Date: Mon, 3 Apr 2006 23:10:19 GMT From: "Internet Partners, Inc. Tech Support" <support@ipinc.net> To: freebsd-bugs@FreeBSD.org Subject: Re: kern/89522: 6.0-RELEASE will not boot on some Compaqs with mouse connected Message-ID: <200604032310.k33NAJCm060646@freefall.freebsd.org>
next in thread | raw e-mail | index | archive | help
The following reply was made to PR kern/89522; it has been noted by GNATS. From: "Internet Partners, Inc. Tech Support" <support@ipinc.net> To: <bug-followup@FreeBSD.org>, <petefrench@ticketswitch.com> Cc: Subject: Re: kern/89522: 6.0-RELEASE will not boot on some Compaqs with mouse connected Date: Mon, 3 Apr 2006 16:04:28 -0700 On our Proliant 1600R the kernel does not boot even with the mouse disconnected. FreeBSD 4.11 works fine on this system. Here is a snippit of the kernel output on boot, this is with verbose logging selected, FreeBSD 6.0-RELEASE: . . . aic0: not probed (disabled) atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbdc: RESET_KBD return code:00fa kbdc: RESET_KBD status:00aa kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 atkbd0: [GIANT-LOCKED] psm0: current command byte:0065 kbdc: TEST_AUX_PORT status:0000 kbdc: RESET_AUX return code:0000 at this point it just freezes and the keyboard no longer responds to the 3 finger salute. Here is a snippit from an earlier boot on this machine with verbose NOT enabled (too much logging makes it scroll off the screen) . . . uhci0: <Intel 82371AB/EB (PIIX4) USB controller> at device 20.2 on pci0 uhci0: [GIANT LOCKED] usb0: <Intel 82371AB/EB (PIIX4) USB controller on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered . . . Speculation on the questions mailing list is that it is the USB controller. Ths server does NOT have any physical USB ports yet FreeBSD detects a USB chip. Linux has the same problem but with Linux you can disable the USB driver during the install, before it tries to load it. The BIOS does not allow disabling the mouse port on this system, it allows disabling the interrupt, but it still freezes. This system is a Compaq Proliant PL1600R 6/500 512 128 (dual 500MHZ cpus) The BIOS says nothing about USB. Here is the DMESG output from a FreeBSD 4.11 system on a Proliant 1600R with dual 450Mhz CPUs (very similar hardware). Note the failure to access the USB hardware: billmax# dmesg Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.11-RELEASE #0: Mon Nov 14 11:25:24 PST 2005 tedm@billmax.ipinc.net:/usr/src/sys/compile/BILLMAX Timecounter "i8254" frequency 1193182 Hz CPU: Pentium II/Pentium II Xeon/Celeron (448.95-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x652 Stepping = 2 Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA, CMOV,PAT,PSE36,MMX,FXSR> real memory = 536870912 (524288K bytes) avail memory = 518692864 (506536K bytes) Changing APIC ID for IO APIC #0 from 0 to 8 on chip Programming 35 pins in IOAPIC #0 IOAPIC #0 intpin 2 -> irq 0 FreeBSD/SMP: Multiprocessor motherboard: 2 CPUs cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000 cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000 io0 (APIC): apic id: 8, version: 0x00220011, at 0xfec00000 Preloaded elf kernel "kernel" at 0xc039c000. Pentium Pro MTRR support enabled md0: Malloc disk npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Intel 82443BX host to PCI bridge (AGP disabled)> on motherboard pci0: <PCI bus> on pcib0 pci0: <Cirrus Logic GD5446 SVGA controller> at 11.0 pcib1: <DEC 21150 PCI-PCI bridge> at device 13.0 on pci0 pci1: <PCI bus> on pcib1 tl0: <Compaq Netelligent 10/100 Proliant> port 0x2800-0x280f mem 0xc6ef9df0-0xc6ef9dff irq 9 at device 7.0 on pci1 tl0: Ethernet address: 00:08:c7:9f:92:77 miibus0: <MII bus> on tl0 nsphy0: <DP83840 10/100 media interface> on miibus0 nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto tlphy0: <ThunderLAN 10baseT media interface> on miibus0 tlphy0: 10base2/BNC, 10base5/AUI sym0: <875> port 0x2000-0x20ff mem 0xc6efb000-0xc6efbfff,0xc6ef9f00-0xc6ef9fff irq 10 at device 9.0 on pci1 sym0: No NVRAM, ID 7, Fast-20, SE, parity checking sym1: <875> port 0x2400-0x24ff mem 0xc6efa000-0xc6efafff,0xc6ef9e00-0xc6ef9eff irq 11 at device 9.1 on pci1 sym1: No NVRAM, ID 7, Fast-20, SE, parity checking pci1: <Matrox MGA Millennium 2064W graphics accelerator> at 13.0 irq 5 pci0: <unknown card> (vendor=0x0e11, dev=0xa0f0) at 14.0 pcib2: <IBM 82351 PCI-PCI bridge> at device 18.0 on pci0 pci2: <PCI bus> on pcib2 ida0: <Compaq SMART-2SL array controller> port 0x3000-0x30ff mem 0xb8000000-0xbfffffff,0xc6ffff00-0xc6ffffff irq 15 at device 0.0 on pci2 ida0: drives=1 firm_rev=4.44 idad0: <Compaq Logical Drive> on ida0 idad0: 26029MB (53309280 sectors), blocksize=512 isab0: <Intel 82371AB PCI to ISA bridge> at device 20.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 ATA33 controller> port 0xf100-0xf10f at device 20.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> irq 0 at device 20.2 on pci0 uhci0: Could not map ports device_probe_and_attach: uhci0 attach returned 6 piix0: <Intel 82371AB Power management controller> at device 20.3 on pci0 eisa0: <EISA bus> on motherboard mainboard0: <CPQ0689 (System Board)> on eisa0 slot 0 orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcbfff,0xe8000-0xedfff,0xee000-0xeffff on isa0 pmtimer0 on isa0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A APIC_IO: Testing 8254 interrupt delivery APIC_IO: routing 8254 via IOAPIC #0 intpin 2 SMP: AP CPU #1 Launched! acd0: CDROM <CD-ROM CDU701-Q> at ata0-master PIO4 Waiting 15 seconds for SCSI devices to settle sa0 at sym0 bus 0 target 6 lun 0 sa0: <HP C1537A L708> Removable Sequential Access SCSI-2 device sa0: 10.000MB/s transfers (10.000MHz, offset 16) Mounting root from ufs:/dev/idad0s1a IP packet filtering initialized, divert disabled, rule-based forwarding enabled, default to deny, logging disabled (sa0:sym0:0:6:0): WRITE FILEMARKS. CDB: 10 0 0 0 2 0 (sa0:sym0:0:6:0): Deferred Error: MEDIUM ERROR asc:3b,0 (sa0:sym0:0:6:0): Sequential positioning error billmax#
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200604032310.k33NAJCm060646>