Date: Tue, 25 Sep 2001 11:08:27 -0500 (CDT) From: "M. L. Dodson" <bdodson@scms.utmb.EDU> To: freebsd-alpha@FreeBSD.ORG Subject: problem with lynx and recent -current Message-ID: <200109251608.f8PG8R540820@histidine.utmb.edu> In-Reply-To: <200109211837.f8LIbwd26854@histidine.utmb.edu> References: <200109211837.f8LIbwd26854@histidine.utmb.edu>
next in thread | previous in thread | raw e-mail | index | archive | help
Well, this did not go through the first time, so let's try again. M. L. Dodson writes: > > Machine is a 4CPU AS2100A 5/250, 1GB mem. > > Successfully installed a 4.4RC minimal system, cvsupped to recent > current (approx 11:10 AM CDT [US Central time], Sept. 20, from > cvsup6), did make buildworld (which completed with no errors), > did make buildkernel using a config file created by just removing > extraneous stuff from GENERIC. The config file was NOT for an > SMP kernel. Copied GENERIC.hints to /boot/device.hints and did > make installkernel. Rebooted successfully into single user mode > to run installworld (which was successful) and mergemaster (which > was uneventful). When I rebooted single user I got (copied by > hand): > Here is a followup on my report in the Subject. The whole script can be retrieved from http://www.scms.utmb.edu/bdodson/lynx.log Notes: 1. This was NOT a SMP-enabled kernel 2. This machine successfully booted and ran a 4.4RC, so hardware problems seem unlikely [initial SRM stuff elided, boot output follows:] VMS PALcode V1.19-2, OSF PALcode V1.21-1 starting console on CPU 0 Testing Memory bank 0 Testing Memory bank 1 Testing Memory bank 2 Testing Memory bank 3 Configuring Memory Modules probing hose 0, PCI probing PCI-to-EISA bridge, bus 1 probing PCI-to-PCI bridge, bus 2 bus 2, slot 1 -- pka -- NCR 53C810 bus 2, slot 9 -- ewa -- DECchip 21040-AA bus 0, slot 6 -- vga -- S3 Trio64/Trio32 ** keyboard error ** starting console on CPU 1 starting console on CPU 2 starting console on CPU 3 os_type: UNIX - console CIPCA driver not started Memory Testing and Configuration Status Module Size Base Addr Intlv Mode Intlv Unit Status ------ ----- --------- ---------- ---------- ------ 2 512MB 00000000 2-Way 0 Passed 3 512MB 00000000 2-Way 1 Passed Total Bad Pages 0 Testing the System Testing the Disks (read only) Testing the Network AlphaServer 2100A Console V4.7-157, built on Nov 20 1996 at 14:44:52 P00>>>boot dka0 (boot dka0.0.0.2001.0 -flags 0) block 0 of dka0.0.0.2001.0 is a valid boot block reading 15 blocks from dka0.0.0.2001.0 bootstrap code read in base = 200000, image_start = 0, image_bytes = 1e00 initializing HWRPB at 2000 initializing page table at 3fff0000 initializing machine state setting affinity to the primary CPU jumping to bootstrap code [propeller twirling elided] Loading /boot/loader [more propeller twirling elided] Console: SRM firmware console VMS PAL rev: 0x4000200010113 OSF PAL rev: 0x4000100020115 Switch to OSF PAL code succeeded. FreeBSD/alpha SRM disk boot, Revision 1.1 (bdodson@lynx.utmb.edu, Thu Sep 20 15:17:55 CDT 2001) Memory: 1048576 k [more propeller twirling elided] Loading /boot/defaults/loader.conf [more propeller twirling elided] Hit [Enter] to boot immediately, or any other key for command prompt. Booting [/boot/kernel/kernel] in 9 seconds... Booting [/boot/kernel/kernel] in 8 seconds... Booting [/boot/kernel/kernel]... [more propeller twirling elided] Entering /boot/kernel/kernel at 0xfffffc000032cf20... sio1: gdb debugging port Unrecognized boot flag '0'. Copyright (c) 1992-2001 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.0-CURRENT #0: Thu Sep 20 21:30:24 CDT 2001 bdodson@lynx.utmb.edu:/usr/obj/usr/src/sys/LYNX DEC AlphaServer 2100A AlphaServer 2100A 5/250, 250MHz 8192 byte page size, 4 processors. CPU: EV5 (21164) major=5 minor=5 OSF PAL rev: 0x4000100020115 real memory = 1071570944 (1046456K bytes) avail memory = 1038508032 (1014168K bytes) Preloaded elf kernel "/boot/kernel/kernel" at 0xfffffc00006b0000. t20: using interrupt type 1 on pci bus 0 t20: <T2 Core Logic chipset> halted CPU 0 halt code = 6 double error halt PC = 18fe8 starting console on CPU 0 starting console on CPU 0 breakpoint at PC 11d8f0 desired, XDELTA not loaded interrupt through vector 670 on CPU 0 EV5 detected B-Cache parity or ECC error CPU detected C-bus error *** unexpected machine check through vector 00000067 [register dump elided] -- M. L. Dodson bdodson@scms.utmb.edu 409-772-2178 FAX: 409-772-1790 To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-alpha" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200109251608.f8PG8R540820>