From owner-freebsd-questions Sun Dec 12 14:53:40 1999 Delivered-To: freebsd-questions@freebsd.org Received: from sax.sax.de (sax.sax.de [193.175.26.33]) by hub.freebsd.org (Postfix) with ESMTP id 7E3E114D39 for ; Sun, 12 Dec 1999 14:53:37 -0800 (PST) (envelope-from mw@theatre.sax.de) Received: (from uucp@localhost) by sax.sax.de (8.9.3/8.9.3) with UUCP id XAA22746; Sun, 12 Dec 1999 23:51:31 +0100 (CET) Received: by theatre.sax.de (8.9.3/8.6.12-s1) id XAA60004; Sun, 12 Dec 1999 23:43:52 +0100 (CET) Date: Sun, 12 Dec 1999 23:43:52 +0100 From: Martin Welk To: John Cc: David Bein , freebsd-questions@FreeBSD.ORG Subject: Re: Adaptec/SCSI question ... Message-ID: <19991212234352.B59717@theatre.sax.de> Reply-To: mw@sax.de References: <945003920/bein@sanity.mass.pyramid.com> <4.1.19991212111457.00954a60@mail.udel.edu> Mime-Version: 1.0 Content-Type: text/plain; charset=us-ascii X-Mailer: Mutt 1.0i In-Reply-To: <4.1.19991212111457.00954a60@mail.udel.edu>; from papalia@UDel.Edu on Sun, Dec 12, 1999 at 11:27:58AM -0500 Organization: Private UUCP/Usenet site. X-Phone: +49 3731 458867 X-Operating-System: FreeBSD http://www.freebsd.org/ Sender: owner-freebsd-questions@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG On Sun, Dec 12, 1999 at 11:27:58AM -0500, John wrote: > I am *NOT* sure how to 2940U2W works for which ports you can use in which > configurations, but I'm going to go out on a limb and say that, once again, > you can't put the devices in a "Y" pattern. AFAIR the 2940 doesn't have that internal SCSI bridge (AIC3660 chip) that for example the Asus P2B-S motherboard has (you can build and use Y-a-like configurations, for example, when using a mixture of 8-bit-wide and 16-bit- wide connected SCSI devices (CD-ROM, hard disk, Tandberg SLR6) and LVD devices, and it run's fine. A collegue at work bought a 2930U2W about one or two weeks ago, this one as Fast-SCSI internal and external connectors and an internal U2W connector, nothing for UW. This configuration wasn't that much expensive and makes sense, as newer disks are mainly U2W and you have often one or the other Fast-SCSI device (CD-ROM, external Scanner, CD-R). And this adapter has that AIC3660 SCSI bridge which should make it possible to use Y configurations (devices on all three connectors), but we haven't used that yet. That adapter is based on an 7890 chipset, AFAIR. > room, or c) the device I want doesn't fit well internally. I think that > call is up to you. Oh... and internal cables are a HECK of a lot cheaper > than external ones ;) Another reason at work was the possibility to share devices (at times where good CD-R's were expensive) or the impossibility to squeeze a scanner into one of those usual PC cases :-) Regards, Martin -- /| /| | /| / ,,You know, there's a lot of opportunities, / |/ | artin |/ |/ elk if you're knowing to take them, you know, there's a lot of opportunities, Freiberg/Saxony, Germany if there aren't you can make them, mw@sax.de / mw@theatre.sax.de make or break them!'' (Tennant/Lowe) To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message