From owner-freebsd-questions Thu Apr 20 15:31:12 1995 Return-Path: questions-owner Received: (from majordom@localhost) by freefall.cdrom.com (8.6.10/8.6.6) id PAA12314 for questions-outgoing; Thu, 20 Apr 1995 15:31:12 -0700 Received: from halon.sybase.com (halon.sybase.com [192.138.151.33]) by freefall.cdrom.com (8.6.10/8.6.6) with SMTP id PAA12307 for ; Thu, 20 Apr 1995 15:31:10 -0700 Received: from sybase.com (sybgate.sybase.com) by halon.sybase.com (5.0/SMI-SVR4/SybFW4.0) id AA16115; Thu, 20 Apr 1995 15:22:33 -0700 Received: from red_oak.sybgate.sybase.com by sybase.com (4.1/SMI-4.1/SybH3.4) id AA12269; Thu, 20 Apr 95 15:16:54 PDT Received: by red_oak.sybgate.sybase.com (4.1/SMI-4.1/SybEC3.2) id AA12006; Thu, 20 Apr 95 18:16:52 EDT Date: Thu, 20 Apr 95 18:16:52 EDT From: jeffa@sybase.com (Jeff Anuszczyk) Message-Id: <9504202216.AA12006@red_oak.sybgate.sybase.com> To: questions@FreeBSD.org Subject: Questions/problems installing 950412 SNAP content-length: 0 Sender: questions-owner@FreeBSD.org Precedence: bulk Anyone have any ideas on how I should proceed? I'm pretty sure it's not a corrupted disk or anything (I gunzip'd and untar'd it all without a problem). Hmmm, recent discussion about the ep0 driver indicates failure to probe at 0x300. That's where my SMC card is located... do you think that could have anything to do with it? Any help or suggestions would be creately appreciated. - Jeff ----- Begin Included Message ----- >From jeffa Tue Apr 18 22:28:11 1995 From: jeffa (Jeff Anuszczyk) Subject: Questions/problems installing 950412 SNAP To: freebsd-current@freebsd.org Date: Tue, 18 Apr 95 22:28:05 EDT Cc: jeffa (Jeff Anuszczyk) Hi All, I finally finished downloading the latest SNAP and started to install it. First I made the install disks using dd. Then I booted the floppies and did a "normal" install. About the only things to note are: two SCSI disks (entire disk is used), the primary disk uses all partitions (a,e,f, g,h) for filesystems plus b for swap. I then had a devil of a time booting from the main system disk (recently running 2.0R). I needed to rewrite the boot block a bunch of times before it finally "took". When it failed the system was just booting (the primary booter is loading /kernel). The first 3 of the spining bars printed and then nothing. In any case, I got around this and the system started to boot. At this point the system is probed and promptly crashes with a fatal trap 12. I rebooted and select -c to look at what it was probing. This is were things started to get weird. It turns out that there are four entries marked enabled but has device names of zero/one as follows: Device Port irq drq iomem iosize unit flags enabled fdc0 0x3f0 6 2 0x0 0 0 0x0 Yes . . . aha0 0x330 -1 5 0x0 0 0 0x0 Yes aic0 0x340 11 -1 0x0 0 0 0x0 Yes 0 0x1f88 10 -1 0x0 0 0 0x0 Yes 1 0x350 5 -1 0x0 0 1 0x0 Yes sea0 0x0 5 -1 0xc8000 8192 0 0x0 Yes . . . ze0 0x300 10 -1 0xd8000 0 0 0x0 Yes zp0 0x300 10 -1 0xd8000 0 0 0x0 Yes 0 0xffffffff -1 -1 0x0 0 0 0x0 Yes 0 0xf0 13 -1 0x0 0 0 0x0 Yes I've edited some of the less than important stuff. The problem started immediately after the probe of aic0. The system got the fatal trap 12 and halted. I did a "disable 0" & "disable 1" and the system would now continue to just after the probe of zp0 when it then traped out again. The problem is I can't disable these additional "0" devices since the assumption of the code is a device name is unique. Any suggestions? In case anyone is curious, here is the trap. I suspect you won't need it... but better safe than sorry. This is with all devices enabled: st0(aha0:6:0): Sequential-Access density code 0x8c, drive empty aic0 not found at 0x340 Fatal Trap 12: page fault while in kernel mode fault virtual address = 0x431f4a30 fault code = supervisor read, page not present instruction pointer = 0x8:0xf01c69a4 code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, def32 1, gran 1 processor eflags = interrupt enabled, resume, IOPL = 0 current process = 0 () interrupt mask = net tty bio panic: page fault The system is an AMD DX2/80, 16MB, VLB/ISA Adaptec 1542B, 1GB SCSI-2 (DEC), Archive Python Tape SMC Elite16T This configuration worked fine under 1.1.5.1 & 2.0R. Thanks for any help anyone can offer! - Jeff ----- End Included Message -----