Date: Wed, 23 Aug 2000 13:18:11 +0200 From: Andreas Klemm <andreas@klemm.gtn.com> To: freebsd-stable@freebsd.org Subject: 4.1-STABLE panics on boot with Huyundai Laptop (P233) Message-ID: <20000823131811.A4418@titan.klemm.gtn.com>
next in thread | raw e-mail | index | archive | help
--yrj/dFKFPuw6o+aM Content-Type: text/plain; charset=us-ascii Content-Disposition: inline My Laptop only runs on FreeBSD 3.x. FreeBSD 4.0 4.1 4.1-STABLE 5.0-current -> only panic on boot. I compiled a kernel with DDB support. This are the last messages on screen: pci0: <PCI bus> on pcib0 isab0: <SiS 85c503 PCI-ISA bridge> at device 1.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Generic PCI ATA controller> port 0x3f4-0x3f7,0x374-0x377,0x1f4-0x1f7,0x174-0x177 at device 1.1 on pci0 atapci0: Busmasterinf DMA not supported ata-: ata2 exists, using next available unit number panic: resource_list_alloc: resource entry is busy Debugger<"panic"> trace shows the kernel functions that have been called so far. Debugger(...) at Debugger+0x34 panic(...) at panic+0x70 resource_list_alloc(...) pci_alloc_resource(...) BUS_ALLOC_RESOURCE(...) ata_pci_alloc_resource(...) BUS_ALLOC_RESOURCE(...) bus_alloc_resource(...) ata_probe(...) ata_pcisub_probe(...) DEVICE_PROBE(...) device_probe_child(...) device_probe_and_attach(...) bus_generic_attach(...) ata_pci_attach(...) DEVICE_ATTACH(...) device_probe_and_attach(...) bus_generic_attach(...) DEVICE_ATTACH(...) device_probe_and_attach(...) bus_generic_attach(...) DEVICE_ATTACH(...) device_probe_and_attach(...) bus_generic_attach(...) nexus_attach(...) DEVICE_ATTACH(...) device_probe_and_attach(...) root_bus_configure(...) configure(...) mi_startup(...) begin(...) In the attachement a session of booting FreeBSD 3.5-STABLE with boot_verbose and the kernel profile. Hope you can help. -- Andreas Klemm Powered by FreeBSD SMP Songs from our band >>64Bits<<............http://www.apsfilter.org/64bits.html My homepage................................ http://people.FreeBSD.ORG/~andreas Please note: Apsfilter got a NEW HOME................http://www.apsfilter.org/ --yrj/dFKFPuw6o+aM Content-Type: text/plain; charset=us-ascii Content-Disposition: attachment; filename="LAPTOP.dmesg" the University of California. All rights reserved. FreeBSD 3.5-STABLE #1: Wed Aug 23 12:12:27 CEST 2000 root@laptop.klemm.gtn.com:/usr/src/sys/compile/LAPTOP Calibrating clock(s) ... TSC clock: 232524334 Hz, i8254 clock: 1193168 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz CLK_USE_TSC_CALIBRATION not specified - using old calibration method CPU: Pentium/P55C (232.53-MHz 586-class CPU) Origin = "GenuineIntel" Id = 0x543 Stepping = 3 Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX> real memory = 67108864 (65536K bytes) Physical memory chunk(s): 0x00001000 - 0x0009efff, 647168 bytes (158 pages) 0x002d3000 - 0x03ffdfff, 64139264 bytes (15659 pages) avail memory = 62328832 (60868K bytes) Found BIOS32 Service Directory header at 0xc00ec050 Entry = 0xee600 (0xc00ee600) Rev = 0 Len = 1 PCI BIOS entry at 0x263e Other BIOS signatures found: ACPI: 00000000 $PnP: 000ff000 Preloaded elf kernel "kernel.ok" at 0xc02be000. pci_open(1): mode 1 addr port (0x0cf8) is 0x80000068 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=04061039) Probing for devices on PCI bus 0: found-> vendor=0x1039, dev=0x0406, revid=0x00 class=06-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 chip0: <SiS 85c501> rev 0x00 on pci0.0.0 found-> vendor=0x1039, dev=0x0008, revid=0x01 class=06-01-00, hdrtype=0x00, mfdev=1 subordinatebus=0 secondarybus=0 chip1: <SiS 85c503> rev 0x01 on pci0.1.0 found-> vendor=0x1039, dev=0x0601, revid=0x01 class=01-01-00, hdrtype=0x00, mfdev=1 subordinatebus=0 secondarybus=0 map[0]: type 4, range 32, base 00000174, size 2 map[1]: type 4, range 32, base 000001f4, size 2 map[2]: type 4, range 32, base 00000374, size 2 map[3]: type 4, range 32, base 000003f4, size 2 chip2: <SiS 85c601> rev 0x01 on pci0.1.1 found-> vendor=0x1023, dev=0x9660, revid=0xd3 class=03-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=255 map[0]: type 1, range 32, base 08000000, size 22 map[1]: type 1, range 32, base 08800000, size 16 map[2]: type 1, range 32, base 08400000, size 22 vga0: <Trident model 9660 VGA-compatible display device> rev 0xd3 int a irq 255 on pci0.6.0 found-> vendor=0x119b, dev=0x1221, revid=0x02 class=06-05-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=0 map[0]: type 4, range 32, base 000003e0, size 2 chip3: <PCI to PCMCIA bridge (vendor=119b device=1221)> rev 0x02 int a irq 0 on pci0.13.0 found-> vendor=0x119b, dev=0x1221, revid=0x02 class=06-05-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=0 map[0]: type 4, range 32, base 000003e4, size 2 chip4: <PCI to PCMCIA bridge (vendor=119b device=1221)> rev 0x02 int a irq 0 on pci0.14.0 Initializing PnP override table Probing for PnP devices: Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 No Plug-n-Play devices were found Probing for devices on the ISA bus: atkbd: the current kbd controller command byte 0067 atkbd: keyboard ID 0x41ab (2) kbdc: RESET_KBD return code:00fa kbdc: RESET_KBD status:00aa sc0 on isa sc0: fb0 kbd0 sc0: VGA color <8 virtual consoles, flags=0x0> atkbdc0 at 0x60-0x6f on motherboard atkbd0 irq 1 on isa kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 psm0: current command byte:0067 kbdc: TEST_AUX_PORT status:0000 kbdc: RESET_AUX return code:00fa kbdc: RESET_AUX status:00aa kbdc: RESET_AUX ID:0000 psm: status 00 02 64 psm: status 1c 03 3c psm: status 1c 03 3c psm: status 1c 03 3c psm: data 08 00 00 psm: status 10 00 64 psm: status 00 02 64 psm: data 08 00 00 psm: status 00 02 64 psm0 irq 12 on isa psm0: APM hooks installed. psm0: model Generic PS/2 mouse, device ID 0-00, 3 buttons psm0: config:00000000, flags:00000000, packet size:3 psm0: syncmask:c0, syncbits:00 sio0: irq maps: 0x9 0x19 0x9 0x9 sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa sio0: type 16550A sio1: irq maps: 0x1 0x9 0x1 0x1 sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A mss_probe: no address supplied, try default 0x530 mss_detect error, busy still set (0xff) sb_probe: no address supplied, try defaults (0x220,0x240) pcm0 at 0x220 irq 5 drq 1 on isa ESS1868 (rev 11) fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa fdc0: FIFO enabled, 8 bytes threshold fd0: 1.44MB 3.5in wdc0 at 0x1f0-0x1f7 irq 14 on isa wdc0: unit 0 (wd0): <HITACHI_DK237A-32> wd0: 3102MB (6354432 sectors), 6304 cyls, 16 heads, 63 S/T, 512 B/S wd0: ATA INQUIRE valid = 0007, dmamword = 0407, apio = 0003, udma = 0007 wdc1 at 0x170-0x177 irq 15 on isa wdc1: unit 0 (atapi): <CD-220EA/1.0A>, removable, accel, ovlap, dma, iordis wdc1: ATAPI CD-ROMs not configured ppc: parallel port found at 0x378 ppc: chipset forced to generic ppc0: EPP SPP ppc0 at 0x378 irq 7 flags 0x40 on isa ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode lpt0: <generic printer> on ppbus 0 lpt0: Interrupt-driven port ppi0: <generic parallel i/o> on ppbus 0 xe0 not found vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3b0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0x0 size:0k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff npx0 on motherboard npx0: INT 16 interface i586_bzero() bandwidth = 641436818 bytes/sec bzero() bandwidth = 331564986 bytes/sec apm0: disabled, not probed. imasks: bio c008c040, tty c003103a, net c0060080 device combination doesn't support shared irq3 intr_connect(irq3) failed, result=-1 device combination doesn't support shared irq4 intr_connect(irq4) failed, result=-1 device combination doesn't support shared irq5 intr_connect(irq5) failed, result=-1 device combination doesn't support shared irq7 intr_connect(irq7) failed, result=-1 device combination doesn't support shared irq12 intr_connect(irq12) failed, result=-1 device combination doesn't support shared irq14 intr_connect(irq14) failed, result=-1 device combination doesn't support shared irq15 intr_connect(irq15) failed, result=-1 PC-Card VLSI 82C146 (5 mem & 2 I/O windows) pcic: controller irq 9 Initializing PC-card drivers: xe sio BIOS Geometries: 0:03127f3f 0..786=787 cylinders, 0..127=128 heads, 1..63=63 sectors 1:03feff00 0..1022=1023 cylinders, 0..255=256 heads, 1..0=0 sectors 2:03fdfe3f 0..1021=1022 cylinders, 0..254=255 heads, 1..63=63 sectors 3:03fe0200 0..1022=1023 cylinders, 0..2=3 heads, 1..0=0 sectors 0 accounted for Device configuration finished. Intel Pentium detected, installing workaround for F00F bug IP packet filtering initialized, divert enabled, rule-based forwarding enabled, default to deny, logging limited to 100 packets/entry by default bpf: lo0 attached DUMMYNET initialized (000212) Considering FFS root f/s. changing root device to wd0s2a wd0s1: type 0xb, start 63, end = 3693311, size 3693249 : OK wd0s2: type 0xa5, start 3693312, end = 6354431, size 2661120 : OK start_init: trying /sbin/init Card inserted, slot 0 Card inserted, slot 1 xe0: Xircom CE3, bonding version 0x45, 100Mbps capable xe0: DingoID = 0x444b, RevisionID = 0, VendorID = 0 xe0: Ethernet address 00:80:c7:61:c2:9f bpf: xe0 attached pid 169 (ntpd), uid 0: exited on signal 12 (core dumped) Linux-ELF exec handler installed splash: image decoder found: logo_saver --yrj/dFKFPuw6o+aM Content-Type: text/plain; charset=us-ascii Content-Disposition: attachment; filename=LAPTOP machine "i386" cpu "I586_CPU" cpu "I686_CPU" ident LAPTOP maxusers 64 options INET #InterNETworking options FFS #Berkeley Fast Filesystem options FFS_ROOT #FFS usable as root device [keep this!] options MFS #Memory Filesystem options NFS #Network Filesystem options MSDOSFS #MSDOS Filesystem options "CD9660" #ISO 9660 Filesystem options PROCFS #Process filesystem options "COMPAT_43" #Compatible with BSD 4.3 [KEEP THIS!] options UCONSOLE #Allow users to grab the console options KTRACE #ktrace(1) syscall trace support options SYSVSHM #SYSV-style shared memory options SYSVMSG #SYSV-style message queues options SYSVSEM #SYSV-style semaphores config kernel root on wd0 controller isa0 controller pnp0 # PnP support for ISA controller pci0 # Floppy drives controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2 disk fd0 at fdc0 drive 0 # IDE controller and disks options "CMD640" # work around CMD640 chip deficiency controller wdc0 at isa? port "IO_WD1" bio irq 14 disk wd0 at wdc0 drive 0 disk wd1 at wdc0 drive 1 controller wdc1 at isa? port "IO_WD2" bio irq 15 disk wd2 at wdc1 drive 0 disk wd3 at wdc1 drive 1 # ATAPI devices options ATAPI #Enable ATAPI support for IDE bus options ATAPI_STATIC #Don't do it as an LKM # atkbdc0 controls both the keyboard and the PS/2 mouse controller atkbdc0 at isa? port IO_KBD tty device atkbd0 at isa? tty irq 1 device psm0 at isa? tty irq 12 device vga0 at isa? port ? conflicts # splash screen/screen saver pseudo-device splash # syscons is the default console driver, resembling an SCO console device sc0 at isa? tty # Floating point support - do not disable. device npx0 at isa? port IO_NPX irq 13 # Power management support (see LINT for more options) device apm0 at isa? disable flags 0x31 # Advanced Power Management # PCCARD (PCMCIA) support controller card0 device pcic0 at card? device pcic1 at card? # Serial (COM) ports device sio0 at isa? port "IO_COM1" flags 0x10 tty irq 4 device sio1 at isa? port "IO_COM2" tty irq 3 # Parallel port # # Note: The ppc0 entry is configured to support networking over the # parallel port. If you will be using it for printing, change # "net" to "tty", and review ppc(4) to ensure you have the # correct flags value. device ppc0 at isa? port? flags 0x40 net irq 7 controller ppbus0 # Parallel port bus (required) device lpt0 at ppbus? # Printer device ppi0 at ppbus? # Parallel port interface device #device plip0 at ppbus? # TCP/IP over parallel # requires PCCARD (PCMCIA) support to be activated device xe0 at isa? port? net irq ? # Pseudo devices - the number indicates how many units to allocated. pseudo-device loop # Network loopback pseudo-device ether # Ethernet support #pseudo-device sl 1 # Kernel SLIP #pseudo-device ppp 1 # Kernel PPP #pseudo-device tun 1 # Packet tunnel pseudo-device pty 16 # Pseudo-ttys (telnet etc) pseudo-device gzip # Exec gzipped a.out's # The `bpfilter' pseudo-device enables the Berkeley Packet Filter. # Be aware of the administrative consequences of enabling this! # The number of devices determines the maximum number of # simultaneous BPF clients programs runnable. pseudo-device bpfilter 1 #Berkeley packet filter options MROUTING # Multicast routing options IPFIREWALL #firewall options IPFIREWALL_VERBOSE #print information about dropped packets options IPFIREWALL_FORWARD #enable transparent proxy support options "IPFIREWALL_VERBOSE_LIMIT=100" #limit verbosity options IPDIVERT #divert sockets options IPSTEALTH #support for stealth forwarding options "ICMP_BANDLIM" options DUMMYNET options SOFTUPDATES options MAXCONS=8 # number of virtual consoles options SC_HISTORY_SIZE=512 # number of history buffer lines device pcm0 at isa? port ? tty irq 5 drq 1 flags 0x0 options SHOW_BUSYBUFS # List buffers that prevent root unmount options DDB --yrj/dFKFPuw6o+aM-- To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20000823131811.A4418>