Date: Mon, 12 Dec 2005 08:27:06 -0600 From: "Keith Bottner" <keith@barkinglizards.com> To: "'Robert Marella'" <rmarella@gmail.com> Cc: 'FreeBSD Questions' <freebsd-questions@freebsd.org> Subject: RE: Detect hardware changes Message-ID: <014901c5ff28$2174bac0$1801a8c0@Stile> In-Reply-To: <20051209162735.574015bc@frankie.konav201.local>
next in thread | previous in thread | raw e-mail | index | archive | help
> > -----Original Message----- > From: Loren M. Lang [mailto:lorenl@alzatex.com] > Sent: Friday, December 09, 2005 9:06 AM > To: Peter Giessel > Cc: Keith Bottner; 'FreeBSD Questions' > Subject: Re: Detect hardware changes > > On Thu, Dec 08, 2005 at 12:02:25PM -0900, Peter Giessel wrote: > > On 12/8/2005 11:51, Keith Bottner seems to have typed: > > > skc0@pci2:9:0: class=0x020000 card=0x00241737 chip=0x10321737 > > > rev=0x10 hdr=0x00 > > > vendor = 'Linksys' > > > device = 'EG1032 Gigabit Ethernet' > > > class = network > > > subclass = ethernet > > > > Looks like this should be supported using the nge driver. > > No, actually the sk driver, look at the first line of pciconfig > output. ifconfig -a should list a network card called skc0 which you > just need to configure. If all you need is dhcp then just run > dhclient skc0. Add the device to rc.conf for it to work on boot. > Use man rc.conf for help or copy the line for the xl0 network card you > already have. > > > _______________________________________________ > > freebsd-questions@freebsd.org mailing list > > http://lists.freebsd.org/mailman/listinfo/freebsd-questions > > To unsubscribe, send any mail to > "freebsd-questions-unsubscribe@freebsd.org" > > > > ipconfig -a doesn't show the skc0 device which I believe is my > ultimate problem. Can I infer from your earlier message that this > means the sk module is not being loaded or is not available? How can I > check to see if the loadable module is installed? > > Thanks, > > Keith > > Hello Keith > > skc0 is the controller. You should see sk0 in ifconfig -a. > > Can you please show us the output of ifconfig -a and rc.conf. > > Thank you > Robert Ifconfig does not show skc0 but here is the output for completeness: xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 options=9<RXCSUM,VLAN_MTU> inet 192.168.1.217 netmask 0xffffff00 broadcast 192.168.1.255 inet6 fe80::2b0:d0ff:fe16:3d30%xl0 prefixlen 64 scopeid 0x1 ether 00:b0:d0:16:3d:30 media: Ethernet autoselect (100baseTX <full-duplex>) status: active lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2 And rc.conf is: defaultrouter="192.168.1.1" hostname="gsdev.bltmobile.com" ifconfig_xl0="inet 192.168.1.217 netmask 255.255.255.0" ifconfig_skc0="inet 10.0.130.204 netmask 255.255.255.0" linux_enable="YES" moused_enable="YES" sshd_enable="YES" usbd_enable="YES" postgresql_enable="YES" Anything else that I can send that will help? Keith
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?014901c5ff28$2174bac0$1801a8c0>