Date: Fri, 6 Mar 2015 13:58:58 +0530 From: Manish Jain <bourne.identity@hotmail.com> To: CyberLeo Kitsana <cyberleo@cyberleo.net> Cc: freebsd-questions@freebsd.org Subject: Re: Is there any plan to adopt devtmpfs ? Message-ID: <BLU436-SMTP74AE6E33F834A2D406AE1BF61C0@phx.gbl> In-Reply-To: <54F88D64.4000607@cyberleo.net> References: <BLU436-SMTP37B91369BA1F4532599758F61F0@phx.gbl> <54F88D64.4000607@cyberleo.net>
next in thread | previous in thread | raw e-mail | index | archive | help
>> Can you provide further details for these failures? Specific device
>> models and relevant dmesg(8) and usbconfig(8) output, for example.
>>
I have something for the APC UPS (USB Powerchute) too. Again, the
complete output of dmesg is attached below my signature.
1)
Important lines from my /etc/rc.conf :
apcupsd_enable="NO" #Needed to run apctest
dbus_enable="YES"
hald_enable="YES"
devfs_system_ruleset="system"
2)
Important lines from my /usr/local/etc/apcupsd/apcupsd.conf :
UPSNAME APC700BE
UPSCABLE usb
UPSTYPE usb
DEVICE
BATTERYLEVEL 5
MINUTES 5
UPSCLASS standalone
UPSNAME APC700BE
BATTDATE 05/28/14
SENSITIVITY L
3)
usbconfig -u 2 dump_info
ugen2.1: <EHCI root HUB ATI> at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps)
pwr=SAVE (0mA)
ugen2.2: <USB 2.0 Hub vendor 0x1a40> at usbus2, cfg=0 md=HOST spd=HIGH
(480Mbps) pwr=SAVE (100mA)
ugen2.3: <USB Optical Mouse Logitech> at usbus2, cfg=0 md=HOST spd=LOW
(1.5Mbps) pwr=ON (100mA)
ugen2.4: <USB Keyboard Logitech> at usbus2, cfg=0 md=HOST spd=LOW
(1.5Mbps) pwr=ON (90mA)
ugen2.5: <Back-UPS ES 700Y-IN FW895.m1.I USB FWm1 American Power
Conversion> at usbus2, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (2mA)
ugen2.5: <Back-UPS ES 700Y-IN FW895.m1.I USB FWm1 American Power
Conversion> at usbus2, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (2mA)
4)
usbconfig -u 2 -a 5 dump_device_desc
bLength = 0x0012
bDescriptorType = 0x0001
bcdUSB = 0x0110
bDeviceClass = 0x0000
bDeviceSubClass = 0x0000
bDeviceProtocol = 0x0000
bMaxPacketSize0 = 0x0008
idVendor = 0x051d
idProduct = 0x0002
bcdDevice = 0x0006
iManufacturer = 0x0003 <American Power Conversion>
iProduct = 0x0001 <Back-UPS ES 700Y-IN FW:895.m1.I USB FW:m1>
iSerialNumber = 0x0002 <E21251005365 >
bNumConfigurations = 0x0001
5)
This is what I get in apctest.output when I run apctest :
#{//start output
2015-03-06 11:43:17 apctest 3.14.12 (29 March 2014) freebsd
Checking configuration ...
sharenet.type = Network & ShareUPS Disabled
cable.type = USB Cable
mode.type = USB UPS Driver
Setting up the port ...
Doing prep_device() ...
You are using a USB cable type, so I'm entering USB test mode
Hello, this is the apcupsd Cable Test program.
This part of apctest is for testing USB UPSes.
Getting UPS capabilities...SUCCESS
Please select the function you want to perform.
1) Test kill UPS power
2) Perform self-test
3) Read last self-test result
4) View/Change battery date
5) View manufacturing date
6) View/Change alarm behavior
7) View/Change sensitivity
8) View/Change low transfer voltage
9) View/Change high transfer voltage
10) Perform battery calibration
11) Test alarm
12) View/Change self-test interval
Q) Quit
Select function number: 2
This test instructs the UPS to perform a self-test
operation and reports the result when the test completes.
Clearing previous self test result...CLEARED
Initiating self test...INITIATED
Waiting for test to complete...COMPLETED
Result of last self test: PASSED
1) Test kill UPS power
2) Perform self-test
3) Read last self-test result
4) View/Change battery date
5) View manufacturing date
6) View/Change alarm behavior
7) View/Change sensitivity
8) View/Change low transfer voltage
9) View/Change high transfer voltage
10) Perform battery calibration
11) Test alarm
12) View/Change self-test interval
Q) Quit
Select function number: 4
Current battery date: 05/28/2014
Enter new battery date (MM/DD/YYYY), blank to quit:
Invalid format.
1) Test kill UPS power
2) Perform self-test
3) Read last self-test result
4) View/Change battery date
5) View manufacturing date
6) View/Change alarm behavior
7) View/Change sensitivity
8) View/Change low transfer voltage
9) View/Change high transfer voltage
10) Perform battery calibration
11) Test alarm
12) View/Change self-test interval
Q) Quit
Select function number: 7
Current sensitivity setting: MEDIUM
Press...
L for Low sensitivity
M for Medium sensitivity
H for High sensitivity
Q to Quit with no changes
Your choice: Select function: M
New sensitivity setting: MEDIUM
1) Test kill UPS power
2) Perform self-test
3) Read last self-test result
4) View/Change battery date
5) View manufacturing date
6) View/Change alarm behavior
7) View/Change sensitivity
8) View/Change low transfer voltage
9) View/Change high transfer voltage
10) Perform battery calibration
11) Test alarm
12) View/Change self-test interval
Q) Quit
Select function number: 10
This test instructs the UPS to perform a battery calibration
operation and reports the result when the process completes.
The battery level must be at 100% and the load must be at least
10% to begin this test.
Failed to read current battery level
#}//end output
6)
Running /usr/local/etc/apcupsd/commfailure fails :
/usr/local/etc/apcupsd # ./commfailure
./commfailure: -s: not found
Error contacting apcupsd @ localhost:3551: Connection refused
Regards
Manish Jain
#here is the complete dmesg :
Copyright (c) 1992-2014 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.1-RELEASE #0 r274401: Tue Nov 11 22:51:51 UTC 2014
root@releng1.nyi.freebsd.org:/usr/obj/usr/src/sys/GENERIC i386
FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512
CPU: AMD Athlon(tm) II X2 270 Processor (3415.41-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x100f63 Family = 0x10 Model = 0x6
Stepping = 3
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Features2=0x802009<SSE3,MON,CX16,POPCNT>
AMD
Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM,3DNow!+,3DNow!>
AMD
Features2=0x837ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT,NodeId>
TSC: P-state invariant
real memory = 2147483648 (2048 MB)
avail memory = 1819914240 (1735 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <090412 APIC1527>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has zero
address or length: 0x0000000000000000/0x1 (20130823/tbfadt-630)
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
random: <Software, Yarrow> initialized
acpi0: <090412 XSDT1527> on motherboard
acpi0: Power Button (fixed)
acpi0: reservation of fee00000, 1000 (3) failed
acpi0: reservation of ffb80000, 80000 (3) failed
acpi0: reservation of fec10000, 20 (3) failed
acpi0: reservation of fed40000, 5000 (3) failed
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, 6fe00000 (3) failed
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 550
Event timer "HPET1" frequency 14318180 Hz quality 450
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xd000-0xd0ff mem
0xd0000000-0xdfffffff,0xfebe0000-0xfebeffff,0xfea00000-0xfeafffff irq 18
at device 5.0 on pci1
vgapci0: Boot video device
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 4.0 on pci0
pci2: <ACPI PCI bus> on pcib2
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port
0xe800-0xe8ff mem 0xfdfff000-0xfdffffff,0xfdff8000-0xfdffbfff irq 16 at
device 0.0 on pci2
re0: Using 1 MSI-X message
re0: Chip rev. 0x2c800000
re0: MAC rev. 0x00100000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX,
100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master,
1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow,
1000baseT-FDX-flow-master, auto, auto-flow
re0: Ethernet address: 50:46:5d:66:fd:10
ahci0: <AMD SB7x0/SB8x0/SB9x0 AHCI SATA controller> port
0xc000-0xc007,0xb000-0xb003,0xa000-0xa007,0x9000-0x9003,0x8000-0x800f
mem 0xfe9ffc00-0xfe9fffff irq 22 at device 17.0 on pci0
ahci0: AHCI v1.10 with 4 3Gbps ports, Port Multiplier supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich2: <AHCI channel> at channel 2 on ahci0
ahcich3: <AHCI channel> at channel 3 on ahci0
ohci0: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe9fe000-0xfe9fefff
irq 16 at device 18.0 on pci0
usbus0 on ohci0
ohci1: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe9fd000-0xfe9fdfff
irq 16 at device 18.1 on pci0
usbus1 on ohci1
ehci0: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem
0xfe9ff800-0xfe9ff8ff irq 17 at device 18.2 on pci0
usbus2: EHCI version 1.0
usbus2 on ehci0
ohci2: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe9fc000-0xfe9fcfff
irq 18 at device 19.0 on pci0
usbus3 on ohci2
ohci3: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe9fb000-0xfe9fbfff
irq 18 at device 19.1 on pci0
usbus4 on ohci3
ehci1: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem
0xfe9ff400-0xfe9ff4ff irq 19 at device 19.2 on pci0
usbus5: EHCI version 1.0
usbus5 on ehci1
atapci0: <ATI IXP700/800 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on pci0
ata0: <ATA channel> at channel 0 on atapci0
ata1: <ATA channel> at channel 1 on atapci0
hdac0: <ATI SB600 HDA Controller> mem 0xfe9f4000-0xfe9f7fff irq 16 at
device 20.2 on pci0
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib3: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci3: <ACPI PCI bus> on pcib3
ohci4: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe9fa000-0xfe9fafff
irq 18 at device 20.5 on pci0
usbus6 on ohci4
acpi_button0: <Power Button> on acpi0
ppc0: <Parallel port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
acpi_throttle0: <ACPI CPU Throttling> on cpu0
hwpstate0: <Cool`n'Quiet 2.0> on cpu0
Timecounters tick every 1.000 msec
hdacc0: <Realtek ALC887 HDA CODEC> at cad 0 on hdac0
hdaa0: <Realtek ALC887 Audio Function Group> at nid 1 on hdacc0
pcm0: <Realtek ALC887 (Rear Analog)> at nid 20 and 24,26 on hdaa0
pcm1: <Realtek ALC887 (Front Analog)> at nid 27 and 25 on hdaa0
pcm2: <Realtek ALC887 (Onboard Digital)> at nid 17 on hdaa0
random: unblocking device.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 480Mbps High Speed USB v2.0
usbus6: 12Mbps Full Speed USB v1.0
ugen5.1: <ATI> at usbus5
uhub0: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus5
ugen4.1: <ATI> at usbus4
uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen3.1: <ATI> at usbus3
uhub2: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen2.1: <ATI> at usbus2
uhub3: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen1.1: <ATI> at usbus1
uhub4: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen0.1: <ATI> at usbus0
uhub5: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen6.1: <ATI> at usbus6
uhub6: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
uhub6: 2 ports with 2 removable, self powered
uhub1: 3 ports with 3 removable, self powered
uhub2: 3 ports with 3 removable, self powered
uhub4: 3 ports with 3 removable, self powered
uhub5: 3 ports with 3 removable, self powered
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
ada0: <WDC WD3200AAJS-00L7A0 01.03E01> ATA-8 SATA 1.x device
ada0: Serial Number WD-WMAV27542837
ada0: 150.000MB/s transfers (SATA 1.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 305244MB (625140335 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad4
ada1 at ahcich1 bus 0 scbus1 target 0 lun 0
ada1: <WDC WD1600AAJS-00V4A0 05.01D05> ATA-8 SATA 2.x device
ada1: Serial Number WD-WCAWF6026337
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 152626MB (312579695 512 byte sectors: 16H 63S/T 16383C)
ada1: Previously was known as ad6
cd0 at ahcich2 bus 0 scbus2 target 0 lun 0
cd0: <HP DVD Writer 1260v AH24> Removable CD-ROM SCSI-0 device
cd0: Serial Number 3524497 206238502323
cd0: 150.000MB/s transfers (SATA 1.x, UDMA5, ATAPI 12bytes, PIO 8192bytes)
cd0: Attempt to query device size failed: NOT READY, Medium not present
- tray closed
SMP: AP CPU #1 Launched!
Timecounter "TSC-low" frequency 1707704409 Hz quality 800
uhub0: 6 ports with 6 removable, self powered
uhub3: 6 ports with 6 removable, self powered
Root mount waiting for: usbus2
ugen2.2: <vendor 0x1a40> at usbus2
uhub7: <vendor 0x1a40 USB 2.0 Hub, class 9/0, rev 2.00/1.11, addr 2> on
usbus2
Root mount waiting for: usbus2
uhub7: 4 ports with 4 removable, self powered
ugen2.3: <Logitech> at usbus2
Root mount waiting for: usbus2
ugen2.4: <Logitech> at usbus2
ukbd0: <USB Keyboard> on usbus2
kbd2 at ukbd0
Root mount waiting for: usbus2
ugen2.5: <American Power Conversion> at usbus2
Trying to mount root from ufs:/dev/ada0s1a [rw]...
ums0: <Logitech USB Optical Mouse, class 0/0, rev 2.00/72.00, addr 3> on
usbus2
ums0: 3 buttons and [XYZ] coordinates ID=0
uhid0: <USB Keyboard> on usbus2
fuse-freebsd: version 0.4.4, FUSE ABI 7.8
info: [drm] Initialized drm 1.1.0 20060810
drmn0: <ATI Radeon 3000 Graphics> on vgapci0
info: [drm] RADEON_IS_PCI
info: [drm] initializing kernel modesetting (RS780 0x1002:0x9616
0x1043:0x8388).
info: [drm] register mmio base: 0xFEBE0000
info: [drm] register mmio size: 65536
info: [drm] radeon_atrm_get_bios: ===> Try ATRM...
info: [drm] radeon_atrm_get_bios: IGP card detected, skipping this method...
info: [drm] radeon_acpi_vfct_bios: ===> Try VFCT...
info: [drm] radeon_acpi_vfct_bios: Get "VFCT" ACPI table
info: [drm] radeon_acpi_vfct_bios: Failed to get "VFCT" table: AE_NOT_FOUND
info: [drm] igp_read_bios_from_vram: ===> Try IGP's VRAM...
info: [drm] igp_read_bios_from_vram: VRAM base address: 0xd0000000
info: [drm] igp_read_bios_from_vram: Map address: 0xf021f000 (262144 bytes)
info: [drm] igp_read_bios_from_vram: Incorrect BIOS signature: 0x5307
info: [drm] radeon_read_bios: ===> Try PCI Expansion ROM...
info: [drm] radeon_read_bios: Map address: 0xc00c0000 (131072 bytes)
info: [drm] ATOM BIOS: B27722_RS780C
drmn0: info: VRAM: 256M 0x00000000C0000000 - 0x00000000CFFFFFFF (256M used)
drmn0: info: GTT: 512M 0x00000000A0000000 - 0x00000000BFFFFFFF
info: [drm] Detected VRAM RAM=256M, BAR=256M
info: [drm] RAM width 32bits DDR
[TTM] Zone kernel: Available graphics memory: 906222 kiB
[TTM] Initializing pool allocator
info: [drm] radeon: 256M of VRAM memory ready
info: [drm] radeon: 512M of GTT memory ready.
info: [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
info: [drm] Driver supports precise vblank timestamp query.
info: [drm] radeon: irq initialized.
info: [drm] GART: num cpu pages 131072, num gpu pages 131072
info: [drm] Loading RS780 Microcode
info: [drm] PCIE GART of 512M enabled (table at 0x00000000C0040000).
drmn0: info: WB enabled
drmn0: info: fence driver on ring 0 use gpu addr 0x00000000a0000c00 and
cpu addr 0x0xec6dcc00
drmn0: info: fence driver on ring 3 use gpu addr 0x00000000a0000c0c and
cpu addr 0x0xec6dcc0c
info: [drm] ring test on 0 succeeded in 1 usecs
info: [drm] ring test on 3 succeeded in 1 usecs
info: [drm] ib test on ring 0 succeeded in 0 usecs
info: [drm] ib test on ring 3 succeeded in 0 usecs
info: [drm] radeon_device_init: Taking over the fictitious range
0xd0000000-0xe0000000
iicbus0: <Philips I2C bus> on iicbb0 addr 0xf0
iic0: <I2C generic I/O> on iicbus0
iicbus1: <Philips I2C bus> on iicbb1 addr 0xc7
iic1: <I2C generic I/O> on iicbus1
iicbus2: <Philips I2C bus> on iicbb2 addr 0xc7
iic2: <I2C generic I/O> on iicbus2
iicbus3: <Philips I2C bus> on iicbb3 addr 0xc7
iic3: <I2C generic I/O> on iicbus3
iicbus4: <Philips I2C bus> on iicbb4 addr 0xc7
iic4: <I2C generic I/O> on iicbus4
info: [drm] Radeon Display Connectors
info: [drm] Connector 0:
info: [drm] VGA-1
info: [drm] DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c 0x7e4c
info: [drm] Encoders:
info: [drm] CRT1: INTERNAL_KLDSCP_DAC1
info: [drm] Connector 1:
info: [drm] DVI-D-1
info: [drm] HPD1
info: [drm] DDC: 0x7e50 0x7e50 0x7e54 0x7e54 0x7e58 0x7e58 0x7e5c 0x7e5c
info: [drm] Encoders:
info: [drm] DFP3: INTERNAL_KLDSCP_LVTMA
info: [drm] radeon: power management initialized
info: [drm] fb mappable at 0xD0142000
info: [drm] vram apper at 0xD0000000
info: [drm] size 5787648
info: [drm] fb depth is 24
info: [drm] pitch is 6400
fbd0 on drmn0
info: [drm] Initialized radeon 2.29.0 20080528
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?BLU436-SMTP74AE6E33F834A2D406AE1BF61C0>