Date: Sun, 27 Apr 2008 14:08:11 -0500 (CDT) From: Greg Rivers <gcr+freebsd-ports@tharned.org> To: freebsd-ports@freebsd.org Subject: smartmontools-5.38 and cciss RAID controller Message-ID: <alpine.BSF.1.10.0804271010060.1116@nc8000.tharned.org>
next in thread | raw e-mail | index | archive | help
The recent incorporation of the FreeBSD CISS SMART support into the
mainstream smartmontools distribution has had some unexpected results on
several HP ProLiant DL380 G3 machines. I have five DL380/G3s with four
drives each; all have the same symptoms now: querying a given ciss/scsi
target gives results for the wrong drive:
smartctl -iH -d cciss,0 /dev/ciss0 gives results for target 2
" cciss,1 " " 3
" cciss,2 " does not see the drive there
" cciss,3 " gives results for target 0
" cciss,4 " " 1
The actual drives are at targets 0, 1, 2 and 3.
I'm wondering if this is due to the CISS controller type being
misidentified. Before, querying a target with no drive present yielded
"Device: COMPAQ Smart Array 5i Version: 2.66", which is correct.
Now, querying a target with no drive yields a variable result,
eg. "Device: COMPAQ PROLIANT 4LCI DT Version: 1.84"
or "Device: COMPAQ PROLIANT 6L2I Version: 0.01"
which are all incorrect. See below for more detailed information.
Has anyone else seen a similar problem? Should I file a FreeBSD PR, or
take this up with the smartmontools project?
--
Greg Rivers
The CISS controller as seen by `pciconf -lv`:
------------------------------------------------------------------------------
ciss0@pci0:1:3:0: class=0x010400 card=0x40800e11 chip=0xb1780e11 rev=0x01 hdr=0x00
vendor = 'Compaq Computer Corp (Now owned by Hewlett-Packard)'
device = 'CISSB SMART2 Array Controller'
class = mass storage
subclass = RAID
Relevant `dmesg` output:
------------------------------------------------------------------------------
ciss0: <Compaq Smart Array 5i> port 0x3000-0x30ff mem 0xf7cc0000-0xf7cfffff,0xf7bf0000-0xf7bf3fff irq 30 at device 3.0 on pci1
ciss0: [ITHREAD]
da0 at ciss0 bus 0 target 0 lun 0
da0: <COMPAQ RAID 1 VOLUME OK> Fixed Direct Access SCSI-0 device
da0: 135.168MB/s transfers
da0: 69459MB (142253280 512 byte sectors: 255H 32S/T 17433C)
da1 at ciss0 bus 0 target 1 lun 0
da1: <COMPAQ RAID 1 VOLUME OK> Fixed Direct Access SCSI-0 device
da1: 135.168MB/s transfers
da1: 69459MB (142253280 512 byte sectors: 255H 32S/T 17433C)
The correct SMART status before the update to version 5.38:
------------------------------------------------------------------------------
# smartctl -iH -d cciss,0 /dev/ciss0
smartctl version 5.37 [i386-portbld-freebsd7.0] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: COMPAQ BD0728856A Version: HPB0
Serial number: AAL1P4800F7E0435
Device type: disk
Transport protocol: Parallel SCSI (SPI-4)
Local Time is: Mon Apr 21 13:41:01 2008 CDT
Device supports SMART and is Enabled
Temperature Warning Enabled
SMART Health Status: OK
# smartctl -iH -d cciss,1 /dev/ciss0
smartctl version 5.37 [i386-portbld-freebsd7.0] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: COMPAQ BD07289BB8 Version: HPB1
Serial number: DEL1P7100YH50703
Device type: disk
Transport protocol: Parallel SCSI (SPI-4)
Local Time is: Mon Apr 21 13:41:07 2008 CDT
Device supports SMART and is Enabled
Temperature Warning Enabled
SMART Health Status: OK
# smartctl -iH -d cciss,2 /dev/ciss0
smartctl version 5.37 [i386-portbld-freebsd7.0] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: COMPAQ BD07286224 Version: HPB6
Serial number: UUA1P4A0427W0444
Device type: disk
Transport protocol: Parallel SCSI (SPI-4)
Local Time is: Mon Apr 21 13:41:11 2008 CDT
Device supports SMART and is Enabled
Temperature Warning Enabled
SMART Health Status: OK
# smartctl -iH -d cciss,3 /dev/ciss0
smartctl version 5.37 [i386-portbld-freebsd7.0] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: COMPAQ BD0728856A Version: HPB0
Serial number: AAL1P4800FML0435
Device type: disk
Transport protocol: Parallel SCSI (SPI-4)
Local Time is: Mon Apr 21 13:41:16 2008 CDT
Device supports SMART and is Enabled
Temperature Warning Enabled
SMART Health Status: OK
# smartctl -iH -d cciss,4 /dev/ciss0
smartctl version 5.37 [i386-portbld-freebsd7.0] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: COMPAQ Smart Array 5i Version: 2.66
>> Terminate command early due to bad response to IEC mode page
A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.
# smartctl -iH -d cciss,5 /dev/ciss0
smartctl version 5.37 [i386-portbld-freebsd7.0] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: COMPAQ Smart Array 5i Version: 2.66
>> Terminate command early due to bad response to IEC mode page
A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.
#
The erroneous SMART status after the update to version 5.38:
------------------------------------------------------------------------------
# smartctl -iH -d cciss,0 /dev/ciss0
smartctl version 5.38 [i386-portbld-freebsd7.0] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: COMPAQ BD07286224 Version: HPB6
Serial number: UUA1P4A0427W0444
Device type: disk
Transport protocol: Parallel SCSI (SPI-4)
Local Time is: Mon Apr 21 13:48:52 2008 CDT
Device supports SMART and is Enabled
Temperature Warning Enabled
SMART Health Status: OK
# smartctl -iH -d cciss,1 /dev/ciss0
smartctl version 5.38 [i386-portbld-freebsd7.0] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: COMPAQ BD0728856A Version: HPB0
Serial number: AAL1P4800FML0435
Device type: disk
Transport protocol: Parallel SCSI (SPI-4)
Local Time is: Mon Apr 21 13:48:56 2008 CDT
Device supports SMART and is Enabled
Temperature Warning Enabled
SMART Health Status: OK
# smartctl -iH -d cciss,2 /dev/ciss0
smartctl version 5.38 [i386-portbld-freebsd7.0] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: COMPAQ PROLIANT 4LCI DT Version: 1.84
>> Terminate command early due to bad response to IEC mode page
A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.
# smartctl -iH -d cciss,3 /dev/ciss0
smartctl version 5.38 [i386-portbld-freebsd7.0] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: COMPAQ BD0728856A Version: HPB0
Serial number: AAL1P4800F7E0435
Device type: disk
Transport protocol: Parallel SCSI (SPI-4)
Local Time is: Mon Apr 21 13:49:03 2008 CDT
Device supports SMART and is Enabled
Temperature Warning Enabled
SMART Health Status: OK
# smartctl -iH -d cciss,4 /dev/ciss0
smartctl version 5.38 [i386-portbld-freebsd7.0] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: COMPAQ BD07289BB8 Version: HPB1
Serial number: DEL1P7100YH50703
Device type: disk
Transport protocol: Parallel SCSI (SPI-4)
Local Time is: Mon Apr 21 13:49:05 2008 CDT
Device supports SMART and is Enabled
Temperature Warning Enabled
SMART Health Status: OK
# smartctl -iH -d cciss,5 /dev/ciss0
smartctl version 5.38 [i386-portbld-freebsd7.0] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: COMPAQ PROLIANT 6L2I Version: 0.01
>> Terminate command early due to bad response to IEC mode page
A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.
#
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?alpine.BSF.1.10.0804271010060.1116>