Date: Fri, 5 Apr 2002 02:20:23 -0600 From: Larry Rosenman <ler@lerctr.org> To: "M. Warner Losh" <imp@village.org> Cc: freebsd-mobile@FreeBSD.ORG Subject: Re: LinkSys wpc11v2.5 card: random shutdown? Message-ID: <20020405082022.GA207@lerlaptop.lerctr.org> In-Reply-To: <20020405081254.GA475@lerlaptop.lerctr.org> References: <20020405073602.GA253@lerlaptop.lerctr.org> <20020405.005827.29652885.imp@village.org> <20020405080643.GA451@lerlaptop.lerctr.org> <20020405.010944.62650820.imp@village.org> <20020405081254.GA475@lerlaptop.lerctr.org>
next in thread | previous in thread | raw e-mail | index | archive | help
* Larry Rosenman <ler@lerctr.org> [020405 02:13]:
> * M. Warner Losh <imp@village.org> [020405 02:10]:
> > Boot -v next time and lemme know if there are any additional messages
> > about power that it produces.
> >
> > It is looking for all the world like the card's power is being cut and
> > the socket isn't telling us the card was ejected.
> >
> > :-(
> Hmm. What would cause this?
> >
> > BTW, what kind of laptop is this exactly? If you said before, please
> > accpet my appology.
> I did, but here goes:
>
> Toshiba Satellite 4005CDS, with a new 30GB HDD (replacing the 4GB that
> was there), but the problem was happening before the HDD replacement.
>
> I'll run the boot -v in a minute or two, and post it's dmesg.
Here is a boot -v dmesg:
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-STABLE #1: Thu Apr 4 10:08:20 CST 2002
ler@lerlaptop:/usr/obj/usr/src/sys/LERLAPTOP
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (233.29-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x650 Stepping = 0
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 167706624 (163776K bytes)
config> q
avail memory = 159789056 (156044K bytes)
Preloaded elf kernel "kernel" at 0xc0331000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc033109c.
Pentium Pro MTRR support enabled
Using $PIR table, 4 entries at 0xc00f1330
apm0: <APM BIOS> on motherboard
apm: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX host to PCI bridge (AGP disabled)> on motherboard
pci0: <PCI bus> on pcib0
pci0: <Chips & Technologies 65555 SVGA controller> at 4.0
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xfe60-0xfe6f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 7.2 irq 11
intpm0: <Intel 82371AB Power management controller> port 0xfe70-0xfe7f irq 9 at device 7.3 on pci0
intpm0: I/O mapped fe70
intpm0: intr IRQ 9 enabled revision 0
smbus0: <System Management Bus> on intsmb0
intpm0: PM I/O mapped fe00
chip1: <Toshiba Fast Infra Red controller> port 0xff80-0xff9f irq 11 at device 10.0 on pci0
orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0
fdc0: <NEC 765 or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
pcic0: <Intel i82365SL-A/B> at port 0x3e0-0x3e1 on isa0
pcic0: Polling mode
pccard0: <PC Card bus (classic)> on pcic0
pccard1: <PC Card bus (classic)> on pcic0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
unknown: <PNP0000> can't assign resources
pca0: <AT-style speaker sound> at port 0x61 on isa0
unknown: <PNP0303> can't assign resources
unknown: <PNP0f13> can't assign resources
unknown: <PNP0c02> can't assign resources
unknown: <PNP0700> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0401> can't assign resources
unknown: <PNP0e00> can't assign resources
pcm0: <Yamaha OPL-SAx> at port 0x220-0x233,0x530-0x537,0x388-0x38f,0x330-0x333,0x538-0x539 irq 5 drq 1,0 on isa0
ata1-slave: ATAPI identify retries exceeded
pccard: card inserted, slot 1
ad0: 28615MB <FUJITSU MHN2300AT> [58140/16/63] at ata0-master UDMA33
acd0: CDROM <CD-224E> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s1a
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xffe0-0xffff irq 11 at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
wi0: <WaveLAN/IEEE 802.11> at port 0x240-0x27f irq 3 flags 0x10000 slot 1 on pccard1
wi0: 802.11 address: 00:06:25:01:da:49
wi0: using RF:PRISM2.5 MAC:ISL3873, Firmware: 1.0 variant 3
pid 570 (evolution-mail), uid 101: exited on signal 6
Waiting (max 60 seconds) for system process `vnlru' to stop...stopped
Waiting (max 60 seconds) for system process `bufdaemon' to stop...stopped
Waiting (max 60 seconds) for system process `syncer' to stop...stopped
syncing disks... 17 5 2 1
done
Uptime: 5h45m32s
Rebooting...
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-STABLE #2: Thu Apr 4 23:57:20 CST 2002
ler@lerlaptop:/usr/obj/usr/src/sys/LERLAPTOP
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (233.29-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x650 Stepping = 0
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 167706624 (163776K bytes)
config> q
avail memory = 159789056 (156044K bytes)
Preloaded elf kernel "kernel" at 0xc0331000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc033109c.
Pentium Pro MTRR support enabled
Using $PIR table, 4 entries at 0xc00f1330
apm0: <APM BIOS> on motherboard
apm: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX host to PCI bridge (AGP disabled)> on motherboard
pci0: <PCI bus> on pcib0
pci0: <Chips & Technologies 65555 SVGA controller> at 4.0
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xfe60-0xfe6f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 7.2 irq 11
intpm0: <Intel 82371AB Power management controller> port 0xfe70-0xfe7f irq 9 at device 7.3 on pci0
intpm0: I/O mapped fe70
intpm0: intr IRQ 9 enabled revision 0
smbus0: <System Management Bus> on intsmb0
intpm0: PM I/O mapped fe00
chip1: <Toshiba Fast Infra Red controller> port 0xff80-0xff9f irq 11 at device 10.0 on pci0
orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0
fdc0: <NEC 765 or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
pcic0: <Intel i82365SL-A/B> at port 0x3e0-0x3e1 on isa0
pcic0: Polling mode
pccard0: <PC Card bus (classic)> on pcic0
pccard1: <PC Card bus (classic)> on pcic0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
unknown: <PNP0000> can't assign resources
pca0: <AT-style speaker sound> at port 0x61 on isa0
unknown: <PNP0303> can't assign resources
unknown: <PNP0f13> can't assign resources
unknown: <PNP0c02> can't assign resources
unknown: <PNP0700> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0401> can't assign resources
unknown: <PNP0e00> can't assign resources
pcm0: <Yamaha OPL-SAx> at port 0x220-0x233,0x530-0x537,0x388-0x38f,0x330-0x333,0x538-0x539 irq 5 drq 1,0 on isa0
ata1-slave: ATAPI identify retries exceeded
pccard: card inserted, slot 1
ad0: 28615MB <FUJITSU MHN2300AT> [58140/16/63] at ata0-master UDMA33
acd0: CDROM <CD-224E> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s1a
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xffe0-0xffff irq 11 at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
wi0: <WaveLAN/IEEE 802.11> at port 0x240-0x27f irq 3 flags 0x10000 slot 1 on pccard1
wi0: 802.11 address: 00:06:25:01:da:49
wi0: using RF:PRISM2.5 MAC:ISL3873, Firmware: 1.0 variant 3
wi0: detached
stray irq 3
pccard: card disabled, slot 1
resumed from suspended mode (slept 00:00:14)
ata0: resetting devices .. done
ata1: resetting devices .. ata1-slave: ATAPI identify retries exceeded
done
pccard: card inserted, slot 1
wi0: <WaveLAN/IEEE 802.11> at port 0x240-0x27f irq 3 flags 0x10000 slot 1 on pccard1
wi0: 802.11 address: 00:06:25:01:da:49
wi0: using RF:PRISM2.5 MAC:ISL3873, Firmware: 1.0 variant 3
Waiting (max 60 seconds) for system process `vnlru' to stop...stopped
Waiting (max 60 seconds) for system process `bufdaemon' to stop...stopped
Waiting (max 60 seconds) for system process `syncer' to stop...stopped
syncing disks... 9 9 9 9 9 9 9 9 1 1
done
Uptime: 54m22s
Rebooting...
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-STABLE #2: Thu Apr 4 23:57:20 CST 2002
ler@lerlaptop:/usr/obj/usr/src/sys/LERLAPTOP
Calibrating clock(s) ... TSC clock: 233285825 Hz, i8254 clock: 1193172 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium II/Pentium II Xeon/Celeron (233.29-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x650 Stepping = 0
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 167706624 (163776K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00358000 - 0x09fe7fff, 164167680 bytes (40080 pages)
config> q
avail memory = 159789056 (156044K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00fbc60
bios32: Entry = 0xfc288 (c00fc288) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x1927
pnpbios: Found PnP BIOS data at 0xc00fed00
pnpbios: Entry = f0000:92c6 Rev = 1.0
pnpbios: Event flag at 510
pnpbios: OEM ID 8933f351
Other BIOS signatures found:
ACPI: 000f1140
Preloaded elf kernel "kernel" at 0xc0331000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc03310a8.
Pentium Pro MTRR support enabled
Math emulator present
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71928086)
Using $PIR table, 4 entries at 0xc00f1330
apm0: <APM BIOS> on motherboard
apm: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX host to PCI bridge (AGP disabled)> on motherboard
found-> vendor=0x8086, dev=0x7192, revid=0x02
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base e0000000, size 28
found-> vendor=0x102c, dev=0x00e5, revid=0xc6
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base fe000000, size 24
found-> vendor=0x8086, dev=0x7110, revid=0x02
class=06-80-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7111, revid=0x01
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000fe60, size 4
found-> vendor=0x8086, dev=0x7112, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=11
map[20]: type 1, range 32, base 0000ffe0, size 5
found-> vendor=0x8086, dev=0x7113, revid=0x02
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[90]: type 1, range 32, base 0000fe70, size 4
found-> vendor=0x1179, dev=0x0701, revid=0x23
class=07-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base 0000ff80, size 5
pci0: <PCI bus> on pcib0
pci0: <Chips & Technologies 65555 SVGA controller> (vendor=0x102c, dev=0x00e5) at 4.0
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xfe60-0xfe6f at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xfe60
ata0: mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ata0-master: ATA 01 a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xfe68
ata1: mask=03 ostat0=50 ostat2=01
ata1-master: ATAPI 14 eb
ata1-slave: ATAPI 14 eb
ata1: mask=03 stat0=00 stat1=01
ata1: devices=0c
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> (vendor=0x8086, dev=0x7112) at 7.2 irq 11
intpm0: <Intel 82371AB Power management controller> port 0xfe70-0xfe7f irq 9 at device 7.3 on pci0
intpm0: I/O mapped fe70
intpm0: intr IRQ 9 enabled revision 0
smbus0: <System Management Bus> on intsmb0
smbus: smb devclass not found
intpm0: PM I/O mapped fe00
chip1: <Toshiba Fast Infra Red controller> port 0xff80-0xff9f irq 11 at device 10.0 on pci0
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
pnpbios: 16 devices, largest 501 bytes
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: skipping empty range
PNP0c01: adding fixed memory32 range 0xf0000-0xfffff, size=0x10000
PNP0c01: adding fixed memory32 range 0x100000-0x9feffff, size=0x9ef0000
PNP0c01: adding fixed memory32 range 0x9ff0000-0x9ffffff, size=0x10000
PNP0c01: adding fixed memory32 range 0x100a0000-0x100fffff, size=0x60000
PNP0c01: adding fixed memory32 range 0xfff00000-0xffffffff, size=0x100000
PNP0c01: end config
pnpbios: handle 1 device ID PNP0c01 (010cd041)
PNP0200: adding io range 0-0xf, size=0x10, align=0x1
PNP0200: adding io range 0x81-0x83, size=0x3, align=0x1
PNP0200: adding io range 0x87-0x87, size=0x1, align=0x1
PNP0200: adding io range 0x89-0x8b, size=0x3, align=0x1
PNP0200: adding io range 0x8f-0x8f, size=0x1, align=0x1
PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0x1
PNP0200: adding dma mask 0x10
PNP0200: end config
pnpbios: handle 2 device ID PNP0200 (0002d041)
PNP0000: adding io range 0x20-0x21, size=0x2, align=0x1
PNP0000: adding io range 0xa0-0xa1, size=0x2, align=0x1
PNP0000: adding irq mask 00x4
PNP0000: end config
pnpbios: handle 3 device ID PNP0000 (0000d041)
PNP0100: adding io range 0x40-0x43, size=0x4, align=0x1
PNP0100: adding irq mask 00x1
PNP0100: end config
pnpbios: handle 4 device ID PNP0100 (0001d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
PNP0800: end config
pnpbios: handle 5 device ID PNP0800 (0008d041)
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0x1
PNP0c04: adding irq mask 0x2000
PNP0c04: end config
pnpbios: handle 6 device ID PNP0c04 (040cd041)
PNP0303: adding io range 0x60-0x60, size=0x1, align=0x1
PNP0303: adding io range 0x64-0x64, size=0x1, align=0x1
PNP0303: adding irq mask 00x2
PNP0303: end config
pnpbios: handle 7 device ID PNP0303 (0303d041)
PNP0f13: adding irq mask 0x1000
PNP0f13: end config
pnpbios: handle 8 device ID PNP0f13 (130fd041)
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0x1
PNP0b00: adding irq mask 0x100
PNP0b00: end config
pnpbios: handle 9 device ID PNP0b00 (000bd041)
PNP0c02: adding io range 0x80-0x80, size=0x1, align=0x1
PNP0c02: adding io range 0x84-0x86, size=0x3, align=0x1
PNP0c02: adding io range 0x88-0x88, size=0x1, align=0x1
PNP0c02: adding io range 0x8c-0x8e, size=0x3, align=0x1
PNP0c02: adding io range 0xe0-0xef, size=0x10, align=0x1
PNP0c02: adding io range 0xb0-0xb2, size=0x3, align=0x1
PNP0c02: adding io range 0x2e-0x2f, size=0x2, align=0x1
PNP0c02: adding io range 0x62-0x62, size=0x1, align=0x1
PNP0c02: adding io range 0x66-0x66, size=0x1, align=0x1
PNP0c02: adding io range 0x6d-0x6d, size=0x1, align=0x1
PNP0c02: adding io range 0x6f-0x6f, size=0x1, align=0x1
PNP0c02: adding io range 0x480-0x48f, size=0x10, align=0x1
PNP0c02: adding io range 0xcf8-0xcff, size=0x8, align=0x1
PNP0c02: adding io range 0x4d0-0x4d1, size=0x2, align=0x1
PNP0c02: adding io range 0x22-0x22, size=0x1, align=0x1
PNP0c02: adding io range 0x92-0x92, size=0x1, align=0x1
PNP0c02: adding io range 0xfeac-0xfeac, size=0x1, align=0x1
PNP0c02: adding io range 0xfe00-0xfe3f, size=0x40, align=0x1
PNP0c02: adding io range 0xfe50-0xfe57, size=0x8, align=0x1
PNP0c02: adding io range 0xfe70-0xfe7f, size=0x10, align=0x1
PNP0c02: adding io range 0xfe90-0xfe97, size=0x8, align=0x1
PNP0c02: adding io range 0xfe9e-0xfe9e, size=0x1, align=0x1
PNP0c02: adding irq mask 0x200
PNP0c02: end config
pnpbios: handle 10 device ID PNP0c02 (020cd041)
PNP0700: adding io range 0x3f2-0x3f5, size=0x4, align=0x1
PNP0700: adding io range 0x3f7-0x3f7, size=0x1, align=0x1
PNP0700: adding irq mask 0x40
PNP0700: adding dma mask 0x4
PNP0700: end config
pnpbios: handle 11 device ID PNP0700 (0007d041)
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0x1
PNP0501: adding irq mask 0x10
PNP0501: end config
pnpbios: handle 14 device ID PNP0501 (0105d041)
PNP0401: adding io range 0x378-0x37a, size=0x3, align=0x1
PNP0401: adding io range 0x778-0x77a, size=0x3, align=0x1
PNP0401: adding irq mask 0x80
PNP0401: adding dma mask 0x8
PNP0401: end config
pnpbios: handle 16 device ID PNP0401 (0104d041)
PNP0a03: end config
pnpbios: handle 17 device ID PNP0a03 (030ad041)
PNP0e00: adding io range 0x3e0-0x3e1, size=0x2, align=0x1
PNP0e00: adding irq mask 0000
PNP0e00: end config
pnpbios: handle 19 device ID PNP0e00 (000ed041)
YMH0021: adding io range 0x220-0x233, size=0x14, align=0x1
YMH0021: adding io range 0x530-0x537, size=0x8, align=0x1
YMH0021: adding io range 0x388-0x38f, size=0x8, align=0x1
YMH0021: adding io range 0x330-0x333, size=0x4, align=0x1
YMH0021: adding io range 0x538-0x539, size=0x2, align=0x1
YMH0021: adding irq mask 0x20
YMH0021: adding dma mask 0x2
YMH0021: adding dma mask 0x1
YMH0021: end config
pnpbios: handle 21 device ID YMH0021 (2100a865)
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0
fdc0: <NEC 765 or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata2 failed to probe at port 0x1f0 irq 14 on isa0
ata3 failed to probe at port 0x170 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:4
psm0: syncmask:08, syncbits:08
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 05 50 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic0: <Intel i82365SL-A/B> at port 0x3e0-0x3e1 on isa0
pcic0: Polling mode
pccard0: <PC Card bus (classic)> on pcic0
pccard1: <PC Card bus (classic)> on pcic0
pcic1: Cannot get I/O range
pcic1 failed to probe at port 0x3e0-0x3e1 on isa0
sio0: irq maps: 0x41 0x51 0x51 0x51
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
isa_probe_children: probing PnP devices
unknown: <PNP0c01> failed to probe at iomem 0-0x9ffff,0xf0000-0xfffff,0x100000-0x9feffff,0x9ff0000-0x9ffffff,0x100a0000-0x100fffff,0xfff00000-0xffffffff on isa0
unknown: <PNP0200> failed to probe at port 0-0xf,0x81-0x83,0x87,0x89-0x8b,0x8f,0xc0-0xdf drq 4 on isa0
unknown: <PNP0000> can't assign resources
unknown: <PNP0000> at port 0x20-0x21,0xa0-0xa1 irq 2 on isa0
unknown: <PNP0100> failed to probe at port 0x40-0x43 irq 0 on isa0
pca0: <AT-style speaker sound> at port 0x61 on isa0
unknown: <PNP0c04> failed to probe at port 0xf0-0xff irq 13 on isa0
unknown: <PNP0303> can't assign resources
unknown: <PNP0303> at port 0x60 on isa0
unknown: <PNP0f13> can't assign resources
unknown: <PNP0f13> at irq 12 on isa0
unknown: <PNP0b00> failed to probe at port 0x70-0x71 irq 8 on isa0
unknown: <PNP0c02> can't assign resources
unknown: <PNP0c02> at port 0x80,0x84-0x86,0x88,0x8c-0x8e,0xe0-0xef,0xb0-0xb2,0x2e-0x2f,0x62,0x66,0x6d,0x6f,0x480-0x48f,0xcf8-0xcff,0x4d0-0x4d1,0x22,0x92,0xfeac,0xfe00-0xfe3f,0xfe50-0xfe57,0xfe70-0xfe7f on isa0
unknown: <PNP0700> can't assign resources
unknown: <PNP0700> at port 0x3f2-0x3f5 on isa0
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNP0401> can't assign resources
unknown: <PNP0401> at port 0x378-0x37a on isa0
unknown: <PNP0a03> failed to probe on isa0
unknown: <PNP0e00> can't assign resources
unknown: <PNP0e00> at port 0x3e0-0x3e1 on isa0
pcm0: <Yamaha OPL-SAx> at port 0x220-0x233,0x530-0x537,0x388-0x38f,0x330-0x333,0x538-0x539 irq 5 drq 1,0 on isa0
Yamaha: ver 0x21 DMA config 0x85
pcm: setmap 4000, 1000; 0xc8d1b000 -> 4000
pcm: setmap 5000, 1000; 0xc8d1c000 -> 5000
BIOS Geometries:
0:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
ata1-slave: ATAPI identify retries exceeded
pccard: card inserted, slot 1
pcic0: reset 1 int is 0 stat is ff
ad0: success setting UDMA2 on Intel chip
Creating DISK ad0
pcic0: reset 2 int is 60 stat is cf
ar: FreeBSD check1 failed
ad0: <FUJITSU MHN2300AT/7256> ATA-5 disk at ata0-master
ad0: 28615MB (58605120 sectors), 58140 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=5 cblid=1
ata1-master: piomode=4 dmamode=2 udmamode=-1 dmaflag=1
ata1-master: success setting PIO4 on generic chip
acd0: <CD-224E/7.5A> CDROM drive at ata1 as master
acd0: read 4134KB/s (34515KB/s), 128KB buffer, PIO4
acd0: Reads: CD-R, CD-DA stream
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
Mounting root from ufs:/dev/ad0s1a
ad0s1: type 0xa5, start 63, end = 58605119, size 58605057 : OK
start_init: trying /sbin/init
pcic0: reset 3 int is 60 stat is ef
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xffe0-0xffff irq 11 at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Linux ELF exec handler installed
pccard1: Assigning wi0: io 0x240-0x27f irq 3 mem 0x0-0xffffffff
pcic: I/O win 0 flags 15 240-27f
pcic: I/O win 0 flags 5 240-27f
wi0: <WaveLAN/IEEE 802.11> at port 0x240-0x27f irq 3 flags 0x10000 slot 1 on pccard1
pcic: I/O win 0 flags 15 240-27f
wi0: 802.11 address: 00:06:25:01:da:49
wi0: using RF:PRISM2.5 MAC:ISL3873, Firmware: 1.0 variant 3
wi0: wi_generic_attach:wi_has_wep = 1
bpf: wi0 attached
--
Larry Rosenman http://www.lerctr.org/~ler
Phone: +1 972-414-9812 E-Mail: ler@lerctr.org
US Mail: 1905 Steamboat Springs Drive, Garland, TX 75044-6749
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020405082022.GA207>