Date: Fri, 23 Dec 2016 11:25:47 +0800 From: Ernie Luzar <luzar722@gmail.com> To: byrnejb@harte-lyne.ca Cc: freebsd-questions@freebsd.org Subject: Re: IP address assignments to jails using ezjail Message-ID: <585C993B.7040805@gmail.com> In-Reply-To: <b6c71debe36b214c620d4027ce6bec31.squirrel@webmail.harte-lyne.ca> References: <b6c71debe36b214c620d4027ce6bec31.squirrel@webmail.harte-lyne.ca>
next in thread | previous in thread | raw e-mail | index | archive | help
James B. Byrne via freebsd-questions wrote: > When I created the new jail I used this invocation: > > ezjail-admin create -x hlldrupal 'lo1|127.0.1.1,vtnet0|192.168.216.196' > > Inside the host rc.conf I have this: > > # Cloned i/f and assigned ipv4 addr for jails > cloned_interfaces="lo1" # For shared jail configuration > > And ifconfig on the host shows this: > > vtnet0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> > metric 0 mtu 1500 > options=80028<VLAN_MTU,JUMBO_MTU,LINKSTATE> > ether 00:a0:98:fa:aa:b6 > inet 216.185.71.16 netmask 0xffffff00 broadcast 216.185.71.255 > inet 192.168.216.16 netmask 0xffffff00 broadcast 192.168.216.255 > inet 192.168.216.196 netmask 0xffffffff broadcast 192.168.216.196 > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > media: Ethernet 10Gbase-T <full-duplex> > status: active > . . . > lo1: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 > options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6> > inet 127.0.1.1 netmask 0xffffffff > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > groups: lo > > Inside the jail ifconfig shows this: > > vtnet0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> > metric 0 mtu 1500 > options=80028<VLAN_MTU,JUMBO_MTU,LINKSTATE> > ether 00:a0:98:fa:aa:b6 > inet 192.168.216.196 netmask 0xffffffff broadcast 192.168.216.196 > media: Ethernet 10Gbase-T <full-duplex> > status: active > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 > options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6> > groups: lo > lo1: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 > options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6> > inet 127.0.1.1 netmask 0xffffffff > groups: lo > > > All this seems to be correct and yet I cannot seem to obtain an ssh > connection to or from the jailed instance. ubound is running in the > jail and seems to be working. At least host responds to queries. > > root@hlldrupal:~ # host sendmail.com > sendmail.com has address 209.246.26.25 > sendmail.com mail is handled by 10 mxa-00148501.gslb.pphosted.com. > sendmail.com mail is handled by 20 mx2.proofpoint.com. > sendmail.com mail is handled by 10 mxb-00148501.gslb.pphosted.com. > > pf is not running in the jail but sshd is: > > root@hlldrupal:~ # service sshd status > sshd is running as pid 81502. > > root@hlldrupal:~ # service pf status > Cannot 'status' pf. Set pf_enable to YES in /etc/rc.conf or use > 'onestatus' instead of 'status'. > root@hlldrupal:~ # service pf onestatus > pf.ko is not loaded > > > I note that the flag IFDISABLED is present on the host's lo1. Why? Is > this the source of the connectivity problem with the jail? If so then > why does the host commend work when executed within the jail? In any > case I can ping the jail from without: > > [root@vhost04 ~ (master *%)]# ping 192.168.216.196 > PING 192.168.216.196 (192.168.216.196) 56(84) bytes of data. > 64 bytes from 192.168.216.196: icmp_seq=1 ttl=64 time=0.647 ms > > I just cannot connect to that address via ssh from without nor can I > connect ssh to any address from within the jail. > > 1. Loopback is only necessary in a jail if that jail has a service running that uses it. But you have to modify that services config file to use the loopback ip address you assigned to the jail before things work correctly. lo1 is not necessary, can assign any 127.x.x.x ip address to the jail as long as you don't assign the hosts default 127.0.0.1 ip address. 2. I use qjail which is a fork of ezjail. It automatically configures your network for you so you don't have to manually add statements into rc.conf for your jails. Since this is a learning test anyway, give it a try. 3. Take ubound out of the mix by not starting that jail. Then use only ip addresses in your host to jail ssh command. 4. What is output of issuing host ssh command to a jail? Does host answer?
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?585C993B.7040805>