Date: Mon, 30 Aug 2004 20:18:11 +0200 From: "Lukas Razik" <lukas@razik.de> To: freebsd-hardware@freebsd.org Subject: [5.3-BETA2] acd0: FAILURE - READ_BIG HARDWARE ERROR Message-ID: <163331489@web.de>
next in thread | raw e-mail | index | archive | help
Hi!!!
I've a little problem with the 5.3-BETA2 because If I try to mount the acd0 device it doesn't work.
I always get this:
acd0: FAILURE - READ_BIG HARDWARE ERROR asc=0x08 ascq=0x03 error=0
No problems with acd1.
Another error message I get is:
Interrupt storm detected on "irq11: acpi0"; throttling interrupt source
I had no other errors/panics during installation and the rest of the system works fine.
There were no problems with earlier 5.X.X and my
acd0: DVDROM <Pioneer DVD-ROM ATAPIModel DVD-106S 0122/E1.22> at ata0-master UDMA66
Regards,
Lukas
Here the whole dmesg:
===================
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.3-BETA2 #1: Sat Aug 28 21:29:15 UTC 2004
root@mack.dcsl.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
WARNING: WITNESS option enabled, expect reduced performance.
ACPI APIC Table: <VIA692 AWRDACPI>
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Pentium III (801.82-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x68a Stepping = 10
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 1610547200 (1535 MB)
avail memory = 1568518144 (1495 MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0 <Version 1.1> irqs 0-23 on motherboard
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <VIA692 AWRDACPI> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU (3 Cx states)> on acpi0
cpu1: <ACPI CPU (3 Cx states)> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0x5000-0x500f,0x4080-0x40ff,0x4000-0x407f,0xcf8-0xcff on acpi0
pcib0: could not get PCI interrupt routing table for \\_SB_.PCI0 - AE_BAD_DATA
pci0: <ACPI PCI bus> on pcib0
pcib0: no PRT entry for 0.7.INTD
agp0: <VIA 82C691 (Apollo Pro) host to PCI bridge> mem 0xe0000000-0xe3ffffff at device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pcib0: no PRT entry for 0.1.INTA
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C596B UDMA66 controller> port 0xc000-0xc00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xc400-0xc41f irq 9 at device 7.2 on pci0
uhci0: [GIANT-LOCKED]
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
fxp0: <Intel 82557 Pro/100 Ethernet> port 0xc800-0xc81f mem 0xe7000000-0xe70fffff,0xe7103000-0xe7103fff irq 17 at device 9.0 on pci0
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:a0:c9:c5:8a:24
fxp0: [GIANT-LOCKED]
uhci1: <VIA 83C572 USB controller> port 0xcc00-0xcc1f irq 18 at device 10.0 on pci0
uhci1: [GIANT-LOCKED]
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ugen0: SiW SiW, rev 1.10/15.00, addr 2
uhci2: <VIA 83C572 USB controller> port 0xd000-0xd01f irq 19 at device 10.1 on pci0
uhci2: [GIANT-LOCKED]
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uscanner0: EPSON EPSON Scanner, rev 2.00/1.00, addr 2
pci0: <serial bus, USB> at device 10.2 (no driver attached)
atapci1: <HighPoint HPT370 UDMA100 controller> port 0xe400-0xe4ff,0xe000-0xe003,0xdc00-0xdc07,0xd800-0xd803,0xd400-0xd407 irq 16 at device 11.0 on pci0
ata2: channel #0 on atapci1
ata3: channel #1 on atapci1
pcib2: <PCI-PCI bridge> at device 12.0 on pci0
pci2: <PCI bus> on pcib2
mlx0: <Mylex version 4 RAID interface> mem 0xe7100000-0xe7101fff irq 18 at device 12.1 on pci0
mlx0: [GIANT-LOCKED]
mlx0: DAC960PG, 3 channels, firmware 4.06-0-08, 8MB RAM
mlxd0: <Mylex System Drive> on mlx0
mlxd0: 26280MB (53821440 sectors) RAID 5 (online)
mlxd1: <Mylex System Drive> on mlx0
mlxd1: 8678MB (17772544 sectors) RAID 1 (online)
pcm0: <Creative CT5880-C> port 0xe800-0xe83f irq 19 at device 13.0 on pci0
pcm0: <TriTech TR28602 AC97 Codec>
pcm0: [GIANT-LOCKED]
fdc0: <floppy drive controller> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3
orm0: <ISA Option ROMs> at iomem 0xd4000-0xd6fff,0xd0000-0xd3fff,0xc0000-0xcffff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
ATAPI_RESET time = 40us
acd0: DVDROM <Pioneer DVD-ROM ATAPIModel DVD-106S 0122/E1.22> at ata0-master UDMA66
ATAPI_RESET time = 140us
acd1: CDRW <CR-48X5TE/1.8A> at ata1-slave PIO4
ad4: 28629MB <ST330620A/3.05> [58168/16/63] at ata2-master UDMA100
ad6: 28629MB <ST330620A/3.05> [58168/16/63] at ata3-master UDMA100
ar0: 57259MB <ATA RAID0 array> [7299/255/63] status: READY subdisks:
disk0 READY on ad4 at ata2-master
disk1 READY on ad6 at ata3-master
SMP: AP CPU #1 Launched!
Mounting root from ufs:/dev/mlxd0s1a
Interrupt storm detected on "irq11: acpi0"; throttling interrupt source
acd0: FAILURE - READ_BIG HARDWARE ERROR asc=0x08 ascq=0x03 error=0
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?163331489>