Skip site navigation (1)Skip section navigation (2)
Date:      Sun, 13 Sep 2020 11:53:37 -0700
From:      Adrian Chadd <adrian.chadd@gmail.com>
To:        Anthony Jenkins <Scoobi_doo@yahoo.com>
Cc:        "freebsd-wireless@freebsd.org" <freebsd-wireless@freebsd.org>
Subject:   Re: Atheros QCA6174 (ath10k) not working
Message-ID:  <CAJ-VmonV1oDgXi2d0Ve4=-6So5DRbyFzrfWaZEqw=rGn7nc7ow@mail.gmail.com>
In-Reply-To: <9beac50d-6c08-0c0a-7f42-f1e95ae31d8f@yahoo.com>
References:  <9beac50d-6c08-0c0a-7f42-f1e95ae31d8f.ref@yahoo.com> <9beac50d-6c08-0c0a-7f42-f1e95ae31d8f@yahoo.com>

next in thread | previous in thread | raw e-mail | index | archive | help
hi!

we're still working on this. It's going to take some time.

thanks,



-adrian


On Sun, 13 Sep 2020 at 11:12, Anthony Jenkins via freebsd-wireless <
freebsd-wireless@freebsd.org> wrote:

> I have a Killer 1535 802.11ac wireless card (chipset = Qualcomm Atheros
> QCA6174).  I am using the ath10k/athp driver from git repo
> https://github.com/erikarn/athp.git .  Driver loads, but trying to start
> the interface fails.  What should I be looking at to fix this?
>
> service netif start wlan2:
> ---------------------------------------------------------------------------
> ifconfig: SIOCIFCREATE2: Input/output error
> ifconfig: interface wlan2 does not exist
> ifconfig: interface wlan2 does not exist
> ifconfig: interface wlan2 does not exist
> ifconfig: interface wlan2 does not exist
> Starting wpa_supplicant.
> /etc/rc.d/wpa_supplicant: WARNING: failed to start wpa_supplicant
> ifconfig: interface wlan2 does not exist
> rtsol: failed to get link layer information for wlan2
> rtsol: failed to initialize wlan2
> Starting Network: wlan2.
> ifconfig: interface wlan2 does not exist
> ---------------------------------------------------------------------------
>
> Kernel messages:
> ---------------------------------------------------------------------------
> athp0: ath10k_start: called; state=0
> athp0: ath10k_start: state=1
> athp0: ath10k_download_cal_dt: TODO: device tree check
> athp0: ath10k_wmi_event_service_ready_work: TODO: EEPROM code: 0x00000069
> athp0: htc ep 2 out of TX credits (0 < 1)
> athp0: htc ep 2 out of TX credits (0 < 1)
> ...
> athp0: htc ep 2 out of TX credits (0 < 1)
> athp0: htc ep 2 out of TX credits (0 < 1)
> athp0: ath10k_wmi_cmd_send: failed (-35)
> athp0: failed to enable PMF QOS: -35
> athp0: ath10k_core_stop: state=1
> athp0: ath10k_wait_for_suspend: state=1
> athp0: ath10k_wmi_pdev_suspend_target: called
> athp0: htc ep 2 out of TX credits (0 < 1)
> athp0: htc ep 2 out of TX credits (0 < 1)
> ...
> athp0: htc ep 2 out of TX credits (0 < 1)
> athp0: htc ep 2 out of TX credits (0 < 1)
> athp0: ath10k_wmi_cmd_send: failed (-35)
> athp0: could not suspend target (-35)
> athp0: ath10k_pci_irq_sync: TODO
> athp0: ath10k_pci_kill_tasklet: called
> athp0: ath10k_htt_tx_free: called
> athp0: ath10k_htt_tx_free: tearing down htt locks
> athp0: athp_vap_create: ath10k_start failed; ret=-35
> ---------------------------------------------------------------------------
>
> Some notable errors from 'kldload if_athp.ko':
>
> * Driver fails to load firmware file athp_QCA6174_hw3.0/firmware-5.bin;
> it does load file 'athp_QCA6174_hw3.0_firmware-4.bin'.
>
> athp0: ath10k_fetch_fw_file: firmware_get: athp_cal-pci-athp0.bin
> athp_cal-pci-athp0.bin: could not load firmware image, error 2
> athp0: ath10k_fetch_fw_file: firmware_get: athp_QCA6174_hw3.0_board.bin
> firmware: 'athp_QCA6174_hw3.0_board.bin' version 1: 8124 bytes loaded at
> 0xffffffff84458000
> athp0: ath10k_fetch_fw_file: firmware_get:
> athp_QCA6174_hw3.0_firmware-5.bin
> athp_QCA6174_hw3.0_firmware-5.bin: could not load firmware image, error 2
> athp0: could not fetch firmware file 'athp_QCA6174_hw3.0/firmware-5.bin':
> -1
> athp0: ath10k_fetch_fw_file: firmware_get:
> athp_QCA6174_hw3.0_firmware-4.bin
> firmware: 'athp_QCA6174_hw3.0_firmware-4.bin' version 1: 733784 bytes
> loaded at 0xffffffff8445d000
>
> I assume file 'athp_cal-pci-athp0.bin' is optional calibration data.
>
> * 'htc ep 2 out of TX credits (0 < 1)' repeated 144 times
>
> * ath10k_wmi_cmd_send failure
>
> athp0: ath10k_wmi_cmd_send: failed (-35)
> athp0: could not suspend target (-35)
>
>
> My full kernel messages from kldload(8) and netif are at
> http://www.qtchat.org/~ajenkins/ .
>
> Thanks,
> Anthony Jenkins
>
>
> _______________________________________________
> freebsd-wireless@freebsd.org mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-wireless
> To unsubscribe, send any mail to "freebsd-wireless-unsubscribe@freebsd.org
> "
>



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CAJ-VmonV1oDgXi2d0Ve4=-6So5DRbyFzrfWaZEqw=rGn7nc7ow>