Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 22 Aug 1997 09:46:18 +0000 (GMT)
From:      David Ramahefason <rama@easynet.fr>
To:        Steve Passe <smp@csn.net>
Cc:        smp@FreeBSD.ORG
Subject:   Re: Need Help on installing SMP on SNAP 3.0 
Message-ID:  <Pine.BSF.3.96.970822094446.2624A-100000@casimir.easynet.fr>
In-Reply-To: <199708212056.OAA25112@Ilsa.StevesCafe.com>

next in thread | previous in thread | raw e-mail | index | archive | help
On Thu, 21 Aug 1997, Steve Passe wrote:

> Hi,
> 
> > We've just bought a bi-pentium card:
> > ...
> > The UP boot works fine... the compilation for an SMP kernel
> > works fine... but when I try to boot it, it hangs just before
> > the disk stuff... and nothing occurs...
> > Did someone already tested these cards ??? Could someone tell me the good
> > options to set up in the Kernel config.... 
> 
> this hardware (to the degree you described it) should work fine,  but you
> need to supply MUCH more info to get an answer:
> 
> what version of 3.0?, date, etc.
> what disk controller/disks?
> what SMP options did you use?
> be more specific about what happens, eg, give us the last half dozen messages
>  to come out before it hangs.
> give us the output of "mptable -dmesg" (from a UP kernel is fine).


Ooops tou're right...
here's an output of mptable -verbose -dmesg:


===============================================================================

MPTable, version 2.0.13

 looking for EBDA pointer @ 0x040e, NOT found
 searching CMOS 'top of mem' @ 0x0009fc00 (639K)
 searching BIOS @ 0x000f0000

 MP FPS found in BIOS @ physical addr: 0x000f61f0

-------------------------------------------------------------------------------

MP Floating Pointer Structure:

  location:			BIOS
  physical address:		0x000f61f0
  signature:			'_MP_'
  length:			16 bytes
  version:			1.1
  checksum:			0x4b
  mode:				Virtual Wire

-------------------------------------------------------------------------------

MP Config Table Header:

  physical address:		0x000f5dec
  signature:			'PCMP'
  base table length:		244
  version:			1.1
  checksum:			0x5c
  OEM ID:			'OEM00000'
  Product ID:			'PROD00000000'
  OEM table pointer:		0x00000000
  OEM table size:		0
  entry count:			22
  local APIC address:		0xfee00000
  extended table length:	0
  extended table checksum:	0

-------------------------------------------------------------------------------

MP Config Base Table Entries:

--
Processors:	APIC ID	Version	State		Family	Model	Step	Flags
		 0	 0x10	 BSP, usable	 5	 2	 12	 0x03bf
		 1	 0x10	 AP, usable	 5	 2	 12	 0x03bf
--
Bus:		Bus ID	Type
		 0	 PCI   
		 1	 ISA   
--
I/O APICs:	APIC ID	Version	State		Address
		 2	 0x11	 usable		 0xfec00000
--
I/O Ints:	Type	Polarity    Trigger	Bus ID	 IRQ	APIC ID	INT#
		ExtINT	 conforms    conforms	     1	   0	      2	   0
		INT	 conforms    conforms	     1	   1	      2	   1
		INT	 conforms    conforms	     1	   0	      2	   2
		INT	 conforms    conforms	     1	   3	      2	   3
		INT	 conforms    conforms	     1	   4	      2	   4
		INT	 conforms    conforms	     1	   5	      2	   5
		INT	 conforms    conforms	     1	   6	      2	   6
		INT	 conforms    conforms	     1	   7	      2	   7
		INT	 conforms    conforms	     1	   8	      2	   8
		INT	 conforms    conforms	     1	   9	      2	   9
		INT	 conforms    conforms	     1	  14	      2	  14
		INT	 conforms    conforms	     1	  15	      2	  15
		INT	active-lo       level	     1	  11	      2	  17
		INT	active-lo       level	     1	  10	      2	  18
		INT	active-lo       level	     1	  12	      2	  19
--
Local Ints:	Type	Polarity    Trigger	Bus ID	 IRQ	APIC ID	INT#
		ExtINT	active-hi        edge	     1	   0	    255	   0
		NMI	active-hi        edge	     1	   0	    255	   1

-------------------------------------------------------------------------------

# SMP kernel config file options:


# Required:
options		SMP			# Symmetric MultiProcessor Kernel
options		APIC_IO			# Symmetric (APIC) I/O

# Useful:
#options		SMP_AUTOSTART		# start the additional CPUs during boot

# Optional (built-in defaults will work in most cases):
#options		NCPU=2			# number of CPUs
#options		NBUS=2			# number of busses
#options		NAPIC=1			# number of IO APICs
#options		NINTR=24		# number of INTs

-------------------------------------------------------------------------------

dmesg output:

Copyright (c) 1992-1997 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
	The Regents of the University of California. All rights reserved.
FreeBSD 3.0-970807-SNAP #0: Thu Aug 21 11:53:10 CEST 1997
    root@analyzer.easynet.fr:/usr/src/sys/compile/ANALYZER
CPU: Pentium (199.43-MHz 586-class CPU)
  Origin = "GenuineIntel"  Id = 0x52c  Stepping=12
  Features=0x3bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,APIC>
real memory  = 134217728 (131072K bytes)
avail memory = 128561152 (125548K bytes)
Probing for devices on PCI bus 0:
chip0: <Intel 82439> rev 0x03 on pci0.0.0
chip1: <Intel 82371SB PCI to ISA bridge> rev 0x01 on pci0.1.0
ahc0: <Adaptec 2940 Ultra SCSI host adapter> rev 0x00 int a irq 10 on pci0.10.0
ahc0: aic7880 Wide Channel, SCSI Id=7, 16 SCBs
ahc0: waiting for scsi devices to settle
scbus0 at ahc0 bus 0
sd0 at scbus0 target 0 lun 0
sd0: <FUJITSU M2952Q-512 0147> type 0 fixed SCSI 2
sd0: Direct-Access 2291MB (4693462 512 byte sectors)
sd1 at scbus0 target 1 lun 0
sd1: <SEAGATE ST34371W 0338> type 0 fixed SCSI 2
sd1: Direct-Access 4148MB (8496960 512 byte sectors)
ahc0:A:6: refuses WIDE negotiation.  Using 8bit transfers
st0 at scbus0 target 6 lun 0
st0: <ARCHIVE Python 28388-XXX 5.AC> type 1 removable SCSI 2
st0: Sequential-Access density code 0x13,  drive empty
vga0: <VGA-compatible display device> rev 0xd3 int a irq 11 on pci0.11.0
de0: <Digital 21140 Fast Ethernet> rev 0x12 int a irq 12 on pci0.13.0
de0: SMC 9332DST 21140 [10-100Mb/s] pass 1.2
de0: address 00:00:c0:17:2f:e6
de0: enabling 100baseTX port
Probing for devices on the ISA bus:
sc0 at 0x60-0x6f irq 1 on motherboard
sc0: VGA color <16 virtual consoles, flags=0x0>
vt0 not probed due to I/O address conflict with sc0 at 0x60
sio0 at 0x3f8-0x3ff irq 4 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
lpt0 at 0x378-0x37f irq 7 on isa
lpt0: Interrupt-driven port
lp0: TCP/IP capable interface
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: NEC 72065B
fd0: 1.44MB 3.5in
wt0 not found at 0x300
scd0 not found at 0x230
npx0 on motherboard
npx0: INT 16 interface
IP packet filtering initialized, divert enabled, logging limited to 100 packets/entry

###
# in fact in SMP mode the boot hangs just here :(

de0: promiscuous mode enabled
de0: receive: 00:60:97:19:c6:8a: bad crc

===============================================================================

Any idea ??

Thanks



/David Ramahefason	Administrateur Systeme/Reseau/
/rama@easynet.fr	Easynet France SA            /
/mobile: 0611647281     0144545333                   /





Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.3.96.970822094446.2624A-100000>