Date: Mon, 24 Sep 2012 10:52:51 -0400 From: Jason Keltz <jas@cse.yorku.ca> To: "freebsd-scsi@freebsd.org" <freebsd-scsi@freebsd.org> Subject: 9.1-rc1 mps timeout error Message-ID: <506073C3.7020401@cse.yorku.ca> In-Reply-To: <5050E7C7.5030607@cse.yorku.ca> References: <5050E7C7.5030607@cse.yorku.ca>
next in thread | previous in thread | raw e-mail | index | archive | help
(somewhat) Related to my previous message.... I have a system which has an Intel S3000AH server board with an LSI 9211-8i card with SAS2008 chipset, running IT firmware. It is connected to an older Chenbro CK12803 expander card which is connected to the 16 disk ports in an AIC RMC3E2-XPSS 3U chassis. At this time, I have only 12 SATA disks in the system ( 1 x 1 TB, 11 x 2 TB). The disks are all recognized, although interestingly enough, all of them report ENC SLOT 0 on the 9211-8i bios display of disks. At the end of the 9.1 boot sequence, I see: mps0: mpssas_scsiio_timeout checking sc 0xffffff8000759000 cm 0xffffff8000784380 (probe19:mps0:0:19:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 length 0 SMID 240 command timeout cm 0xffffff8000784380 ccb 0xfffffe0006918000 mps0: mpssas_alloc_tm freezing simq mps0: timedout cm 0xffffff8000784380 allocated tm 0xffffff8000771148 (probe19:mps0:0:19:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 length 0 SMID 240 completed timedout cm 0xffffff8000784380 ccb 0xfffffe0006918000 during recovery ioc 8048 scsi 0 state c xfer 0 (noperiph:mps0:0:19:0): SMID 1 abort TaskMID 240 status 0x0 code 0x0 count 1 (noperiph:mps0:0:19:0): SMID 1 finished recovery after aborting TaskMID 240 mps0: mpssas_free_tm releasing simq I'm wondering if this is something to be concerned about? Output of "camcontrol devlist" is: <CHENBRO SASX28 B1 AA11> at scbus0 target 19 lun 0 (ses0,pass0) <ATA WDC WD1002FAEX-0 1D05> at scbus0 target 25 lun 0 (pass1,da0) <ATA WDC WD2002FAEX-0 1D05> at scbus0 target 26 lun 0 (pass2,da1) <ATA WDC WD2002FAEX-0 1D05> at scbus0 target 27 lun 0 (pass3,da2) <ATA WDC WD2002FAEX-0 1D05> at scbus0 target 28 lun 0 (pass4,da3) <ATA WDC WD2002FAEX-0 1D05> at scbus0 target 29 lun 0 (pass5,da4) <ATA WDC WD2002FAEX-0 1D05> at scbus0 target 30 lun 0 (pass6,da5) <ATA WDC WD2002FAEX-0 1D05> at scbus0 target 31 lun 0 (pass7,da6) <ATA WDC WD2002FAEX-0 1D05> at scbus0 target 32 lun 0 (pass8,da7) <ATA WDC WD2002FAEX-0 1D05> at scbus0 target 33 lun 0 (pass9,da8) <ATA WDC WD2002FAEX-0 1D05> at scbus0 target 34 lun 0 (pass10,da9) <ATA WDC WD2002FAEX-0 1D05> at scbus0 target 35 lun 0 (pass11,da10) <ATA WDC WD2002FAEX-0 1D05> at scbus0 target 36 lun 0 (pass12,da11) <SONY CD-RW CRX850E 5YK3> at scbus1 target 0 lun 0 (pass13,cd0) ... I'm guessing the above error is talking to the Chenbro expander card. (mps0:0:19?) At this point, I've been ignoring the error, but if I can add a bit somewhere to make it go away, it would be even better. Thanks for any assistance.. Jason.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?506073C3.7020401>