Date: Wed, 24 Sep 2003 22:12:08 +0300 From: Tomi Vainio - Sun Finland <Tomi.Vainio@Sun.COM> To: jtregunna@fuqn.ca Cc: freebsd-sparc64@freebsd.org Subject: Booting from ISP on U2 Message-ID: <16241.60552.668999.347682@ultrahot.finland.sun.com> In-Reply-To: <20030924183600.GA25450@fuqn.ca> References: <20030924183600.GA25450@fuqn.ca>
next in thread | previous in thread | raw e-mail | index | archive | help
jtregunna@fuqn.ca writes: > I'm trying to get FreeBSD to boot from a disk that is connected to the > onboard fas scsi controller, but through the QLogic ISP1000 SBus card > in this system. Is this even possible? I've seen other posts about this > but have not been able to find out exactly how to do it. I've tried > booting using: boot /sbus@1f,0/QLGC,isp@3,10000/sd@0,0 and also tried > with a :a appended to the end of that. I get Can't open boot device > each time I try and boot. There is an installed system on there, it > is not yet FreeBSD, but I want to make sure I can boot from the ISP > before installing. I'd like to get to installing today. > > Any help would be appreciated. > I've done this at least once using Ultra1E about year ago. I even found boot log from that. Tomppa ok boot cdrom Resetting ... Sun Ultra 1 UPA/SBus (UltraSPARC 200MHz), No Keyboard OpenBoot 3.11, 128 MB memory installed, Serial #10350439. Ethernet address 8:0:20:9d:ef:67, Host ID: 809def67. Initializing Memory \ Rebooting with command: boot cdrom Boot device: /sbus/SUNW,fas@e,8800000/sd@6,0:f File and args: >> FreeBSD/sparc64 boot block Boot path: /sbus@1f,0/SUNW,fas@e,8800000/sd@6,0:f Boot loader: /boot/loader Console: OpenFirmware console Boot path set to /sbus@1f,0/SUNW,fas@e,8800000/sd@6,0:a FreeBSD/sparc64 bootstrap loader, Revision 1.0 (scottl@numenor.btc.adaptec.com, Sun Dec 22 09:20:57 MST 2002) bootpath="/sbus@1f,0/SUNW,fas@e,8800000/sd@6,0:a" |Loading /boot/defaults/loader.conf /boot/kernel/kernel data=0x313208+0xe8c48 /syms=[0x8+0x498c0-\|+0x8+0x38d77/] -\|/ Hit [Enter] to boot immediately, or any other key for command prompt. nothing to autoload yet. -\|/jumping to kernel entry at 0xc0038000. stray vector interrupt 2033 Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.0-RC2 #0: Sun Dec 29 00:27:38 GMT 2002 root@numenor.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xc0882000. Preloaded mfs_root "/boot/mfsroot" at 0xc0882190. Timecounter "tick" frequency 199996218 Hz cpu0: Sun Microsystems UltraSparc-I Processor (200.00 MHz CPU) Model: SUNW,Ultra-1 Initializing GEOMetry subsystem md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xc047e498 nexus0: <OpenFirmware Nexus device> sbus0: clock 25.000 MHz DVMA map: 0xff800000 to 0xffffffff initialializing counter-timer Timecounter "counter-timer" frequency 1000000 Hz sbus0: <U2S UPA-SBus bridge> on nexus0 sbus0: <SUNW,CS4231>, type (unknown) (no driver attached) sbus0: <auxio>, type (unknown) (no driver attached) sbus0: <flashprom>, type (unknown) (no driver attached) sbus0: <SUNW,fdtwo>, type block (no driver attached) eeprom0: <SBus EEPROM/clock> mem 0x1200000-0x1201fff on sbus0 eeprom0: model mk48t59 eeprom0: hostid 809def67 sbus0: <zs>, type serial (no driver attached) sbus0: <zs>, type serial (no driver attached) sbus0: <sc>, type (unknown) (no driver attached) sbus0: <SUNW,pll>, type (unknown) (no driver attached) sbus0: <SUNW,fas>, type scsi (no driver attached) hme0: <Sun HME 10/100 Ethernet> mem 0x8c07000-0x8c0701f,0x8c06000-0x8c07fff,0x8c04000-0x8c05fff,0x8c02000-0x8c03fff,0x8c00000-0x8c00107 irq 2017 on sbus0 hme0: Ethernet address: 08:00:20:9d:ef:67 miibus0: <MII bus> on hme0 nsphy0: <DP83840 10/100 media interface> on miibus0 nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto sbus0: <SUNW,bpp>, type (unknown) (no driver attached) isp0 mem 0x10000-0x1044f irq 1987 on sbus0 sbus0: <SUNW,socal>, type socal (no driver attached) nexus0: <SUNW,ffb>, type display (no driver attached) Timecounters tick every 10.000 msec Waiting 15 seconds for SCSI devices to settle da0 at isp0 bus 0 target 2 lun 0 da0: <SEAGATE ST32550W SUN2.1G 0418> Fixed Direct Access SCSI-2 device da0: 20.000MB/s transfers (10.000MHz, offset 12, 16bit), Tagged Queueing Enabled da0: 2048MB (4194995 512 byte sectors: 255H 63S/T 261C) Mounting root from ufs:/dev/md0 Invalid time in real time clock. Check and reset the date immediately! /stand/sysinstall running as init on serial console These are the predefined terminal types available to sysinstall when running stand-alone. Please choose the closest match for your particular terminal. 1 ...................... Standard ANSI terminal. 2 ...................... VT100 or compatible terminal. 3 ...................... FreeBSD system console (color). 4 ...................... FreeBSD system console (monochrome). 5 ...................... xterm terminal emulator. Your choice: (1-5) 2 Waiting (max 60 seconds) for system process `bufdaemon' to stop...stopped Waiting (max 60 seconds) for system process `syncer' to stop...stopped syncing disks, buffers remaining... 8 8 done Uptime: 2m57s Program terminated
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?16241.60552.668999.347682>