Date: Fri, 23 May 2008 18:10:06 GMT From: Lev Serebryakov <lev@serebryakov.spb.ru> To: freebsd-net@FreeBSD.org Subject: Re: kern/121298: [em] [panic] Fatal trap 12: page fault while in kernel mode (em0 taskq) Message-ID: <200805231810.m4NIA69U061540@freefall.freebsd.org>
next in thread | raw e-mail | index | archive | help
The following reply was made to PR kern/121298; it has been noted by GNATS. From: Lev Serebryakov <lev@serebryakov.spb.ru> To: bug-followup@FreeBSD.org, admin@aknet.ru Cc: Subject: Re: kern/121298: [em] [panic] Fatal trap 12: page fault while in kernel mode (em0 taskq) Date: Fri, 23 May 2008 21:47:41 +0400 Hello, bug-followup. I've got very similar panic. `csup' from local (located in same segment) cvsup server via gigabit link and RAID5 (geom_raid5) synchronize newely-created array with 4 disks. csup writes on OTHER disk, not included in array. No crashdump, because core was not saved: machine hangs up right after panic message, without attempts to save dump or reboot. Crash dumps are enabled and I got previous one (other bug), but in this case no dumps, no reaction on keyboards, etc. Need to reboot with pwoer switch :( ==================== panic message, typed by hands em0: watchdog timeout -- resetting kernel trap 12 with interrupts disabled Fatal trap 12: page fault in kernnel mode cpuid = 1; apic id = 01 fault virtual addewaa = 0x28 fault code = supervisor read data, page not present instruction pointer = 0x8:0xffffffff80282c2f stack pointer = 0x10:0xffffffffabed4b20 frame pointer = 0x10:0xffffff00010c9000 code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, long 1, def32 0, gran 1 processor efalgs = resume, IOPL = 1 current process = 23 (em0 taskq) trap number = 12 panic: page fault cpuid = 1 ==================== panic message, typed by hands ========================================= uname -a FreeBSD blob.home.serebryakov.spb.ru 7.0-STABLE FreeBSD 7.0-STABLE #0: Mon May 19 21:26:08 MSD 2008 lev@blob.home.serebryakov.spb.ru:/usr/obj/usr/src/sys/BLOB amd64 ========================================= uname -a ============================================ dmesg Copyright (c) 1992-2008 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.0-STABLE #0: Mon May 19 21:26:08 MSD 2008 lev@blob.home.serebryakov.spb.ru:/usr/obj/usr/src/sys/BLOB Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Core(TM)2 Duo CPU E4500 @ 2.20GHz (2200.09-MHz K8-class CPU) Origin = "GenuineIntel" Id = 0x6fd Stepping = 13 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0xe39d<SSE3,RSVD2,MON,DS_CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM> AMD Features=0x20100800<SYSCALL,NX,LM> AMD Features2=0x1<LAHF> Cores per package: 2 usable memory = 6364114944 (6069 MB) avail memory = 6141857792 (5857 MB) ACPI APIC Table: <A_M_I_ OEMAPIC > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0 <Version 2.0> irqs 0-23 on motherboard kbd1 at kbdmux0 acpi0: <A_M_I_ OEMXSDT> on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, cfd00000 (3) failed Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 Timecounter "HPET" frequency 14318180 Hz quality 900 cpu0: <ACPI CPU> on acpi0 ACPI Warning (tbutils-0243): Incorrect checksum in table [OEMB] - 51, should be 4C [20070320] coretemp0: <CPU On-Die Thermal Sensors> on cpu0 est0: <Enhanced SpeedStep Frequency Control> on cpu0 est0: Setting 2200 MHz p4tcc0: <CPU Frequency Thermal Control> on cpu0 cpu1: <ACPI CPU> on acpi0 coretemp1: <CPU On-Die Thermal Sensors> on cpu1 est1: <Enhanced SpeedStep Frequency Control> on cpu1 est1: Setting 2200 MHz p4tcc1: <CPU Frequency Thermal Control> on cpu1 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 vgapci0: <VGA-compatible display> port 0xec00-0xec07 mem 0xfea80000-0xfeafffff,0xd0000000-0xdfffffff,0xfe900000-0xfe9fffff irq 16 at device 2.0 on pci0 pci0: <simple comms> at device 3.0 (no driver attached) em0: <Intel(R) PRO/1000 Network Connection 6.9.0> port 0xe880-0xe89f mem 0xfea40000-0xfea5ffff,0xfea7a000-0xfea7afff irq 20 at device 25.0 on pci0 em0: [FILTER] em0: Ethernet address: 00:1e:8c:75:03:0d uhci0: <UHCI (generic) USB controller> port 0xe400-0xe41f irq 16 at device 26.0 on pci0 uhci0: [GIANT-LOCKED] uhci0: [ITHREAD] usb0: <UHCI (generic) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 uhub0: 2 ports with 2 removable, self powered uhci1: <UHCI (generic) USB controller> port 0xe480-0xe49f irq 21 at device 26.1 on pci0 uhci1: [GIANT-LOCKED] uhci1: [ITHREAD] usb1: <UHCI (generic) USB controller> on uhci1 usb1: USB revision 1.0 uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1 uhub1: 2 ports with 2 removable, self powered uhci2: <UHCI (generic) USB controller> port 0xe800-0xe81f irq 18 at device 26.2 on pci0 uhci2: [GIANT-LOCKED] uhci2: [ITHREAD] usb2: <UHCI (generic) USB controller> on uhci2 usb2: USB revision 1.0 uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2 uhub2: 2 ports with 2 removable, self powered ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfea7b800-0xfea7bbff irq 18 at device 26.7 on pci0 ehci0: [GIANT-LOCKED] ehci0: [ITHREAD] usb3: EHCI version 1.0 usb3: companion controllers, 2 ports each: usb0 usb1 usb2 usb3: <EHCI (generic) USB 2.0 controller> on ehci0 usb3: USB revision 2.0 uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3 uhub3: 6 ports with 6 removable, self powered uhci3: <UHCI (generic) USB controller> port 0xdc00-0xdc1f irq 23 at device 29.0 on pci0 uhci3: [GIANT-LOCKED] uhci3: [ITHREAD] usb4: <UHCI (generic) USB controller> on uhci3 usb4: USB revision 1.0 uhub4: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4 uhub4: 2 ports with 2 removable, self powered uhci4: <UHCI (generic) USB controller> port 0xe000-0xe01f irq 19 at device 29.1 on pci0 uhci4: [GIANT-LOCKED] uhci4: [ITHREAD] usb5: <UHCI (generic) USB controller> on uhci4 usb5: USB revision 1.0 uhub5: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb5 uhub5: 2 ports with 2 removable, self powered uhci5: <UHCI (generic) USB controller> port 0xe080-0xe09f irq 18 at device 29.2 on pci0 uhci5: [GIANT-LOCKED] uhci5: [ITHREAD] usb6: <UHCI (generic) USB controller> on uhci5 usb6: USB revision 1.0 uhub6: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb6 uhub6: 2 ports with 2 removable, self powered ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfea7b400-0xfea7b7ff irq 23 at device 29.7 on pci0 ehci1: [GIANT-LOCKED] ehci1: [ITHREAD] usb7: EHCI version 1.0 usb7: companion controllers, 2 ports each: usb4 usb5 usb6 usb7: <EHCI (generic) USB 2.0 controller> on ehci1 usb7: USB revision 2.0 uhub7: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb7 uhub7: 6 ports with 6 removable, self powered pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci1: <ACPI PCI bus> on pcib1 fwohci0: <Lucent FW322/323> mem 0xfebff000-0xfebfffff irq 20 at device 2.0 on pci1 fwohci0: [FILTER] fwohci0: OHCI version 1.0 (ROM=1) fwohci0: No. of Isochronous channels is 8. fwohci0: EUI64 00:1e:8c:00:00:1a:5f:da fwohci0: Phy 1394a available S400, 2 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 fwohci0: Initiate bus reset fwohci0: BUS reset fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel AHCI controller> port 0xd800-0xd807,0xd480-0xd483,0xd400-0xd407,0xd080-0xd083,0xd000-0xd01f mem 0xfea79800-0xfea79fff irq 22 at device 31.2 on pci0 atapci0: [ITHREAD] atapci0: AHCI Version 01.20 controller with 6 ports detected ata2: <ATA channel 0> on atapci0 ata2: [ITHREAD] ata3: <ATA channel 1> on atapci0 ata3: [ITHREAD] ata4: <ATA channel 2> on atapci0 ata4: [ITHREAD] ata5: <ATA channel 3> on atapci0 ata5: [ITHREAD] ata6: <ATA channel 4> on atapci0 ata6: [ITHREAD] ata7: <ATA channel 5> on atapci0 ata7: [ITHREAD] ichsmb0: <SMBus controller> port 0x400-0x41f mem 0xfea7b000-0xfea7b0ff irq 18 at device 31.3 on pci0 ichsmb0: [GIANT-LOCKED] ichsmb0: [ITHREAD] smbus0: <System Management Bus> on ichsmb0 smb0: <SMBus generic I/O> on smbus0 pci0: <dasp> at device 31.6 (no driver attached) acpi_button0: <Power Button> on acpi0 ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 7 drq 3 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/9 bytes threshold ppbus0: <Parallel port bus> on ppc0 ppbus0: [ITHREAD] ppc0: [GIANT-LOCKED] ppc0: [ITHREAD] sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A sio0: [FILTER] atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] orm0: <ISA Option ROM> at iomem 0xcb800-0xcc7ff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 WARNING: ZFS is considered to be an experimental feature in FreeBSD. Timecounters tick every 1.000 msec firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) firewire0: bus manager 0 (me) ZFS filesystem version 6 ZFS storage pool version 6 ad4: 305245MB <SAMSUNG HD321KJ CP100-10> at ata2-master SATA300 ad6: 476940MB <WDC WD5000AAKS-00YGA0 12.01C02> at ata3-master SATA300 ad10: 476940MB <WDC WD5000AAKS-00YGA0 12.01C02> at ata5-master SATA300 ad12: 476940MB <WDC WD5000AAKS-00YGA0 12.01C02> at ata6-master SATA300 ad14: 476940MB <WDC WD5000AAKS-00YGA0 12.01C02> at ata7-master SATA300 SMP: AP CPU #1 Launched! GEOM_RAID5: storage: device created (stripesize=131072). GEOM_RAID5: storage: ad6(0): newest disk data (CALM): 0. GEOM_RAID5: storage: ad6(0): disk attached. GEOM_RAID5: storage: ad10(1): newest disk data (CALM): 1. GEOM_RAID5: storage: ad10(1): disk attached. GEOM_RAID5: storage: ad12(2): newest disk data (CALM): 2. GEOM_RAID5: storage: ad12(2): disk attached. GEOM_RAID5: storage: ad14(3): newest disk data (CALM): 3. GEOM_RAID5: storage: ad14(3): disk attached. GEOM_RAID5: storage: activated (need about 76MiB kmem (max)). Trying to mount root from ufs:/dev/ad4s1a WARNING: / was not properly dismounted WARNING: /tmp was not properly dismounted WARNING: /usr was not properly dismounted WARNING: /var was not properly dismounted /var: mount pending error: blocks 4 files 1 ============================================ dmesg ==================================== kernel config cpu HAMMER ident BLOB makeoptions DEBUG=-g # Build kernel with gdb(1) debug symbols options SCHED_ULE # ULE scheduler options PREEMPTION # Enable kernel thread preemption options INET # InterNETworking options FFS # Berkeley Fast Filesystem options SOFTUPDATES # Enable FFS soft updates support options UFS_ACL # Support for access control lists options UFS_DIRHASH # Improve performance on big directories options MD_ROOT # MD is a potential root device options NFSCLIENT # Network Filesystem Client options NFSSERVER # Network Filesystem Server options NFSLOCKD # Network Lock Manager options PROCFS # Process filesystem (requires PSEUDOFS) options PSEUDOFS # Pseudo-filesystem framework options GEOM_LABEL # Provides labelization options COMPAT_43TTY # BSD 4.3 TTY compat [KEEP THIS!] options COMPAT_IA32 # Compatible with i386 binaries options COMPAT_FREEBSD4 # Compatible with FreeBSD4 options COMPAT_FREEBSD5 # Compatible with FreeBSD5 options COMPAT_FREEBSD6 # Compatible with FreeBSD6 options SCSI_DELAY=5000 # Delay (in ms) before probing SCSI options KTRACE # ktrace(1) support options STACK # stack(9) support options SYSVSHM # SYSV-style shared memory options SYSVMSG # SYSV-style message queues options SYSVSEM # SYSV-style semaphores options _KPOSIX_PRIORITY_SCHEDULING # POSIX P1003_1B real-time extensions options KBD_INSTALL_CDEV # install a CDEV entry in /dev options ADAPTIVE_GIANT # Giant mutex is adaptive. options STOP_NMI # Stop CPUS using NMI instead of IPI options AUDIT # Security event auditing # Make an SMP-capable kernel by default options SMP # Symmetric MultiProcessor Kernel # CPU frequency control device cpufreq device coretemp device smb device smbus device ichsmb device iicbus device iicsmb device iic # Bus support. device acpi device pci # ATA and ATAPI devices device ata device atadisk # ATA disk drives options ATA_STATIC_ID # Static device numbering # atkbdc0 controls both the keyboard and the PS/2 mouse device atkbdc # AT keyboard controller device atkbd # AT keyboard device psm # PS/2 mouse device kbdmux # keyboard multiplexer device vga # VGA video card driver # syscons is the default console driver, resembling an SCO console device sc # Serial (COM) ports device sio # 8250, 16[45]50 based serial ports device uart # Generic UART driver # Parallel port device ppc device ppbus # Parallel port bus (required) device em # Intel PRO/1000 adapter Gigabit Ethernet Card # Pseudo devices. device loop # Network loopback device random # Entropy device device ether # Ethernet support device tun # Packet tunnel. device pty # Pseudo-ttys (telnet etc) device md # Memory "disks" device firmware # firmware assist module # The `bpf' device enables the Berkeley Packet Filter. # Be aware of the administrative consequences of enabling this! # Note that 'bpf' is required for DHCP. device bpf # Berkeley packet filter # USB support device uhci # UHCI PCI->USB interface device ehci # EHCI PCI->USB interface (USB 2.0) device usb # USB Bus (required) # FireWire support device firewire # FireWire bus code ==================================== kernel config -- // Black Lion AKA Lev Serebryakov <lev@FreeBSD.org>
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200805231810.m4NIA69U061540>