Date: Mon, 24 Jul 2000 10:49:35 -0400 From: "Jung, Michael" <mjung@npc.net> To: "'Mike Smith'" <msmith@FreeBSD.ORG> Cc: "'freebsd-alpha@FreeBSD.ORG'" <freebsd-alpha@FreeBSD.ORG> Subject: RE: Booting from Raid Message-ID: <921763828F4BD4118D7D00805FEDF35810C5B5@EXCHANGE1>
next in thread | raw e-mail | index | archive | help
It appears that the mlx driver is just not apart of the RC2 kernel.
Here is the data on the box - once I installed on dka0 and rebuilt
a kernel with the mlx driver it recognized the mylex card but had
errors - see below
--mikej
Michael Jung
mjung@npc.net
Digital Equipment Corporation
AlphaServer 2100 4/233
SRM Console V5.3-2 VMS Palcode V5.56-7, OSF Palcode
V1.45-12
Component Status Module ID
Slot Option Hose0,Bus0, Pci
0 DecChip 21040-AA eq0.0.0.0 08-00-2B-E5-14-5C
1 NCR 53C810 pka0.7.0.1.0 SCSI Bus ID 7
dka0.0.0.1.0 RZ29L-AS
dka600.6.0.1.0 RRD43
2 Intel 82375 Bridge to Hose
1,EISA
6 Mylex dra.0.0.6.0
dra0.0.0.6.0 5 member RAID 5
dra1.0.0.6.0 3 member RAID 5
Unrecognized boot flag '0'.
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1-20000719-RC #0: Mon Jul 24 10:32:03 EDT 2000
mikej@alpha2.npc.net:/usr/src/sys/compile/alpha2
DEC AlphaServer 2100
AlphaServer 2100 4/233, 233MHz
8192 byte page size, 2 processors.
CPU: EV45 (21064A) major=6 minor=2
OSF PAL rev: 0x4000c0002012d
real memory = 668917760 (653240K bytes)
Physical memory chunk(s):
0x00768000 - 0x27fe5fff, 663216128 bytes (80959 pages)
avail memory = 643719168 (628632K bytes)
Preloaded elf kernel "kernel.new" at 0xfffffc000074c000.
md0: Malloc disk
Creating DISK md0
found-> vendor=0x1011, dev=0x0002, revid=0x23
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=34
map[10]: type 1, range 32, base 00010100, size 7
map[14]: type 1, range 32, base 81004100, size 7
found-> vendor=0x1000, dev=0x0001, revid=0x02
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=33
map[10]: type 1, range 32, base 00010000, size 8
map[14]: type 1, range 32, base 81004000, size 8
found-> vendor=0x8086, dev=0x0482, revid=0x04
class=00-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x1069, dev=0x0001, revid=0x00
class=01-04-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=32
map[10]: type 1, range 32, base 00010180, size 7
found-> vendor=0x7246, dev=0x0000, revid=0x00
class=00-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
pci0: <PCI bus> on pcib0
de0: <Digital 21040 Ethernet> port 0x10100-0x1017f mem 0x81004100-0x8100417f
irq 34 at device 0.0 on pci0
de0: interrupting at T2 irq 34
de0: DEC 21040 [10Mb/s] pass 2.3
de0: address 08:00:2b:e5:14:5c
bpf: de0 attached
sym0: <810> port 0x10000-0x100ff mem 0x81004000-0x810040ff irq 33 at device
1.0 on pci0
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: open drain IRQ line driver
sym0: using NCR-generic firmware.
sym0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 00/00/00/00/00/00
sym0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 03/c8/00/00/08/00
sym0: Delay (GEN=11): 263 msec, 33795 KHz
sym0: Delay (GEN=11): 262 msec, 33924 KHz
sym0: Delay (GEN=11): 262 msec, 33924 KHz
sym0: interrupting at T2 irq 33
isab0: <Intel 82375EB PCI-EISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
mlx0: <Mylex version 2 RAID interface> port 0x10180-0x101ff irq 32 at device
6.0 on pci0
mlx0: couldn't allocate mailbox window
device_probe_and_attach: mlx0 attach returned 6
pci0: <unknown card> (vendor=0x7246, dev=0x0000) at 15.0
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: interrupting at T2 irq 6
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0003
atkbd: keyboard ID 0x83ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: interrupting at T2 irq 1
psm0: current command byte:0043
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 90 03 3c
psm: status 90 03 3c
psm: status 90 03 3c
psm: data 08 00 00
psm: status 00 00 0a
psm: status 00 02 64
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: interrupting at T2 irq 12
psm0: model Generic PS/2 mouse, device ID 0-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xb8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0
Calibrating clock(s) ... PCC clock: 233343215 Hz (firmware 233100233 Hz)
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0 at port 0x3f8-0x3ff irq 4 on isa0
sio0: type 16550A
sio0: interrupting at T2 irq 4
sio1: reserved for low-level i/o
ppc0: using normal I/O port range
ppc0: SPP
ppc0: <Parallel port> at port 0x3bc-0x3bf irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Polled port
plip0: cannot reserve interrupt, failed.
ppc0: interrupting at T2 irq 7
isa_probe_children: probing PnP devices
Timecounter "alpha" frequency 233343215 Hz
bpf: sl0 attached
bpf: ppp0 attached
bpf: lo0 attached
bpf: gif0 attached
bpf: gif1 attached
bpf: gif2 attached
bpf: gif3 attached
bpf: faith0 attached
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
de0: enabling 10baseT port
(probe6:sym0:0:6:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe6:sym0:0:6:0): ILLEGAL REQUEST asc:24,0
(probe6:sym0:0:6:0): Invalid field in CDB sks:c8,1
Creating DISK da0
Creating DISK cd0
pass0 at sym0 bus 0 target 0 lun 0
pass0: <DEC RZ29L-AS (C) DEC 0814> Fixed Direct Access SCSI-2 device
pass0: Serial Number JDM7494509WKM3
pass0: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
pass1 at sym0 bus 0 target 6 lun 0
pass1: <DEC RRD43 (C) DEC 1084> Removable CD-ROM SCSI-2 device
pass1: 4.166MB/s transfers (4.166MHz, offset 8)
da0 at sym0 bus 0 target 0 lun 0
da0: <DEC RZ29L-AS (C) DEC 0814> Fixed Direct Access SCSI-2 device
da0: Serial Number JDM7494509WKM3
da0: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
da0: 4091MB (8380080 512 byte sectors: 255H 63S/T 521C)
cd0 at sym0 bus 0 target 6 lun 0
cd0: <DEC RRD43 (C) DEC 1084> Removable CD-ROM SCSI-2 device
cd0: 4.166MB/s transfers (4.166MHz, offset 8)
cd0: cd present [316732 x 512 byte records]
Mounting root from ufs:/dev/da0a
da0: invalid primary partition table: no magic
start_init: trying /sbin/init
-----Original Message-----
From: owner-freebsd-alpha@FreeBSD.ORG
[mailto:owner-freebsd-alpha@FreeBSD.ORG]On Behalf Of Mike Smith
Sent: Friday, July 21, 2000 8:20 PM
To: Michael Jung
Cc: freebsd-alpha@FreeBSD.ORG
Subject: Re: Booting from Raid
>
> Ok I admit I've probably not looked hard enough
> but it seems that I read recently that you should
> be able to boot from DAC960 PCI raid partitions
> under FreeBSD-Alpha...
>
> Shortly before I left work today we started to
> load the rc2 iso on a 2100 and it did not
> recognize the raid partition..
Can you provide some more details? The output of "show conf" relevant to
this card would be a start, as well as the FreeBSD kernel probe messages.
You may also have to load the 'mlx' module (this requires booting from
floppies, irritatingly) since I get the sneaking suspicion it's not in
the GENERIC kernel for Alpha systems. Space in that kernel is *really*
tight.
--
... every activity meets with opposition, everyone who acts has his
rivals and unfortunately opponents also. But not because people want
to be opponents, rather because the tasks and relationships force
people to take different points of view. [Dr. Fritz Todt]
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-alpha" in the body of the message
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-alpha" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?921763828F4BD4118D7D00805FEDF35810C5B5>