Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 11 Apr 2005 14:53:53 -0500
From:      Eric Schuele <e.schuele@computer.org>
To:        usb@freebsd.org
Subject:   Trouble with TEAC usb floppy (FD-05PUB)
Message-ID:  <425AD5D1.8080301@computer.org>

next in thread | raw e-mail | index | archive | help
Hello,

I am having difficulty with my TEAC usb floppy drive (FD-05PUB).  I'm 
not really sure what's wrong.  Plugging it in.. it appears to get 
detected.  But it is unusable.  I always get a 'device busy' after 
mounting it.

Attached is a dmesg obtained after booting with the drive plugged in. 
Also of note... the "* was not properly dismounted" is due to the fact 
that FreeBSD gave up on the buffers when shutting down... because of the 
floppy.  If I'm luck it gives up.  Sometimes I get a kernel trap.

This has been an ongoing problem since 5.2 (Presently running 5.4-STABLE 
as of a few days ago).

Is anyone else seeing this problem?  Should I file a PR?  Its been going 
on for quite sometime.

Any help is appreciated.  If anymore information is needed please let me 
know.
-- 
Regards,
Eric


FreeBSD fangorn.nxdomain.org 5.4-STABLE FreeBSD 5.4-STABLE #10: Wed Apr 
  6 00:21:02 CDT 2005 
root@fangorn.nxdomain.org:/usr/obj/usr/src/sys/CUSTOM  i386

Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.4-STABLE #10: Wed Apr  6 00:21:02 CDT 2005
     root@fangorn.nxdomain.org:/usr/obj/usr/src/sys/CUSTOM
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) 4 CPU 2.66GHz (2657.83-MHz 686-class CPU)
   Origin = "GenuineIntel"  Id = 0xf29  Stepping = 9
 
Features=0xbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
real memory  = 536645632 (511 MB)
avail memory = 515473408 (491 MB)
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL CPi R  > on motherboard
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_acad0: <AC Adapter> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI link \\_SB_.PCI0.LNKB has invalid initial irq 11, ignoring
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82845G host to AGP bridge> mem 0xe0000000-0xe7ffffff at 
device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
drm0: <ATI Radeon LW Mobility 7500 M7> port 0xc000-0xc0ff mem 
0xfcff0000-0xfcffffff,0xe8000000-0xefffffff irq 11 at device 0.0 on pci1
info: [drm] AGP at 0xe0000000 128MB
info: [drm] Initialized radeon 1.11.0 20020828 on minor 0
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xbf80-0xbf9f 
irq 11 at device 29.0 on pci0
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xbf40-0xbf5f 
irq 11 at device 29.1 on pci0
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xbf20-0xbf3f 
irq 11 at device 29.2 on pci0
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
bfe0: <Broadcom BCM4401 Fast Ethernet> mem 0xfaffe000-0xfaffffff irq 5 
at device 1.0 on pci2
miibus0: <MII bus> on bfe0
bmtphy0: <BCM4401 10/100baseTX PHY> on miibus0
bmtphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bfe0: Ethernet address: 00:0d:56:b4:f1:50
ath0: <Atheros 5212> mem 0xfafe0000-0xfafeffff irq 11 at device 2.0 on pci2
ath0: mac 5.9 phy 4.3 5ghz radio 3.6
ath0: Ethernet address: 00:0e:9b:53:31:9d
ath0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 
24Mbps 36Mbps 48Mbps 54Mbps
cbb0: <TI4510 PCI-CardBus Bridge> at device 4.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fwohci0: <1394 Open Host Controller Interface> mem 
0xfaff8000-0xfaffbfff,0xfaffd800-0xfaffdfff irq 11 at device 4.1 on pci2
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 39:4f:c0:00:03:57:18:81
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 3a:4f:c0:57:18:81
fwe0: Ethernet address: 3a:4f:c0:57:18:81
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port 
0xbfa0-0xbfaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
pcm0: <Intel ICH4 (82801DB)> port 0xbc40-0xbc7f,0xb800-0xb8ff mem 
0xf4fff400-0xf4fff4ff,0xf4fff800-0xf4fff9ff irq 5 at device 31.5 on pci0
pcm0: <SigmaTel STAC9750/51 AC97 Codec>
pci0: <simple comms, generic modem> at device 31.6 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x66,0x62,0x64,0x60 irq 1 on 
acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> flags 0x1000 irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
orm0: <ISA Option ROMs> at iomem 
0xcf800-0xcffff,0xcf000-0xcf7ff,0xc0000-0xcefff on isa0
pmtimer0 on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
umass0: TEAC TEAC FD-05PUB, rev 2.00/0.00, addr 2
Timecounter "TSC" frequency 2657825740 Hz quality 800
Timecounters tick every 10.000 msec
acd0: CDRW <QSI CD-RW/DVD-ROM SBW-242/UD30> at ata0-master PIO4
ad2: 38154MB <IC25N040ATMR04-0/MO2OAD0A> [77520/16/63] at ata1-master 
UDMA100
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <TEAC FD-05PUB 3000> Removable Direct Access SCSI-0 device
da0: 1.000MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
(da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI Status: Check Condition
(da0:umass-sim0:0:0:0): NOT READY asc:3a,0
(da0:umass-sim0:0:0:0): Medium not present
(da0:umass-sim0:0:0:0): Unretryable error
Opened disk da0 -> 6
(da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI Status: Check Condition
(da0:umass-sim0:0:0:0): NOT READY asc:3a,0
(da0:umass-sim0:0:0:0): Medium not present
(da0:umass-sim0:0:0:0): Unretryable error
Opened disk da0 -> 6
(da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI Status: Check Condition
(da0:umass-sim0:0:0:0): NOT READY asc:3a,0
(da0:umass-sim0:0:0:0): Medium not present
(da0:umass-sim0:0:0:0): Unretryable error
Opened disk da0 -> 6
Mounting root from ufs:/dev/ad2s1a
WARNING: / was not properly dismounted
WARNING: /tmp was not properly dismounted
WARNING: /usr was not properly dismounted
WARNING: /usr/home was not properly dismounted
WARNING: /var was not properly dismounted
(da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI Status: Check Condition
(da0:umass-sim0:0:0:0): UNIT ATTENTION asc:28,0
(da0:umass-sim0:0:0:0): Not ready to ready change, medium may have changed
(da0:umass-sim0:0:0:0): Retrying Command (per Sense Data)
fsync: giving up on dirty: 0xc23e7210: tag devfs, type VCHR, usecount 2, 
writecount 0, refcount 3, lock type devfs: EXCL (count 1) by thread 
0xc2196480 (pid 708)
	dev da0



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?425AD5D1.8080301>