Date: Thu, 26 Mar 2015 16:16:48 +1100 (EST) From: Ian Smith <smithi@nimnet.asn.au> To: Da Rock <freebsd-acpi@herveybayaustralia.com.au> Cc: "freebsd-acpi@freebsd.org" <freebsd-acpi@freebsd.org> Subject: Re: HP Compaq CQ62/42 acpi Message-ID: <20150326144735.L22893@sola.nimnet.asn.au> In-Reply-To: <551362EF.3080801@herveybayaustralia.com.au> References: <55113B2D.2040609@herveybayaustralia.com.au> <CAN6yY1vs=M_1PWRq5pSiuczQc7hXqm333gtkHDPv5Vdc64k3Gg@mail.gmail.com> <551362EF.3080801@herveybayaustralia.com.au>
next in thread | previous in thread | raw e-mail | index | archive | help
On Thu, 26 Mar 2015 11:37:51 +1000, Da Rock wrote: > On 03/25/15 09:52, Kevin Oberman wrote: > > On Tue, Mar 24, 2015 at 3:23 AM, Da Rock > > <freebsd-acpi@herveybayaustralia.com.au > > <mailto:freebsd-acpi@herveybayaustralia.com.au>> wrote: > > > > I have 2 laptops as mentioned, 3 all amd athlon based. The 3rd is > > an asus which I'm relatively happy with. > > > > What I have is when I pull the AC out of it, the sysctl for cpu > > speed goes from 2200 to 100 or 400. Basically the system becomes > > rather unusable. > > > > I tried the acpi_hp module, and it now switches to 800. This is > > better, but barely usable still. > > > > I'd like to see a response similar to the asus if its possible; > > this effectively stays the same, but drops speed if nothing is > > happening. > > > > Ideally, I'd think that it would be better if the system adjusted > > speed to use requirements during operation, but neither does that. > > I suspect that the asus should (in theory) as it does do it on > > battery only; but unless I'm really hammering all the time, it > > just doesn't seem to happen when I'm looking at it. > > > > The settings used on all for powerd is hiadaptive for AC, adaptive > > for battery. > > > > If I'm doing something wrong let me know, if more data is required > > I'm happy to help the cause :) > > > > TIA > > > > First, let's get a bit more information. Please provide: > > sysctl dev.cpu.0 (on AC and then on battery) > AC: > > dev.cpu.0.%desc: ACPI CPU > dev.cpu.0.%driver: cpu > dev.cpu.0.%location: handle=\_PR_.C000 > dev.cpu.0.%pnpinfo: _HID=none _UID=0 > dev.cpu.0.%parent: acpi0 > dev.cpu.0.temperature: 85.3C > dev.cpu.0.freq: 200 > dev.cpu.0.freq_levels: 2200/7543 1925/6600 1900/6150 1662/5381 1600/4777 > 1400/4179 1300/3750 1137/3281 975/2812 800/2091 700/1829 600/1568 500/1306 > 400/1045 300/784 200/522 100/261 > dev.cpu.0.cx_supported: C1/1/0 > dev.cpu.0.cx_lowest: C1 > dev.cpu.0.cx_usage: 100.00% last 682us Kevin appears to be psychic :) as for the second time in 3 days has replied while I was composing mine, but this time I heard the beep and saw 'new message from Kevin ..' and of course he's well covered it, except possibly regarding one aspect which I'll leave in: The clue is all those freq_levels. For powerd to increase frequeny under load requires stepping through all of them, possibly one per polling interval, which as you've observed takes too long. If you were running Intel I'd say you need to add to /boot/loader.conf these, and you should add them anyway: hint.p4tcc.0.disabled=1 hint.acpi_throttle.0.disabled=1 But from your one (1) clue that this is an AMD system, I'm not so sure: > amdtemp0: <AMD CPU On-Die Thermal Sensors> on hostb4 so you should check dmesg to check if you're running powernow(none!) instead of est(4) plus any other drivers providing 'thermal control', and if so, disable it (but not powernow or amdtemp) similarly. It may already be using acpi_throttle?, or perhaps p4tcc also covers AMD CPUs these days, I'm not sure? If that's unclear, post /var/run/dmesg.boot Yes, set both *_cx_lowest=Cmax and take delight in dev.cpu.0.cx_usage Playing with powerd_flags can make quite a lot of difference to powerd's behaviour, so I echo Kevin's request to see those, and his advice to run powerd -v in a terminal while you play, especially with -i and -r flags, though reducing -p interval may be beneficial to responsiveness, at a slight increase in powerd's CPU usage. I don't know if any of this changed between your 10.0 and 10.1 .. cheers, Ian
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20150326144735.L22893>