Date: Wed, 7 Oct 2020 05:51:32 +0200 From: Klaus Cucinauomo <maciphone2@googlemail.com> To: freebsd-arm@freebsd.org Subject: Re: RPI4 U-Boot 2020.10-rc5 please test xhci feature Message-ID: <C50A9048-FA16-4238-9639-AD2F5AEF64F8@googlemail.com> In-Reply-To: <81140AD2-2AAF-4378-ABB2-8F5B608DE7F7@googlemail.com> References: <81140AD2-2AAF-4378-ABB2-8F5B608DE7F7@googlemail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
> Am 05.10.2020 um 07:45 schrieb Klaus Cucinauomo = <maciphone2@googlemail.com>: >=20 > ( https://wiki.freebsd.org/arm/Raspberry%20Pi#RPI4 ) >=20 > new compiled U-Boot version U-Boot 2020.10-rc5 >=20 > =E2=80=94- 1st try with default settings/files/configuratios ext. = USB-SSD/ no SD-card present:=E2=80=94 >=20 > =E2=80=A6=E2=80=A6=E2=80=A6..U-Boot 2020.10-rc5 (Oct 05 2020 - = 03:08:23 +0000) >=20 > DRAM: 7.9 GiB > RPI 4 Model B (0xd03114) > MMC: mmc@7e300000: 1, emmc2@7e340000: 0 > Loading Environment from FAT... In: serial > Out: vidconsole > Err: vidconsole > Net: eth0: ethernet@7d580000 > PCIe BRCM: link up, 5.0 Gbps x1 (SSC) > starting USB... > Bus xhci_pci: probe failed, error -110 > No working controllers found=E2=80=A6=E2=80=A6=E2=80=A6. > =E2=80=94 > 2020.10-rc5 boots fine from SD-card >=20 > happy testing=20 >=20 > thanks > Regards > Klaus >=20 >=20 The 4GB-model scans xhci correctly (although not detecting kernel/filesystem for now in early testing) (Same disk as on 8GB-test,no SD-card present, `ve changed some files in = msdos-partition (start4.elf, config.txt,/overlays etc.)) while the=20 8GB model needs further patches because the VL805 - firmware=20 is no more loaded by an own eeprom , so has to be loaded explicitly by = the=20 SoC's VideoCore. U-Boot 2020.10-rc5 (Oct 05 2020 - 03:08:23 +0000) DRAM: 3.1 GiB RPI 4 Model B (0xc03111) MMC: mmc@7e300000: 1, emmc2@7e340000: 0 Loading Environment from FAT... In: serial Out: serial Err: serial Net: eth0: ethernet@7d580000 PCIe BRCM: link up, 5.0 Gbps x1 (SSC) starting USB... Bus xhci_pci: Register 5000420 NbrPorts 5 Starting the controller USB XHCI 1.00 scanning bus xhci_pci for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Hit any key to stop autoboot: 0=20 Card did not respond to voltage select! Device 0: Vendor: JMicron Rev: 3202 Prod: Tech =20 Type: Hard Disk Capacity: 114473.4 MB =3D 111.7 GB (234441648 x 512) ... is now current device Scanning usb 0:1... Found EFI removable media binary efi/boot/bootaa64.efi libfdt fdt_check_header(): FDT_ERR_BADMAGIC Scanning disk mmc@7e300000.blk... Disk mmc@7e300000.blk not ready Card did not respond to voltage select! Scanning disk emmc2@7e340000.blk... Disk emmc2@7e340000.blk not ready Scanning disk usb_mass_storage.lun0... ** Unrecognized filesystem type ** Found 3 disks No EFI system partition BootOrder not defined EFI boot manager: Cannot load any image 688192 bytes read in 5 ms (131.3 MiB/s) libfdt fdt_check_header(): FDT_ERR_BADMAGIC Booting /efi\boot\bootaa64.efi Consoles: EFI console =20 Reading loader env vars from /efi/freebsd/loader.env Setting currdev to disk0p1: failed to allocate staging area: 9 failed to allocate staging area ## Application failed, r =3D 5 EFI LOAD FAILED: continuing... BOOTP broadcast 1 BOOTP broadcast 2 = =E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2= =80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80= =94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94= =E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94=E2= =80=94=E2=80=94=E2=80=94=E2=80=94=E2=80=94 Klaus
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?C50A9048-FA16-4238-9639-AD2F5AEF64F8>