Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 12 Jul 1999 17:10:33 -0700
From:      Mike Smith <mike@smith.net.au>
To:        Wilko Bulte <wilko@yedi.iaf.nl>
Cc:        FreeBSD-hackers@freebsd.org (FreeBSD hackers list)
Subject:   Re: 3.2-STABLE not stable but panicy? 
Message-ID:  <199907130010.RAA02621@dingo.cdrom.com>
In-Reply-To: Your message of "Sat, 10 Jul 1999 21:12:49 %2B0200." <199907101912.VAA00520@yedi.iaf.nl> 

next in thread | previous in thread | raw e-mail | index | archive | help

This is typically symptomatic of poor CPU cooling; all of a sudden you 
are running the CPU at full power 100% of the time, rather than sitting 
in an HLT instruction.  It can be further exacerbated if you're 
overclocking.

> Is it just me/my machine or has 3.2-STABLE become rather unstable and
> panic stricken (sp)?
> 
> Whether it has any correlation I don't know, but it seems to have started
> when I got in the the RC5DES project a couple of days ago.
> 
> Yesterday I got a panic like:
> 
> (no debugging symbols found)...
> IdlePTD 3174400
> initial pcb at 28e864
> panicstr: lockmgr: unknown locktype request 0
> panic messages:
> ---
> panic: lockmgr: unknown locktype request 0
> 
> syncing disks... 160 159 139 113 80 32 done
> 
> dumping to dev 30401, offset 327680
> dump 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73
> 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48
> 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23
> 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 
> ---
> #0  0xc01594ff in boot ()
> (kgdb) bt
> #0  0xc01594ff in boot ()
> #1  0xc0159784 in at_shutdown ()
> #2  0xc01555c4 in lockmgr ()
> #3  0xc017ba88 in vop_stdlock ()
> #4  0xc01f7e19 in ufs_vnoperate ()
> #5  0xc0184863 in vn_lock ()
> #6  0xc017e40b in vget ()
> #7  0xc017a55b in vfs_cache_lookup ()
> #8  0xc01f7e19 in ufs_vnoperate ()
> #9  0xc017cb45 in lookup ()
> #10 0xc017c618 in namei ()
> #11 0xc0180969 in change_dir ()
> #12 0xc01808c7 in chdir ()
> #13 0xc021cf63 in syscall ()
> #14 0xc0213cec in Xint0x80_syscall ()
> #15 0x804919f in ?? ()
> #16 0x804af96 in ?? ()
> #17 0x804904d in ?? ()
> (kgdb) 
> 
> 
> I decided to cvsup the latest -STABLE sources and with a kernel based on
> yesterdays -STABLE I just got (again during a RC5DES run, approx
> 15 minutes after starting it):
> 
> (no debugging symbols found)...
> IdlePTD 3239936
> initial pcb at 29e914
> panicstr: page fault
> panic messages:
> ---
> Fatal trap 12: page fault while in kernel mode
> fault virtual address   = 0x3ff02585
> fault code              = supervisor write, page not present
> instruction pointer     = 0x8:0xc02078b4
> stack pointer           = 0x10:0xc6a158b4
> frame pointer           = 0x10:0xc6a158c0
> code segment            = base 0x0, limit 0xfffff, type 0x1b
>                         = DPL 0, pres 1, def32 1, gran 1
> processor eflags        = interrupt enabled, resume, IOPL = 0
> current process         = 973 (cron)
> interrupt mask          = net tty bio cam 
> trap number             = 12
> panic: page fault
> 
> syncing disks... done
> 
> dumping to dev 30401, offset 327680
> dump 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73
> 72 
> 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47
> 46 45
>  44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20
> 19 1
> 8 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 
> ---
> #0  0xc0159e07 in boot ()
> (kgdb) bt
> #0  0xc0159e07 in boot ()
> #1  0xc015a08c in at_shutdown ()
> #2  0xc021e089 in trap_fatal ()
> #3  0xc021dd67 in trap_pfault ()
> #4  0xc021da0a in trap ()
> #5  0xc02078b4 in zalloci ()
> #6  0xc021ac12 in get_pv_entry ()
> #7  0xc021ada7 in pmap_insert_entry ()
> #8  0xc021b589 in pmap_enter_quick ()
> #9  0xc021b7aa in pmap_object_init_pt ()
> #10 0xc0149c77 in elf_load_section ()
> #11 0xc014a2ae in exec_elf_imgact ()
> #12 0xc01534ff in execve ()
> #13 0xc021e2cb in syscall ()
> #14 0xc0214ecc in Xint0x80_syscall ()
> Cannot access memory at address 0xbfbfd7d8.
> (kgdb) 
> 
> Before someone asks: yes, I checked the CPU fan..
> 
> dmesg:
> 
> 
> Copyright (c) 1992-1999 FreeBSD Inc.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> 	The Regents of the University of California. All rights reserved.
> FreeBSD 3.2-STABLE #0: Sat Jul 10 10:49:28 CEST 1999
>     wilko@yedi.iaf.nl:/usr/freebsd-3.1-stable-src/src/sys/compile/YEDI
> Timecounter "i8254"  frequency 1193182 Hz
> Timecounter "TSC"  frequency 261958495 Hz
> CPU: AMD-K6tm w/ multimedia extensions (261.96-MHz 586-class CPU)
>   Origin = "AuthenticAMD"  Id = 0x562  Stepping = 2
>   Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX>
>   AMD Features=0x400<<b10>>
> real memory  = 100663296 (98304K bytes)
> avail memory = 94621696 (92404K bytes)
> Preloaded elf kernel "kernel" at 0xc0305000.
> Probing for devices on PCI bus 0:
> chip0: <Intel 82439HX PCI cache memory controller> rev 0x03 on pci0.0.0
> chip1: <Intel 82371SB PCI to ISA bridge> rev 0x01 on pci0.7.0
> xl0: <3Com 3c905-TX Fast Etherlink XL> rev 0x00 int a irq 14 on pci0.9.0
> xl0: Ethernet address: 00:60:08:09:b8:f1
> xl0: autoneg not complete, no carrier (forcing half-duplex, 10Mbps)
> vga0: <Matrox MGA 2164W graphics accelerator> rev 0x00 int a irq 14 on pci0.10.0
> Qlogic ISP Driver, FreeBSD CAM Version 0.992, Core Version 1.9
> isp0: <Qlogic ISP 1020/1040 PCI SCSI Adapter> rev 0x05 int a irq 9 on pci0.11.0
> isp0: set PCI line size to 16
> isp0: set PCI latency to 64
> isp0: Ultra Mode Capable
> isp0: Board Revision 1040B, loaded F/W Revision 7.63.0
> isp0: Last F/W revision was 4.53.0
> ncr0: <ncr 53c810 fast10 scsi> rev 0x02 int a irq 11 on pci0.12.0
> Probing for devices on the ISA bus:
> sc0 on isa
> sc0: VGA color <16 virtual consoles, flags=0x0>
> atkbdc0 at 0x60-0x6f on motherboard
> atkbd0 irq 1 on isa
> psm0 irq 12 on isa
> psm0: model Generic PS/2 mouse, device ID 0
> sio0 at 0x3f8-0x3ff irq 4 on isa
> sio0: type 16550A
> sio1 at 0x2f8-0x2ff irq 3 on isa
> sio1: type 16550A
> sio2 at 0x1a0-0x1a7 flags 0x501 on isa
> sio2: type 16550A (multiport)
> sio3 at 0x1a8-0x1af flags 0x501 on isa
> sio3: type 16550A (multiport)
> sio4 at 0x1b0-0x1b7 flags 0x501 on isa
> sio4: type 16550A (multiport)
> sio5 at 0x1b8-0x1bf irq 5 flags 0x501 on isa
> sio5: type 16550A (multiport master)
> fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
> fdc0: FIFO enabled, 8 bytes threshold
> fd0: 1.44MB 3.5in
> ppc0 at 0x378 irq 7 flags 0x40 on isa
> ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
> lpt0: <generic printer> on ppbus 0
> lpt0: Interrupt-driven port
> isic0 at 0xd80 irq 15 flags 0x3 on isa
> isic0: Teles S0/16.3
> isic0: ISAC 2085 Version A1/A2 or 2086/2186 Version 1.1 (IOM-2) (Addr=0x960)
> isic0: HSCX 82525 or 21525 Version 2.1 (AddrA=0x160, AddrB=0x560)
> vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
> npx0 on motherboard
> npx0: INT 16 interface
> IP packet filtering initialized, divert enabled, rule-based forwarding disabled, unlimited logging
> i4b: ISDN call control device attached
> i4bisppp: 2 ISDN SyncPPP device(s) attached
> i4bctl: ISDN system control port attached
> i4btrc: 2 ISDN trace device(s) attached
> Waiting 3 seconds for SCSI devices to settle
> isp0: driver initiated bus reset of bus 0
> changing root device to da0s2a
> da0 at isp0 bus 0 target 0 lun 0
> da0: <DEC RZ1EF-CB (C) DEC 0371> Fixed Direct Access SCSI-2 device 
> da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
> da0: 17365MB (35565080 512 byte sectors: 255H 63S/T 2213C)
> WARNING: / was not properly dismounted
> da1 at isp0 bus 0 target 1 lun 0
> da1: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device 
> da1: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
> da1: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
> cd0 at isp0 bus 0 target 4 lun 0
> cd0: <TOSHIBA CD-ROM XM-5701TA 0557> Removable CD-ROM SCSI-2 device 
> cd0: 10.000MB/s transfers (10.000MHz, offset 8)
> cd0: cd present [1289068 x 512 byte records]
> cd1 at isp0 bus 0 target 3 lun 0
> cd1: <PHILIPS CDD3600 CD-R/RW 2.00> Removable CD-ROM SCSI-2 device 
> cd1: 10.000MB/s transfers (10.000MHz, offset 8)
> cd1: Attempt to query device size failed: NOT READY, Medium not present
> ffs_mountfs: superblock updated for soft updates
> ffs_mountfs: superblock updated for soft updates
> ffs_mountfs: superblock updated for soft updates
> ffs_mountfs: superblock updated for soft updates
> 
> Comments invited, I'll build and boot a kernel with debugging symbols in the
> meantime.
> 
> Wilko
> --
> |   / o / /  _  	 Arnhem, The Netherlands	- Powered by FreeBSD -
> |/|/ / / /( (_) Bulte 	 WWW  : http://www.tcja.nl 	http://www.freebsd.org
> 
> 
> To Unsubscribe: send mail to majordomo@FreeBSD.org
> with "unsubscribe freebsd-hackers" in the body of the message
> 

-- 
\\  The mind's the standard       \\  Mike Smith
\\  of the man.                   \\  msmith@freebsd.org
\\    -- Joseph Merrick           \\  msmith@cdrom.com




To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hackers" in the body of the message




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199907130010.RAA02621>