Date: Sun, 13 Nov 2011 18:14:13 -0800 From: YongHyeon PYUN <pyunyh@gmail.com> To: rank1seeker@gmail.com Cc: freebsd-acpi@freebsd.org, hackers@freebsd.org Subject: Re: Adventure into S3 state and back Message-ID: <20111114021413.GA1709@michelle.cdnetworks.com> In-Reply-To: <20111112.144149.725.1@DOMY-PC> References: <20111110.182948.630.1@DOMY-PC> <20111112002727.GD17792@michelle.cdnetworks.com> <20111112.144149.725.1@DOMY-PC>
next in thread | previous in thread | raw e-mail | index | archive | help
On Sat, Nov 12, 2011 at 03:41:49PM +0100, rank1seeker@gmail.com wrote: > ----- Original Message ----- > From: YongHyeon PYUN <pyunyh@gmail.com> > To: rank1seeker@gmail.com > Cc: hackers@freebsd.org, freebsd-acpi@freebsd.org > Date: Fri, 11 Nov 2011 16:27:27 -0800 > Subject: Re: Adventure into S3 state and back > > > On Thu, Nov 10, 2011 at 07:29:48PM +0100, rank1seeker@gmail.com wrote: > > > 8.2-p4 RELEASE amd64 > > > > > > I've built a custom kernel, only with drivers, that I need > > > After resuming from S3 ... > > > > > > I hit: > > > # ifconfig > > > and all hells breaks loose: > > > ---- > > > bge0: PHY read timed out (phy 1, reg 5, val 0xffffffff) > > > bge0: PHY read timed out (phy 1, reg 10, val 0xffffffff) > > > bge0: PHY read timed out (phy 1, reg 25, val 0xffffffff) > > > media: Ethernet autoselect > > > status: no carrier > > > bge0: PHY read timed out (phy 1, reg 1, val 0xffffffff) > > > bge0: PHY read timed out (phy 1, reg 1, val 0xffffffff) > > > bge0: PHY read timed out (phy 1, reg 0, val 0xffffffff) > > > ugen3.2: <Logitech> at usbus3 (disconnected) > > > ukbd0: at uhub3, port 1, addr 2 (disconnected) > > > ums0: at uhub3, port 1, addr 2 (disconnected) > > > uhid0: at uhub3, port 1, addr 2 (disconnected) > > > bge0: PHY read timed out (phy 1, reg 4, val 0xffffffff) > > > ugen3.2: <Logitech> at usbus3 > > > ukbd0: <Logitech USB Receiver, class 0/0, rev 2.00/12.01, addr 2> on > usbus3 > > > kbd2 at ukbd0 > > > ums0: <Logitech USB Receiver, class 0/0, rev 2.00/12.01, addr 2> on > usbus3 > > > ums0: 16 buttons and [XYZT] coordinates ID=2 > > > uhid0: <Logitech USB Receiver, class 0/0, rev 2.00/12.01, addr 2> on > usbus3 > > > bge0: PHY read timed out (phy 1, reg 5, val 0xffffffff) > > > bge0: PHY read timed out (phy 1, reg 10, val 0xffffffff) > > > bge0: PHY read timed out (phy 1, reg 25, val 0xffffffff) > > > pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152 > > > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 > > > options=3<RXCSUM,TXCSUM> > > > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3 > > > inet6 ::1 prefixlen 128 > > > inet 127.0.0.1 netmask 0xff000000 > > > nd6 options=3<PERFORMNUD,ACCEPT_RTADV> > > > cruiser# ifconfig > > > bge0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 > > > > options=8009b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,LINKSTATE> > > > ether 00:21:70:70:01:df > > > bge0: PHY read timed out (phy 1, reg 1, val 0xffffffff) > > > bge0: PHY read timed out (phy 1, reg 1, val 0xffffffff) > > > > > > ... ... ... <You get the point> > > > > Known issue. kern/136876. > > Mobile bge(4) controllers seem to have this issue. > > I can see this has been reported, when 8.0-BETA1 was released. > Now is almost 8.3 out and problem is still present Actually I spent a lot of time to address this but all attempts failed mainly because I have no access to such bge(4) controllers. Remote debugging does not work for suspend/resume issues so chances would be low to get it fixed in near future unless someone donate problematic hardwares to me.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20111114021413.GA1709>