enabled
VMware Network Adapter VMnet8 VMnet8 Enabled
DHCP
Virtual Network Subnet Netmask Description
VMnet1 192.168.72.0 255.255.255.0 vmnet1
VMnet8 192.168.137.0 255.255.255.0 vmnet8
NAT
VMnet host: VMnet8
Gateway IP address : 192.168.137.2 [ grey ]
Netmask: 255.255.255.0 [ grey ]
Nat Service
Service Status: Started
Service request: [ empty ]
>> Can I enter values and then what values, for host, domain, IPV4 gateway,
>> Name server, IPV4 address, netmask in the screen presented during FreeBSD
>> install
>> or should i use Cancel in that screen and make changes in system files (and
>> what changes in what system files)?
>>
>
> Either will work.
>
> --
> Glen Barber
>
>
> "If you have any trouble sounding condescending, find a Unix user to
> show you how it's done."
> --Scott Adams
>
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.GSO.4.63.0811221751250.26493>