Date: Fri, 30 Jan 2015 11:31:40 +0000 From: Ulrich Grey <usenet@ulrich-grey.de> To: Ulrich Grey <usenet@ulrich-grey.de> Cc: "freebsd-arm@freebsd.org List" <freebsd-arm@freebsd.org> Subject: Re: Beaglebone Black HDMI support v2 Message-ID: <20150130113140.6a1d46bfa3856170591c8a9b@ulrich-grey.de> In-Reply-To: <20150130103156.34dd4bd43ca62606f3f5b005@ulrich-grey.de> References: <AB68E490-CBB6-40A6-89FF-B410CBD65FD6@bluezbox.com> <20150130103156.34dd4bd43ca62606f3f5b005@ulrich-grey.de>
next in thread | previous in thread | raw e-mail | index | archive | help
In this case, the TV Set says: "Video Mode not Supported". Jan 30 11:04:24 beaglebone kernel: Product: [0470] SAMSUNG Jan 30 11:04:24 beaglebone kernel: Serial number: 00000000 Jan 30 11:04:24 beaglebone kernel: Manufactured 2008 Week 22 # Jan 30 11:04:24 beaglebone kernel: mmcsd1: 2GB <MMC MMC02G 3.10 SN 397DEBF7 MFG 08/1997 by 254 0x004e> at mmc1 48.0MHz/8bit/65535-block Jan 30 11:04:24 beaglebone kernel: am335x_pmic0: TPS65217C ver 1.2 powered by AC Jan 30 11:04:24 beaglebone kernel: tda0:TDA19988 Jan 30 11:04:24 beaglebone kernel: Vendor: [SAM] Samsung Jan 30 11:04:24 beaglebone kernel: Product: [0470] SAMSUNG Jan 30 11:04:24 beaglebone kernel: Serial number: 00000000 Jan 30 11:04:24 beaglebone kernel: Manufactured 2008 Week 22 Jan 30 11:04:24 beaglebone kernel: EDID Version 1.3 Jan 30 11:04:24 beaglebone kernel: EDID Comment: Jan 30 11:04:24 beaglebone kernel: Video Input: 80 Jan 30 11:04:24 beaglebone kernel: Digital Jan 30 11:04:24 beaglebone kernel: Gamma: 2.20 Jan 30 11:04:24 beaglebone kernel: Max Size: 16 cm x 9 cm Jan 30 11:04:24 beaglebone kernel: Features: a Jan 30 11:04:24 beaglebone kernel: RGB Jan 30 11:04:24 beaglebone kernel: Preferred timing Jan 30 11:04:24 beaglebone kernel: Chroma Info: Jan 30 11:04:24 beaglebone kernel: Red X: 0.639 Jan 30 11:04:24 beaglebone kernel: Red Y: 0.639 Jan 30 11:04:24 beaglebone kernel: Grn X: 0.299 Jan 30 11:04:24 beaglebone kernel: Grn Y: 0.599 Jan 30 11:04:24 beaglebone kernel: Blu X: 0.150 Jan 30 11:04:24 beaglebone kernel: Blu Y: 0.059 Jan 30 11:04:24 beaglebone kernel: Wht X: 0.312 Jan 30 11:04:24 beaglebone kernel: Wht Y: 0.329 Jan 30 11:04:24 beaglebone kernel: Range: Jan 30 11:04:24 beaglebone kernel: Horizontal: 26 - 68 kHz Jan 30 11:04:24 beaglebone kernel: Vertical: 23 - 61 Hz Jan 30 11:04:24 beaglebone kernel: Max Dot Clock: 230 MHz Jan 30 11:04:24 beaglebone kernel: Video modes: Jan 30 11:04:24 beaglebone kernel: 640x480 @ 60Hz (25175 656 752 800 490 492 525 -H -V) Jan 30 11:04:24 beaglebone kernel: 1920x1080 @ 60Hz (148500 2008 2052 2200 1084 1089 1125 +H +V) Jan 30 11:04:24 beaglebone kernel: 1280x720 @ 60Hz (74250 1390 1430 1650 725 730 750 +H +V) Jan 30 11:04:24 beaglebone kernel: Preferred mode: 1920x1080 @ 60Hz Jan 30 11:04:24 beaglebone kernel: Number of extension blocks: 1 Jan 30 11:04:24 beaglebone kernel: fb0: detected videomode: 1280x720 @ 60KHz Jan 30 11:04:24 beaglebone kernel: fbd0 on fb0 Jan 30 11:04:24 beaglebone kernel: VT: initialize with new VT driver "fb". > ---------------------------------- > On Wed, 28 Jan 2015 20:02:11 -0800 > Oleksandr Tymoshenko <gonzo@bluezbox.com> wrote: > > > Hello, > > > > Here is the second version of the patch: > > https://people.freebsd.org/~gonzo/arm/patches/bbb-hdmi-20150128.diff > > > > Changes comparing to previous version: > > > > - Config switched to vt(4) > > - EDID parser from NetBSD > > - Driver picks up the best matching videomode > > - ?naive? implementation of hdmi_if: HDMI connect events, read EDID, and set framer > > videomode. > > > > You need HEAD with r277871 for this patch to work reliably > > > > -- > > gonzo > > > > > > _______________________________________________ > > freebsd-arm@freebsd.org mailing list > > http://lists.freebsd.org/mailman/listinfo/freebsd-arm > > To unsubscribe, send any mail to "freebsd-arm-unsubscribe@freebsd.org" > _______________________________________________ > freebsd-arm@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-arm > To unsubscribe, send any mail to "freebsd-arm-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20150130113140.6a1d46bfa3856170591c8a9b>