From owner-freebsd-hackers  Wed Nov  8  7:56: 2 2000
Delivered-To: freebsd-hackers@freebsd.org
Received: from kaon.intercom.com (kaon.intercom.com [198.143.3.30])
	by hub.freebsd.org (Postfix) with ESMTP
	id 3EE6037B4C5; Wed,  8 Nov 2000 07:55:56 -0800 (PST)
Received: from [198.143.3.26] (helo=intercom.com)
	by kaon.intercom.com with esmtp (Exim 3.16 #1)
	id 13tXZg-000HYP-00; Wed, 08 Nov 2000 10:55:44 -0500
Date: Wed, 8 Nov 2000 10:55:44 -0500 (EST)
From: "Jason J. Horton" <jason@intercom.com>
X-Sender: mail@kaon.intercom.com
To: oneflower <oneflower@china.com>
Cc: freebsd-hackers@freebsd.org, freebsd-isp@freebsd.org
Subject: Re: a problem about install freebsd 4.1.1 on HP Lpr?
In-Reply-To: <001701c04991$87ea03c0$656e6dca@oneflower>
Message-ID: <Pine.BSF.4.21.0011081048510.53944-100000@kaon.intercom.com>
MIME-Version: 1.0
Content-Type: TEXT/PLAIN; charset=US-ASCII
Sender: owner-freebsd-hackers@FreeBSD.ORG
Precedence: bulk
X-Loop: FreeBSD.ORG

I've had no problems with my LPrs during installs, I have almost the same
config as you (the diff being faster CPUs). Are you sure you properly
terminated the built-in SCSI card when you installed the RAID card? The
instructions that came with the RAID card are pretty detailed in what
needs to be done. Also, if you dont have any drives attached to the
built-in SCSI card, you may want to concider disabling it in the BIOS.

> Hello,every one:
> 
>   I have meet a problem when I am installing FreeBSD 4.1.1 on HP LPR.
> 
> HP LPR:
> 
> cpu: PIII 650MHZ *2
> memory:384MB
> Disk : 9G scsi-2 *2
> Scsi card:  HP NetRaid 1si
>             scsi card without raid (HP)
> 
> PhoenixBIOS 4.06.34 PR
> Symbios,Inc.SDMS (TM) v4.0 PCI SCSI BIOS,PCI Rev. 2.0 ,2.1
> Copyright 1995 ,1998 Symbios,Inc.
> PCI-4.14.04
> 
> Symbios,Inc.Pci boot Rom ,no supported devices found.
> 
> HP NetRAID Adapter BIOS VER B.02.02 Apr 03,2000
> Copyright(c) American MegaTrends,Inc.
> 
> 
> 
> the install process stop at this screen:
> 
> "..........................................
> fxp0:<Inter pro 10/100B/100+ Ethernet> port 0x9400-0x943f mem 0xfa100000-0xfa1fffff,
> 0xfa200000-0xfa2fffff  irq 11 at device 3.0 on pci1
> fxp0: Ethernet address 00:d0:b7:91:20:d2
> sym0: <895> port 0x9000-0x90ff mem 0xfa201000-0xfa201fff,0xfa202000-0xfa2020ff 
> irq 15 at device 4.0 on pci1"
>   
> 
> after a long time ,it repeated messages on screen like :
> 
> ".......
> (noperiph: sym0:0:-1:-1): SCSI BUS mode change from SE to SE
> sym0:0:iph:sym OUT phase after..........."
> 
> 
> 
> What problem? Who can help me?
> 
> The Lpr can be installed with windows 2000 Adv Server,run well but
> boot windows needs a lot of time.
> I can't install  Redhat 7.0 on it ,too.
> It stoped at load scsi driver.
> 
> 
> Best Regards,
> 
>                                            Flower



To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hackers" in the body of the message