Date: Thu, 18 Jan 2001 17:06:58 -0500 From: Mike Tancsa <mike@sentex.net> To: freebsd-atm@freebsd.org Subject: ATM problems with HARP Message-ID: <5.0.1.4.0.20010118170127.02188060@marble.sentex.ca>
next in thread | raw e-mail | index | archive | help
I have been playing with the HARP stack and run into a small problem. When
running netperf, I seem to loose the PVC on my hea cards.
hespler2# uname -a
FreeBSD hespler2.sentex.ca 4.2-STABLE FreeBSD 4.2-STABLE #0: Thu Jan 18
07:45:03 EST
2001 mdtancsa@hespler2.sentex.ca:/usr/src/sys/compile/hesp.harp i386
hespler2#
./snapshot_script 192.168.1.2 > /tmp/snap.out
Netperf snapshot script started at Thu Jan 18 16:32:12 EST 2001
Starting 56x4 TCP_STREAM tests at Thu Jan 18 16:32:45 EST 2001
Starting 32x4 TCP_STREAM tests at Thu Jan 18 16:35:45 EST 2001
Starting 1,1 TCP_RR tests at Thu Jan 18 16:38:45 EST 2001
Starting 1,1 UDP_RR tests at Thu Jan 18 16:41:51 EST 2001
Starting 512,4 UDP_RR tests at Thu Jan 18 16:44:57 EST 2001
Starting 32x4 UDP_STREAM tests at Thu Jan 18 16:48:03 EST 2001
Starting 32x1 UDP_STREAM tests at Thu Jan 18 16:50:03 EST 2001
establish_control: control socket connect failed: Operation timed out
Are you sure there is a netserver running on 192.168.1.2 at port 12865?
Tests completed at Thu Jan 18 16:51:18 EST 2001
hespler2# atm show stats vcc
Input Input Input Output Output Output
Interface VPI VCI PDUs Bytes Errs PDUs Bytes Errs
hea0 0 130 3308599 144044200 0 3692025 -1804270564 0
hespler2# atm show vcc
Interface VPI VCI AAL Type Dir State Encaps Owner
hea0 0 130 AAL5 PVC InOut ACTIVE LLC/SNAP IP
hespler2# atm show ipvcc
Net Intf VPI VCI State Flags IP Address
atm0 0 130 ACTIVE PLM ruby2atm (192.168.1.2)
hespler2# atm show config
Intf Vendor Model Media Bus Serial No
hea0 ENI ENI-155p OC-3c PCI 794554
MAC address = 00:20:ea:0c:1f:ba
Hardware version = 0/4/0
Firmware version =
hespler2#
hespler2# ifconfig atm0
atm0: flags=43<UP,BROADCAST,RUNNING> mtu 9180
inet 192.168.1.1 netmask 0xfffffffc broadcast 192.168.1.3
ether 00:20:ea:0c:1f:ba
I try and delete the PVC and recreate it, but no dice. It seems only a
reboot takes care of the issue.
The config is pretty simple,
atm_enable="YES" # Configure ATM interfaces (or NO).
atm_netif_hea0="atm 1" # Network interfaces for physical interface.
atm_sigmgr_hea0="sigpvc" # Signalling manager for physical interface.
atm_pvcs="test" # Set to PVC list (or leave empty).
atm_pvc_test="hea0 0 130 aal5 snap ip atm0 192.168.1.2" #
Any thoughts on what it might be ?
---Mike
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-atm" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?5.0.1.4.0.20010118170127.02188060>