Date: Sun, 30 May 2004 09:08:21 +0200 From: Jorn Argelo <jorn@wcborstel.nl> To: stefan@swebase.com Cc: freebsd-questions@freebsd.org Subject: Re: huge xfree86 problems with an acer on freebsd 5.2.1 Message-ID: <40B98865.1060002@wcborstel.nl> In-Reply-To: <00d101c445eb$f173dd70$082450d5@swebasestefan> References: <00d101c445eb$f173dd70$082450d5@swebasestefan>
next in thread | previous in thread | raw e-mail | index | archive | help
stefan@swebase.com wrote: >Hi, i already posted this on x11 but hey i really need help so please don't hold it against me... > >I have an acer aspire 1350LC with a via chipset for the graphics. I got x working once on 4.9, same laptop when i had been messing around with 4.4.0 and ports so after a while it was a really broken install but suddenly it started working using the auto configure thing, first thing i tried to do was to write my own conf file which failed over and over again. I can't use the auto configure thing since it produced a very low resolution, even if i could figure out how to use auto configure with xfree and increase the res i doubt i'd be able to reproduce last time on 5.2.1 now because it was all a large mess of ports and bloody xfree86 guts all over the place. > >Anyways the situation now is that i get no errors to stdout. Checking the logfile i see that everything is going just fine until it reads the hsync value, this is what it looks like: > >(--) via(0): No DDC signal >(II) via(0): Monitor0: Using hsync value of 31.50 kHz >(II) via(0): Monitor0: Using vrefresh range of 50.00-90.00 Hz >(II) via(0): Clock range: 20.00 to 230.00 MHz >(II) via(0): Not using default mode "640x350" (hsync out of range) >(II) via(0): Not using default mode "320x175" (bad mode clock/interlace/doublescan) >(II) via(0): Not using default mode "640x400" (hsync out of range) >(II) via(0): Not using default mode "320x200" (bad mode clock/interlace/doublescan) >(II) via(0): Not using default mode "720x400" (hsync out of range) >(II) via(0): Not using default mode "360x200" (bad mode clock/interlace/doublescan) >(II) via(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) >(II) via(0): Not using default mode "640x480" (hsync out of range) >(II) via(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) >(II) via(0): Not using default mode "640x480" (hsync out of range) >(II) via(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) >(II) via(0): Not using default mode "640x480" (hsync out of range) >(II) via(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) >[...] >(II) via(0): Not using default mode "1600x1024" (hsync out of range) >(II) via(0): Not using default mode "800x512" (bad mode clock/interlace/doublescan) >(II) via(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan) >(II) via(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan) >(II) via(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) >(II) via(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) >(II) via(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) >(II) via(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) >(II) via(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) >(II) via(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) >(II) via(0): Not using mode "1024x768" (no mode of this name) >(--) via(0): Virtual size is 640x480 (pitch 640) >(**) via(0): *Default mode "640x480": 25.2 MHz (scaled from -1206751.2 MHz), 31.5 kHz, 60.0 Hz >(II) via(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492 525 -hsync -vsync > >After this it goes on with loading a few modules, showing me some resource ranges after preInit, mapping frambuffer and exits after a few of these messages. > >(II) via(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000 >(==) via(0): Write-combining range (0xa0000,0x10000) was already clear > > > > > > >Med vänliga hälsningar > >Stefan Midjich, Swebase AB >Tel: 042-20 15 00 >Fax: 042-20 15 03 >E-post: stefan@swebase.com >Webb: http://swebase.com >_______________________________________________ >freebsd-questions@freebsd.org mailing list >http://lists.freebsd.org/mailman/listinfo/freebsd-questions >To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org" > >. > > > Why don't you just run the auto configurator and change the resolution yourself? Then you won't have the problem that your hsync is out of range, since it has been auto probed by XFree86 itself. Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 16 SubSection "Display" Depth 16 Modes "1280x1074" EndSection Cheers, Jorn Jorn
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?40B98865.1060002>