Skip site navigation (1)Skip section navigation (2)
Date:      Tue, 24 Jan 2012 23:52:31 -0800
From:      Adrian Chadd <adrian@freebsd.org>
To:        =?UTF-8?Q?Michal_Van=C4=8Do?= <mvanco@di-vision.sk>
Cc:        freebsd-wireless@freebsd.org, freebsd-stable@freebsd.org
Subject:   Re: ath0: device timeout on 9.0-STABLE
Message-ID:  <CAJ-VmokEuhvO458r7=hjcxZx3XkmPCmZx_=TM9%2Bpj1AeHvX00Q@mail.gmail.com>
In-Reply-To: <A08F9265-8CF7-4180-BB19-BDACFDC8AE3E@di-vision.sk>
References:  <43606099-9A1E-4B56-87FB-FB1CD23E9A8F@di-vision.sk> <CAJ-Vmon23eKpj6kUx5L50CPsP5KWayeZM68Jr5Qo2ynC8mYOnQ@mail.gmail.com> <A08F9265-8CF7-4180-BB19-BDACFDC8AE3E@di-vision.sk>

next in thread | previous in thread | raw e-mail | index | archive | help
Hi,

The LED stuff may be a bit broken for 9.0. I'll try to fix it up and
backport the GPIO and LED fixes.


Adrian

On 24 January 2012 23:51, Michal Van=C4=8Do <mvanco@di-vision.sk> wrote:

> Adrian,
>
> believe or not =E2=80=A6 it simply started to work. I just left my thinkp=
ad turned
> off during the night and now when I booted, almost everything works as
> expected:
>
> # ifconfig wlan0
> wlan0: flags=3D8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu =
1500
>        ether 00:19:7e:52:1c:c4
>        inet 192.168.0.17 netmask 0xffffff00 broadcast 192.168.0.255
>        nd6 options=3D29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
>        media: IEEE 802.11 Wireless Ethernet OFDM/48Mbps mode 11g
>        status: associated
>        ssid XXX channel 9 (2452 MHz 11g) bssid 10:9a:dd:88:2a:5d
>        regdomain ETSI2 country SK indoor ecm authmode WPA2/802.11i
>        privacy ON deftxkey UNDEF AES-CCM 3:128-bit txpower 30 bmiss 7
>        scanvalid 450 bgscan bgscanintvl 300 bgscanidle 250 roam:rssi 7
>        roam:rate 5 protmode CTS wme burst roaming MANUAL
>
> # /usr/src/tools/tools/ath/athstats/athstats -i ath0
> 4228     data frames received
> 818      data frames transmit
> 3        tx frames with an alternate rate
> 126      long on-chip tx retries
> 29480    mib overflow interrupts
> 24M      current transmit rate
> 730      tx frames with short preamble
> 210      rx failed 'cuz of bad CRC
> 18       rx failed 'cuz of PHY err
>    18       CCK restart
> 10       periodic calibrations
> -0/+0    TDMA slot adjust (usecs, smoothed)
> 37       rssi of last ack
> 37       avg recv rssi
> -96      rx noise floor
> 90       tx frames through raw api
> 1        spur immunity level
> 1        first step level
> 9        ANI increased spur immunity
> 2        ANI decrease spur immunity
> 103      ANI enabled OFDM weak signal detect
> 4        ANI disabled OFDM weak signal detect
> 102      ANI disabled CCK weak signal threshold
> 3        ANI increased first step level
> 7392282  cumulative OFDM phy error count
> 34526    cumulative CCK phy error count
> 20       ANI forced listen time to zero
> 126      missing ACK's
> 291      bad FCS
> 2928     beacons received
> 39       average rssi (beacons only)
> 37       average rssi (all rx'd frames)
> 37       average rssi (ACKs only)
> Antenna profile:
> [0] tx      817 rx       65
> [1] tx        0 rx     4163
>
> I say "almost" because that small WiFi-LED doesn't blink as it should. Is
> there any way to fix this? I see these sysctls:
>
> dev.ath.0.softled: 0
> dev.ath.0.ledpin: 0
> dev.ath.0.ledon: 0
> dev.ath.0.ledidle: 2700
>
> but I'm lost with them :)
>
> regards
> michal
>
> On 25.1.2012, at 4:46, Adrian Chadd wrote:
>
> > Sure, can you please:
> >
> > * compile with the following options:
> >
> > options ATH_DEBUG
> > options AH_DEBUG
> > options ATH_DIAGAPI
> >
> > * compile /usr/src/sys/tools/tools/ath/athstats/
> >
> > * run athstats -i ath0 and email them to me +
> freebsd-wireless@freebsd.org
> >
> > Thanks!
> >
> >
> >
> > Adrian
> >
> >
> > On 24 January 2012 04:01, Michal Van=C4=8Do <mvanco@di-vision.sk> wrote=
:
> > Hi there,
> >
> > I've installed 9.0-STABLE (also tried on 9.0-RELEASE) on my Thinkpad T6=
0
> and I'm not able to use WiFi. Kernel is GENERIC.
> >
> > pciconf -lv:
> > ath0@pci0:3:0:0:        class=3D0x028000 card=3D0x0033168c chip=3D0x002=
4168c
> rev=3D0x01 hdr=3D0x00
> >    vendor     =3D 'Atheros Communications Inc.'
> >    device     =3D 'AR5008 Wireless Network Adapter'
> >    class      =3D network
> >
> > relevant part of rc.conf:
> > wlans_ath0=3D"wlan0"
> > create_args_wlan0=3D"country SK"
> > ifconfig_wlan0=3D"WPA DHCP"
> >
> > and wpa_supplicant.conf:
> > ctrl_interface=3D/var/run/wpa_supplicant
> >
> > network=3D{
> >        ssid=3D"XXX"
> >        psk=3D"XXX"
> > }
> >
> > dmesg just fills with "ath0: device timeout" messages and wifi just
> doesn't work.
> >
> > any clue?
> >
> > regards
> > michal
> >
> > _______________________________________________
> > freebsd-stable@freebsd.org mailing list
> > http://lists.freebsd.org/mailman/listinfo/freebsd-stable
> > To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.or=
g
> "
> >
>
> _______________________________________________
> freebsd-stable@freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
> To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org"
>



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CAJ-VmokEuhvO458r7=hjcxZx3XkmPCmZx_=TM9%2Bpj1AeHvX00Q>