Date: Sun, 22 Mar 1998 22:36:28 -0500 (EST) From: Obi Wan Oblivion <vdk@chaosphere.com> To: questions@FreeBSD.ORG Subject: -stable: SB Pro + PnP / IRQs Message-ID: <Pine.BSF.3.96.980322213122.1449A-100000@logrus.chaosphere.com>
next in thread | raw e-mail | index | archive | help
Hi all,
I have a PnP ISA sound card running (by default) in SoundBlaster Pro mode
on IRQ 5, DMA 1, and port 0x220. I am running 2.2-STABLE, built March
15th. I have added the following lines to my kernel config:
controller pnp0
controller snd0
device sb0 at isa? port 0x220 irq 5 drq 1 vector sbintr
options SBC_IRQ=5
rebuilt the kernel, rebooted, and ran:
# cd /dev
# ./MAKEDEV snd0
Rebooted again (just because I could) and everything seems to be detected
appropriately. The kernel pops up with:
Probing for PnP devices:
CSN 1 Vendor ID: OPT0924 [0x2409143e] Serial 0x08000000
and then with:
sb0 at 0x220 irq 5 drq 1 on isa
sb0: <SoundBlaster 2.1>
I have an AVI, complete with audio, that I have been feeding to XAnim
via:
% xanim +Ae themovie.avi
But always I am unable to hear any sound. I am unconvinced that this is
an accurate test and would like to know if there is something more
appropriate.
I am also wondering if anyone has any thoughts about other things I can
try to get this sound card running. I have tried eliminating the "option
SBC_IRQ=5" line. I have also tried adding "conflicts" to the sb0 line
above, more as a desparation move that anything else. With each of these
changes, the kernel still reports the same lines indicated above at
startup, however, with "conflicts" added to the line, and the SBC_IRQ line
included, I am now getting this error message:
Mar 20 02:26:51 logrus /kernel: Sound: DMA timed out - IRQ/DRQ config
error?
At the end of this email message, I have included the output of pnpinfo in
the hope that this information may prove useful to anyone who wishes to
help out with this.
Also, on another note, I originally had my modem set up on irq 5, but when
I installed my sound card, the modem failed to be detected. I ended up
swapping the modem over to irq 3 (stolen from a disabled sio1) and it
works fine. Now, however, X periodically hangs and then two or
three seconds later it merrily marches on, all the while spewing something
about "Cirrus: BitBLT eating itself" or words to that effect. This is
especially evident when doing work in an xterm. What might I do to
correct this? Is this as simple as throwing an "Option 'no_bitblt'" into
/etc/XF86Config? Is there a way to correct this without disabling
features? Am I correct in assuming that this is an irq conflict? Is
there a utility that will let me see a list of all of the irqs in use on
my system so that I can avoid conflicts like this in the future?
Any help on either of these fronts would be appreciated. Pointers to
reference material that I can read and learn from would be appreciated the
most.
Thanks!
-Jeff
Output of pnpinfo:
Checking for Plug-n-Play devices...
Trying Read_Port at 203...
Card assigned CSN #1
Board Vendor ID OPT0924, Serial Number 0x08000000
PnP Version 1.0, Vendor Version 0
Device Description: OPTi Audio 16
Logical Device ID: OPT0000 0x0000143e #0
Vendor register funcs 00
Device Description: Pro Audio 16
I/O Range 0x220 .. 0x240, alignment 0x20, len 0x10
[not 16-bit addr]
I/O Range 0x130 .. 0x3f0, alignment 0x4, len 0x8
[not 16-bit addr]
TAG Start DF
I/O Range 0x380 .. 0x380, alignment 0x10, len 0xc
[not 16-bit addr]
IRQ: 5 7 10 - only one type (true/edge)
DMA: channel(s) 0 1 3
8-bit, not a bus master, , , Compatibility mode
TAG Start DF
I/O Range 0x380 .. 0x3f0, alignment 0x10, len 0xc
[not 16-bit addr]
IRQ: 5 7 9 10 11 - only one type (true/edge)
DMA: channel(s) 0 1 3
8-bit, not a bus master, , , Compatibility mode
DMA: channel(s) 0 1 3
8-bit, not a bus master, , , Compatibility mode
TAG End DF
Logical Device ID: OPT0001 0x0100143e #1
Vendor register funcs 00
Compatible Device ID: PNPb02f (2fb0d041)
Device Description: Game Port
TAG Start DF
FIXED I/O base address 0x201 length 0x1
TAG Start DF
I/O Range 0x100 .. 0x3f0, alignment 0x10, len 0x2
[not 16-bit addr]
TAG End DF
Logical Device ID: OPT0002 0x0200143e #2
Vendor register funcs 00
Device Description: MPU401
IRQ: 5 7 9 10 - only one type (true/edge)
I/O Range 0x300 .. 0x330, alignment 0x10, len 0x2
[not 16-bit addr]
Logical Device ID: OPT0003 0x0300143e #3
Vendor register funcs 00
Compatible Device ID: PNP0600 (0006d041)
Device Description: CD
IRQ: 15 - only one type (true/edge)
TAG Start DF
I/O Range 0x376 .. 0x376, alignment 0x10, len 0x2
[not 16-bit addr]
I/O Range 0x170 .. 0x170, alignment 0x10, len 0x8
[not 16-bit addr]
TAG Start DF
I/O Range 0x376 .. 0x3f6, alignment 0x10, len 0x2
[not 16-bit addr]
I/O Range 0x170 .. 0x3f0, alignment 0x10, len 0x8
[not 16-bit addr]
TAG End DF
Logical Device ID: OPT0004 0x0400143e #4
Vendor register funcs 00
Compatible Device ID: PNP0500 (0005d041)
Device Description: Modem
IRQ: 3 4 5 7 9 10 11 - only one type (true/edge)
TAG Start DF
I/O Range 0x2e8 .. 0x2f8, alignment 0x10, len 0x8
[not 16-bit addr]
TAG Start DF
I/O Range 0x3e8 .. 0x3f8, alignment 0x10, len 0x8
[not 16-bit addr]
TAG Start DF
I/O Range 0x100 .. 0x3f0, alignment 0x10, len 0x8
[not 16-bit addr]
TAG End DF
Logical Device ID: OPT0005 0x0500143e #5
Vendor register funcs 00
Device Description: OPT924
I/O Range 0x30d .. 0x3ed, alignment 0x20, len 0x9
[not 16-bit addr]
TAG Start DF
TAG Start DF
IRQ: 5 10 11 - only one type (true/edge)
TAG End DF
End Tag
Successfully got 57 resources, 6 logical fdevs
-- card select # 0x0001
Logical device #0
IO: 0x0220 0x0130 0x0380 0x0000 0x0000 0x0000 0x0000 0x0000
IRQ 5 0
DMA 3 4
IO range check 0x00 activate 0x01
Logical device #1
IO: 0x0201 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
IRQ 0 0
DMA 4 4
IO range check 0x00 activate 0x01
Logical device #2
IO: 0x0300 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
IRQ 9 0
DMA 4 4
IO range check 0x00 activate 0x01
Logical device #3
IO: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
IRQ 0 0
DMA 4 4
IO range check 0x00 activate 0x00
Logical device #4
IO: 0x02e8 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
IRQ 10 0
DMA 4 4
IO range check 0x00 activate 0x01
Logical device #5
IO: 0x030d 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
IRQ 0 0
DMA 4 4
IO range check 0x00 activate 0x01
Transformers - They're more than meets the eye!
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.3.96.980322213122.1449A-100000>