Date: Fri, 20 Jun 2003 13:59:39 -0700 (PDT) From: Claudiu Bichir <claudiubichir@yahoo.com> To: freebsd-questions@freebsd.org Subject: RE:MODEM Message-ID: <20030620205939.46063.qmail@web41315.mail.yahoo.com>
next in thread | raw e-mail | index | archive | help
I have an Aztech UM9800 external modem but I don't know how to
configure it to work with FreeBSD.When my system boots I see
something like "ugen0:SMElectronics Communicator bla bla", I think
this is my modem ...
If anybody would like to help me configuring my modem to work with
FreeBSD I would appreciate that. I cannot use ppp ...
after I type "set device /dev/ugen0","set speed 115200","enable dns"
and "term" it says something like ... "ugenpoll: no edesc"(two times),
don't know why.
There is also a dial-up tool in KDE 3.0 but after I hit "Connect"
the whole system doesn't respond anymore and I must reboot it.
I hope my modem works with freebsd.
dmesg:
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-RELEASE #0: Fri Jun 20 20:55:07 EEST 2003
root@BSD:/usr/src/sys/i386/compile/BICHIR
Preloaded elf kernel "/boot/kernel/kernel" at 0xc04d0000.
Preloaded elf module "/boot/kernel/snd_via82c686.ko" at 0xc04d00a8.
Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc04d015c.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc04d0208.
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 949972222 Hz
CPU: AMD Athlon(tm) Processor (949.97-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x642 Stepping = 2
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
AMD Features=0xffffffffc0440000<RSVD,AMIE,DSP,3DNow!>
real memory = 268369920 (255 MB)
avail memory = 255696896 (243 MB)
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <VIA694 AWRDACPI> on motherboard
ACPI-0625: *** Info: GPE Block0 defined as GPE0 to GPE15
Using $PIR table, 7 entries at 0xc00fddc0
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-safe" frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0x6000-0x607f,0x5000-0x500f,0x4080-0x40ff,0x4000-0x407f,0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <VIA 82C8363 (Apollo KT133A) host to PCI bridge> mem 0xd8000000-0xdbffffff at device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA100 controller> port 0xd000-0xd00f at device 7.1 on pci0
atapci0: Correcting VIA config for southbridge data corruption bug
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 9 at device 7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ugen0: STMicroelectronics USB Communicator, rev 1.00/2.00, addr 2
ulpt0: Hewlett-Packard DeskJet 3820, rev 1.10/1.00, addr 3, iclass 7/1
ulpt0: using bi-directional mode
uhci1: <VIA 83C572 USB controller> port 0xd800-0xd81f irq 9 at device 7.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
pci0: <bridge, PCI-unknown> at device 7.4 (no driver attached)
pcm0: <VIA VT82C686A> port 0xe400-0xe403,0xe000-0xe003,0xdc00-0xdcff irq 10 at device 7.5 on pci0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0 port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
orm0: <Option ROM> at iomem 0xcc000-0xcffff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
acpi_cpu: CPU throttling enabled, 2 steps from 100% to 50.0%
ad0: DMA limited to UDMA33, non-ATA66 cable or device
ad0: 19595MB <QUANTUM FIREBALLP AS20.5> [39813/16/63] at ata0-master UDMA33
acd0: CDROM <54X CD-ROM> at ata0-slave PIO4
acd1: CD-RW <MSI CD-RW MS-8348> at ata1-slave PIO4
Mounting root from ufs:/dev/ad0s2a
<----------------dmesg end---------------->
#################################################################
# PPP Sample Configuration File
# Originally written by Toshiharu OHNO
# Simplified 5/14/1999 by wself@cdrom.com
#
# See /usr/share/examples/ppp/ for some examples
#
# $FreeBSD: src/etc/ppp/ppp.conf,v 1.8 2001/06/21 15:42:26 brian Exp $
#################################################################
default:
set log Phase Chat LCP IPCP CCP tun command
ident user-ppp VERSION (built COMPILATIONDATE)
# Ensure that "device" references the correct serial port
# for your modem. (cuaa0 = COM1, cuaa1 = COM2)
#
set device /dev/cuaa1
set speed 115200
set dial "ABORT BUSY ABORT NO\\sCARRIER TIMEOUT 5 \
\"\" AT OK-AT-OK ATE1Q0 OK \\dATDT\\T TIMEOUT 40 CONNECT"
set timeout 180 # 3 minute idle timer (the default)
enable dns # request DNS info (for resolv.conf)
papchap:
#
# edit the next three lines and replace the items in caps with
# the values which have been assigned by your ISP.
#
set phone
set authname
set authkey
set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0
add default HISADDR # Add a (sticky) default route
<---------------ppp.conf end--------------->
# -- sysinstall generated deltas -- # Fri Jun 20 20:36:25 2003
# Created: Fri Jun 20 20:36:25 2003
# Enable network daemons for user convenience.
# Please make all changes to this file, not to /etc/defaults/rc.conf.
# This file now contains just the overrides from /etc/defaults/rc.conf.
font8x14="/usr/share/syscons/fonts/iso15-8x14.fnt"
font8x16="/usr/share/syscons/fonts/iso15-8x16.fnt"
font8x8="/usr/share/syscons/fonts/iso15-8x8.fnt"
hostname="BSD"
kern_securelevel_enable="NO"
linux_enable="YES"
moused_enable="YES"
scrnmap="NO"
sendmail_enable="NO"
sshd_enable="YES"
usbd_enable="YES"
<---------------rc.conf end--------------->
Thank you,
Claudiu.
---------------------------------
Do you Yahoo!?
SBC Yahoo! DSL - Now only $29.95 per month!
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20030620205939.46063.qmail>