Date: Sat, 14 Sep 2002 18:10:26 -0700 (PDT) From: Pete Carah <pete@ns.altadena.net> To: current@freebsd.org, mobile@freebsd.org Subject: Re: VAIO R505ES TI cardbus Message-ID: <200209150110.g8F1AQeg006450@ns.altadena.net> In-Reply-To: <20020913061314.GA735@laptop.6bone.nl> from Mark Santcroos at "Sep 13, 2002 08:13:14 am"
next in thread | previous in thread | raw e-mail | index | archive | help
> On Thu, Sep 12, 2002 at 07:24:44PM -0700, Pete Carah wrote:
> > With current as of today, I can finally get the system to
> > boot without acpi enabled, but not otherwise. However,
> > with all combinations of hw.pcic.intr_path={0,1,2},
> > hw.pcic.irq=0, and hw.pcic.init_routing={0,1} the TI
> > is not happy and I can't use the wireless.
> >
> > Since this system is acpi-only it would eventually be
> > nice to get the int routing to work with acpi (actually
> > for the Sony, it would be nice to get int routing to
> > work at all (or is loader.conf not the place for hw.pcic.*?)
> >
> > with acpi enabled it hangs after "trying sbin/init".
> > I thought jhb had committed some fixes for this; do
> > they work on any system?
>
> They did for me: Dell Latitude C640.
>
> Mark
System VAIO R505ES -
As of today (9/14) afternoon PDT, it still doesn't work; I did see some
acpi changes committed yesterday... With acpi disabled I now have irq
problems on uhci2, cbb1, and fwohci. These do appear to all be behind
a bridge(s) (fw on pci2 and the other two on pci1. However, uhci0 and 1
are also on pci1 and get irqs...)
Note: I did turn off PNP OS as hinted in the fwohci message; this appears
to make no difference at all to anything (i.e. uhci0 and 1 and fxp still
seem to work either way)...
Congrats to those who managed to get fw in at all, and the i830 fixes.
This system should be at least usable pretty soon.
Non-acpi verbose DMESG follows (I'll have to use a serial console to
get the acpi one since it still hangs at /sbin/init :-(
This is with PNP-OS off.
-------------------------------------------------------------
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #2: Sat Sep 14 17:16:24 PDT 2002
pete@port2.altadena.net:/d/obj-c/usr/src/sys/PORT2
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0456000.
Preloaded elf module "/boot/kernel/firewire.ko" at 0xc04560a8.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0456158.
Calibrating clock(s) ... TSC clock: 1193145328 Hz, i8254 clock: 1193223 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC" frequency 1193108318 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (1193.11-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 266862592 (260608K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009dfff, 643072 bytes (157 pages)
0x0047d000 - 0x0fceffff, 260517888 bytes (63603 pages)
0x0fd00000 - 0x0fe77fff, 1540096 bytes (376 pages)
avail memory = 253771776 (247824K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f6ba0
bios32: Entry = 0xfd871 (c00fd871) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xfd870+0x13a
pnpbios: Found PnP BIOS data at 0xc00f6bd0
pnpbios: Entry = f0000:880c Rev = 1.0
Other BIOS signatures found:
random: <entropy source>
null: <null device, zero device>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000f904
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=35758086)
Using $PIR table, 9 entries at 0xc00fdf30
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 2 5 A 0x69 3
embedded 2 8 A 0x68 9
embedded 0 29 A 0x60 9
embedded 0 29 B 0x63 9
embedded 0 2 A 0x60 9
embedded 0 1 A 0x60 9
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <SONY C1 > on motherboard
pcib0: <Host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base 00000000, size 0, enabled
found-> vendor=0x8086, dev=0x3575, revid=0x04
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
map[10]: type 3, range 32, base e8000000, size 27, enabled
map[14]: type 1, range 32, base e0000000, size 19, enabled
found-> vendor=0x8086, dev=0x3577, revid=0x04
bus=0, slot=2, func=0
class=03-00-00, hdrtype=0x00, mfdev=1
intpin=a, irq=9
powerspec 1 supports D0 D1 D3 current D0
map[10]: type 3, range 32, base f0000000, size 27, enabled
map[14]: type 1, range 32, base e0080000, size 19, enabled
found-> vendor=0x8086, dev=0x3577, revid=0x00
bus=0, slot=2, func=1
class=03-80-00, hdrtype=0x00, mfdev=1
powerspec 1 supports D0 D1 D3 current D0
map[20]: type 4, range 32, base 00001800, size 5, enabled
found-> vendor=0x8086, dev=0x2482, revid=0x02
bus=0, slot=29, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
intpin=a, irq=9
map[20]: type 4, range 32, base 00001820, size 5, enabled
found-> vendor=0x8086, dev=0x2484, revid=0x02
bus=0, slot=29, func=1
class=0c-03-00, hdrtype=0x00, mfdev=0
intpin=b, irq=9
map[20]: type 4, range 32, base 00001840, size 5, enabled
found-> vendor=0x8086, dev=0x2487, revid=0x02
bus=0, slot=29, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
intpin=c, irq=255
found-> vendor=0x8086, dev=0x2448, revid=0x42
bus=0, slot=30, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
found-> vendor=0x8086, dev=0x248c, revid=0x02
bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
map[10]: type 4, range 32, base 000001f0, size 3, enabled
map[14]: type 4, range 32, base 000003f4, size 2, enabled
map[18]: type 4, range 32, base 00000170, size 3, enabled
map[1c]: type 4, range 32, base 00000374, size 2, enabled
map[20]: type 4, range 32, base 00001860, size 4, enabled
map[24]: type 1, range 32, base e0100000, size 10, memory disabled
found-> vendor=0x8086, dev=0x248a, revid=0x02
bus=0, slot=31, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
intpin=a, irq=255
map[20]: type 4, range 32, base 00001880, size 5, enabled
found-> vendor=0x8086, dev=0x2483, revid=0x02
bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
intpin=b, irq=255
map[10]: type 4, range 32, base 00001c00, size 8, port disabled
map[14]: type 4, range 32, base 000018c0, size 6, enabled
found-> vendor=0x8086, dev=0x2485, revid=0x02
bus=0, slot=31, func=5
class=04-01-00, hdrtype=0x00, mfdev=0
intpin=b, irq=9
map[10]: type 4, range 32, base 00002400, size 8, port disabled
map[14]: type 4, range 32, base 00002000, size 7, enabled
found-> vendor=0x8086, dev=0x2486, revid=0x02
bus=0, slot=31, func=6
class=07-03-00, hdrtype=0x00, mfdev=0
intpin=b, irq=255
agp0: <Intel 82830 (i830M GMCH) SVGA controller> mem 0xe0000000-0xe007ffff,0xe8000000-0xefffffff irq 9 at device 2.0 on pci0
agp0: detected 892k stolen memory
agp0: aperture size is 128M
pci0: <display> at device 2.1 (no driver attached)
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1800-0x181f irq 9 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x1820-0x183f irq 9 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port 0x1840-0x185f at device 29.2 on pci0
pci_cfgintr: can't route an interrupt to 0:29 INTC
uhci2: Could not allocate irq
device_probe_and_attach: uhci2 attach returned 6
pcib1: <PCIBIOS PCI-PCI bridge> at device 30.0 on pci0
pcib1: secondary bus 2
pcib1: subordinate bus 2
pcib1: I/O decode 0x3000-0x3fff
pcib1: memory decode 0xe0200000-0xe02fffff
pcib1: prefetched decode 0xfff00000-0xfffff
pci2: <PCI bus> on pcib1
pci2: physical bus=2
map[10]: type 1, range 32, base e0205000, size 11, enabled
map[14]: type 1, range 32, base e0200000, size 14, enabled
found-> vendor=0x104c, dev=0x8023, revid=0x00
bus=2, slot=2, func=0
class=0c-00-10, hdrtype=0x00, mfdev=0
intpin=a, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
found-> vendor=0x1180, dev=0x0475, revid=0x80
bus=2, slot=5, func=0
class=06-07-00, hdrtype=0x02, mfdev=0
intpin=a, irq=3
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base e0204000, size 12, enabled
map[14]: type 4, range 32, base 00003000, size 6, enabled
found-> vendor=0x8086, dev=0x1031, revid=0x42
bus=2, slot=8, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
intpin=a, irq=9
powerspec 2 supports D0 D1 D2 D3 current D0
found-> vendor=0x104c, dev=0xac50, revid=0x01
bus=2, slot=11, func=0
class=06-07-00, hdrtype=0x02, mfdev=0
intpin=a, irq=255
powerspec 1 supports D0 D1 D2 D3 current D0
fwohci0: <1394 Open Host Controller Interface> mem 0xe0200000-0xe0203fff,0xe0205000-0xe02057ff at device 2.0 on pci2
fwohci0: Invalid irq 255
fwohci0: Please switch PNP-OS to 'No' in BIOS
device_probe_and_attach: fwohci0 attach returned 6
cbb0: <RF5C475 PCI-CardBus Bridge> irq 3 at device 5.0 on pci2
pcib1: device cbb0 requested decoded memory range 0xe0200000-0xe02fffff
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fxp0: <Intel Pro/100 Ethernet> port 0x3000-0x303f mem 0xe0204000-0xe0204fff irq 9 at device 8.0 on pci2
pcib1: device fxp0 requested decoded memory range 0xe0204000-0xe0204fff
fxp0: using memory space register mapping
fxp0: Ethernet address 08:00:46:4e:96:17
fxp0: PCI IDs: 8086 1031 104d 8100 0042
fxp0: Dynamic Standby mode is disabled
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: fxp0 attached
cbb1: <TI1410 PCI-CardBus Bridge> at device 11.0 on pci2
pcib1: device cbb1 requested decoded memory range 0xe0200000-0xe02fffff
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pci_cfgintr: can't route an interrupt to 2:11 INTA
cbb: Unable to map IRQ...
device_probe_and_attach: cbb1 attach returned 12
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 ATA100 controller> port 0x1860-0x186f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 mem 0xe0100000-0xe01003ff at device 31.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1860
ata0: mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ata0-master: ATA 01 a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1868
ata1: mask=03 ostat0=00 ostat2=00
ata1-master: ATAPI 00 00
ata1-slave: ATAPI 00 00
ata1: mask=03 stat0=00 stat1=00
ata1: devices=00
ata1: at 0x170 irq 15 on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms> at device 31.6 (no driver attached)
eisa0: <EISA bus> on motherboard
eisa0: unknown card B@H0000 (0x08080000) at slot 1
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xdc000-0xdffff,0xd8000-0xdbfff,0xc0000-0xcffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1 failed to probe at port 0x3e2 iomem 0xd4000 irq 11 on isa0
pmtimer0 on isa0
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/15 bytes threshold
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 02 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 67 5f 4f 50 02 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0 failed to probe on isa0
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
procfs registered
Timecounters tick every 10.000 msec
bpf: lo0 attached
cbb0: Unsupported card type detected
ad0: success setting UDMA5 on Intel chip
Creating DISK ad0
ar: FreeBSD check1 failed
ad0: <TOSHIBA MK4018GAS/Q1.02 C> ATA-5 disk at ata0-master
ad0: 38154MB (78140160 sectors), 77520 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
ad0: piomode=4 dmamode=2 udmamode=5 cblid=1
Mounting root from ufs:/dev/ad0s2a
ad0s1: type 0x7, start 63, end = 15663374, size 15663312 : OK
ad0s2: type 0xa5, start 15663375, end = 24049304, size 8385930 : OK
ad0s3: type 0xa5, start 24049305, end = 32435234, size 8385930 : OK
ad0s4: type 0xa5, start 32435235, end = 78140159, size 45704925 : OK
start_init: trying /sbin/init
ipfw2 initialized, divert disabled, rule-based forwarding enabled, default to deny, logging disabled
splash: image decoder found: snake_saver
Linux ELF exec handler installed
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200209150110.g8F1AQeg006450>