Date: Sat, 02 Jul 2011 15:23:30 +0300 From: Tarick <tungan@ukr.net> To: freebsd-arm@freebsd.org Subject: Re: Few issues with Marvell code Message-ID: <1309609410.2450.9.camel@KLH.if.ua> In-Reply-To: <20110701120021.6768D10656E9@hub.freebsd.org> References: <20110701120021.6768D10656E9@hub.freebsd.org>
next in thread | previous in thread | raw e-mail | index | archive | help
> --------------------------------------------------------------------- > > Message: 1 > Date: Fri, 1 Jul 2011 02:25:45 +0200 > From: Damjan Marion <damjan.marion@gmail.com> > Subject: Re: Few issues with Marvell code > To: Kevin Lo <kevlo@kevlo.org> > Cc: freebsd-arm@freebsd.org > Message-ID: <6F62AF96-4631-4F97-80CF-959A6C373446@gmail.com> > Content-Type: text/plain; charset=us-ascii > > > On Jun 29, 2011, at 11:59 AM, Kevin Lo wrote: > > > > > I tried to boot kernel.bin used the generic DB-88F5XXX kernel > > configuration on the 88F5182 board, it doesn't work either. > > I will further investigate. > > Where it stops? > > Damjan > > > ------------------------------ > > Message: 2 > Date: Fri, 01 Jul 2011 14:42:55 +0800 > From: Kevin Lo <kevlo@kevlo.org> > Subject: Re: Few issues with Marvell code > To: Damjan Marion <damjan.marion@gmail.com> > Cc: freebsd-arm@freebsd.org > Message-ID: <1309502575.7757.2.camel@srgsec> > Content-Type: text/plain; charset="Big5" > > On Fri, 2011-07-01 at 02:25 +0200, Damjan Marion wrote: > > On Jun 29, 2011, at 11:59 AM, Kevin Lo wrote: > > > > > > > > I tried to boot kernel.bin used the generic DB-88F5XXX kernel > > > configuration on the 88F5182 board, it doesn't work either. > > > I will further investigate. > > > > Where it stops? > > === BUFFALO LS-GL U-Boot. === > ** LOADER ** > ** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE > > U-Boot 1.1.1 (Jun 12 2006 - 10:32:00) Marvell version: 1.10.8 > > DRAM CS[0] base 0x00000000 size 128MB > DRAM Total size 128MB > [256kB@fffc0000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = > 0x00000000B > Flash: 256 kB > Addresses 20M - 0M are saved for the U-Boot usage. > Mem malloc Initialization (20M - 16M): Done > > Soc: 88F5182 > A2 > CPU: ARM926 (Rev 0) running @ > 400Mhz > Orion 1 streaming > disabled > SysClock = 200Mhz , TClock = > 166Mhz > > > USB 0: host > mode > USB 1: host > mode > PCI 0: PCI Express Root Complex > Interface > PCI 1: Conventional PCI, speed = > 33000000 > Net: egiga0 > [PRIME] > > Marvell Serial ATA > Adapter > Intergrated Sata device > found > > <<can_not_mount>> > HDD is not > found > hit any key to switch tftp > boot. > Hit any key to stop autoboot: > 0 > Marvell>> tftpboot 900000 > mv5281/kernel.bin > Using egiga0 > device > TFTP from server 172.16.113.84; our IP address is > 172.16.113.8 > Filename > 'mv5281/kernel.bin'. > Load address: > 0x900000 > Loading: > ################################################################# > > ################################################################# > > ################################################################# > > ################################################################# > > ################################################################# > > ################################################################# > > ################################################################# > > ################################################################# > > ################################################################# > > ################################# > done > Bytes transferred = 3162744 (304278 > hex) > Marvell>> go > 900000 > ## Starting application at > 0x00900000 ... > > Scary, eh? > > > Damjan > > Kevin Sorry, I messed up with the subject line, so re-posting again. Please look at http://www.freebsd.org/cgi/query-pr.cgi?pr=arm%2F156814&cat= I have OpenRD Ultimate, which is actually from DB-88F6XXX, but the kernel from current failed to load with the same message. Using the patch from PR I was able to boot successfully.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1309609410.2450.9.camel>