Date: Fri, 13 Sep 2002 03:49:34 +0200 From: Dan Johansson <djodv97@student.vxu.se> To: freebsd-mobile@freebsd.org Subject: Xircom 10/100 CE3 problem Message-ID: <3D81442E.4030205@student.vxu.se>
next in thread | raw e-mail | index | archive | help
Hi, this is my first post to the list. I am having trouble with my Xircom pccard on a Dell Inspiron 7500 using FreeBSD 4.6.2. The problem is that it is not activated until late in the boot secuence so for instance nfs mounts at boot time fails. Here follows my dmesg: -------------------------------------- CPU: Pentium III/Pentium III Xeon/Celeron (501.14-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x681 Stepping = 1 Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 134152192 (131008K bytes) config> q avail memory = 126959616 (123984K bytes) Preloaded elf kernel "kernel" at 0xc038b000. Preloaded userconfig_script "/boot/kernel.conf" at 0xc038b09c. Pentium Pro MTRR support enabled md0: Malloc disk Using $PIR table, 7 entries at 0xc00fdf50 apm0: <APM BIOS> on motherboard apm: found APM BIOS v1.2, connected at v1.2 npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard pci0: <PCI bus> on pcib0 pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pci1: <ATI Mobility-1 graphics accelerator> at 0.0 irq 11 pci_cfgintr_linked: linked (60) to hard-routed irq 11 pci_cfgintr: 0:4 INTA routed to irq 11 pcic0: <TI PCI-1225 PCI-CardBus Bridge> mem 0x44000000-0x44000fff irq 11 at device 4.0 on pci0 pcic0: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][FUNC pci int + CSC serial isa irq] pccard0: <PC Card bus (classic)> on pcic0 pci_cfgintr_linked: linked (60) to hard-routed irq 11 pci_cfgintr: 0:4 INTA routed to irq 11 pcic1: <TI PCI-1225 PCI-CardBus Bridge> mem 0x44001000-0x44001fff irq 11 at device 4.1 on pci0 pcic1: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][FUNC pci int + CSC serial isa irq] pccard1: <PC Card bus (classic)> on pcic1 isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 ATA33 controller> port 0x1050-0x105f at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x1060-0x107f irq 5 at device 7.2 on pci0 usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered chip1: <Intel 82371AB Power management controller> port 0x1040-0x104f at device 7.3 on pci0 pcm0: <ESS Technology Maestro-2E> port 0x1400-0x14ff irq 5 at device 8.0 on pci0 orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: configured irq 3 not in bitmap of probed irqs 0 ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/7 bytes threshold lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 plip0: <PLIP network interface> on ppbus0 pccard: card inserted, slot 0 ad0: 6194MB <IBM-DBCA-206480> [13424/15/63] at ata0-master UDMA33 acd0: CDROM <TOSHIBA CD-ROM XM-1902B> at ata1-master PIO4 Mounting root from ufs:/dev/ad0s2a xe0 at port 0x240-0x24f iomem 0xd1000-0xd1fff irq 11 slot 0 on pccard0 xe0: Xircom CE3, bonding version 0x45, 100Mbps capable xe0: DingoID = 0x444b, RevisionID = 0x1, VendorID = 0 xe0: Ethernet address 00:10:a4:b5:49:17 module_register: module pccard/xe already exists! linker_file_sysinit "if_xe.ko" failed to register! 17 xe0: watchdog timeout; resetting card ------------------------------------------------------------------------------------ There seems to be a problem with using irq 11, but I can't change it by setting the pccardd_flags or editing pccard.conf. I guess it is because it is hard routed ? I have tried using hw.pcic.intr_path=1, hw.pcic.irq=0 (poll mode) then I can set the card to use irq 10. But the same problem remains. Also I have compiled xe into the kernel. But it still tries to load the module? Any ideas? /Dan To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3D81442E.4030205>