From owner-freebsd-hackers Sun Jan 7 05:41:56 1996 Return-Path: owner-hackers Received: (from root@localhost) by freefall.freebsd.org (8.7.3/8.7.3) id FAA10407 for hackers-outgoing; Sun, 7 Jan 1996 05:41:56 -0800 (PST) Received: from whome.planix.com (whome.planix.com [204.29.161.33]) by freefall.freebsd.org (8.7.3/8.7.3) with SMTP id FAA10402 for ; Sun, 7 Jan 1996 05:41:51 -0800 (PST) Received: by whome.planix.com (Smail3.1.28.1 #38) id m0tYvLx-000743C; Sun, 7 Jan 96 08:41 EST Received: by mail.kcis.com (KCIS.COM-5) id IAA04590; Sun Jan 7 08:45:19 1996 Date: Sun Jan 7 08:45:19 1996 From: jerry@kcis.com (Jerry T. Kendall) Organization: Kendall Communications & Information Services, Toronto, Canada Posted-Date: Sun, 7 Jan 1996 08:45:19 -0500 (EST) Received-Date: Sun, 7 Jan 1996 08:45:19 -0500 (EST) Message-Id: <199601071345.IAA04590.antares.kcis.com@kcis.com> To: hackers@freebsd.org Subject: diskless systems setup Sender: owner-hackers@freebsd.org Precedence: bulk DISKLESS SYSTEMS: A how to guide by Jerry Kendall(jerry@kcis.com) With the help of some 'friends' on the FreeBSD-hackers list, I have been able to create a diskless X terminal... The creation of the X terminal required first creating a diskless system with minimal utilities mounted via NFS. These same steps were used to create 2 seperate diskless systems. The first is 'altair.kcis.com'. A diskless X terminal that I run on my old 386DX-40. It has a 340Meg hard disk but, I did not want to change it. So, it boots from 'antares.kcis.com' across a ethernet. The second system is at work. It is a 486DX2-66. I setup a diskless FreeBSD(complete) that uses no local disk. The server in that case is a Sun 670MP running SunOS 4.1.3. The same setup configuration was needed for both. NOTE: I am sure that there is stuff that needs to be added to this. Please send me any comments.... Creating the boot floppy(On the diskless system) Since the network boot loaders will not work with some of the TSR's and such that MS-DOS uses, it is best to create a dedicated boot floppy OR, if you can, create an MS-DOS menu that will(via the config.sys/autoexec.bat files) ask what configuration to load when the system starts. The later is the method that I use and it works great. My MS-DOS(6.x) menu is below. ---- config.sys ---- [menu] menuitem=normal, normal menuitem=unix, unix [normal] .... normal config.sys stuff ... [unix] ---- ---- autoexec.bat ---- @ECHO OFF goto %config% :normal ... normal autoexec.bat stuff ... goto end :unix cd \netboot nb8390.com :end ---- Getting the network boot programs(On the server) Compile the 'net-boot' programs that are located in /usr/src/sys/i386/boot/netboot. You should read the comments at the top of the makefile. Adjust as required. !!!! make a backup of the original in case it gets fobar'd !!! When the build is done, there should be 2 MS-DOS executables, 'nb8390.com' and 'nb3c509.com'. One of these two programs will be what you need to run on the diskless server. It will load the kernel from the boot server. At this point, put both programs on the MS-DOS boot floppy created earlier. Determine which program to run(On the diskless system) If you know the chipset that your ethernet adapter uses, this is easy. If you have the NS8390 chipset, or a NS8390 based chipset, use NB8390.COM. If you have a 3Com 509 based chipset, use the NB3C509.COM boot program. If you are not sure which you have, try using one, if it says 'No adapter found', try the other. Beyond that, you are pretty much on your own. Booting across the network Boot the diskless system with out any config.sys/autoexec.bat files. try running the boot program for your ethernet adapter. My ethernet adapter is running in WD8013 16bit mode so I run NB8390.COM C:> cd \netboot C:> nb8390 Boot from Network (Y/N) ? Y BOOTP/TFTP/NFS bootstrap loader ESC for menu Searching for adapter.. WD8013EBT base 0x0300, memory 0x000D8000, addr 00:40:01:43:26:66 Searching for server.. At this point, my diskless system is trying to find a machine to act as a boot server. Make note of the addr line above, you will need this number later. Reset the diskless system and modify your config.sys and autoexec.bat files to do these steps automatically for you. Perhaps in a menu. If you had to run 'nb3c509.com' instead of 'nb8390.com' the output is the same as above. If you got 'No adapter found' at the 'Searching for adapter..' message, verify that you did indeed set the compile time defines in the makefile correctly. Allowing systems to boot across the network(On the server) Make sure the /etc/inetd.conf file has entries for tftp and bootps. Mine are listed below: ---- /etc/inetd.conf ---- tftp dgram udp wait nobody /usr/libexec/tftpd tftpd # # Additions by who ever you are bootps dgram udp wait root /usr/libexec/bootpd bootpd /etc/bootptab ---- If you have to change the /etc/inetd.conf file, send a HUP signal to inetd. To do this, get the process ID of inetd with 'ps -ax | grep inetd | grep -v grep'. Once you have it, send it a HUP signal. Do this by 'kill -HUP '. This will force inetd to re-read its config file. Did you remember to note the 'addr' line from the output of the boot loader on the diskless system???? Guess what, here is where you need it. Add an entry to /etc/bootptab(maybe creating the file). It should be laid out identical to this: altair:\ :ht=ether:\ :ha=004001432666:\ :sm=255.255.255.0:\ :hn:\ :ds=199.246.76.1:\ :ip=199.246.76.2:\ :gw=199.246.76.1:\ :vm=rfc1048: The lines are as follows: 'altair' the diskless systems name without the domain name. 'ht=ether' the hardware type of 'ethernet'. 'ha=004001432666' the hardware address(the number noted above). 'sm=255.255.255.0' the subnet mask. 'hn' tells server to send client's hostname to the client. 'ds=199.246.76.1' tells the client who the domain server is. 'ip=199.246.76.2' tells the client what it's IP address is. 'gw=199.246.76.1' tells the client what the default gateway is. 'vm=...' just leave it there... NOTE: ****** Be sure to setup the IP addresses correctly, the addresses above are my own...... Create the directory '/tftpboot' on the server it will contain the configuration files for the diskless systems that the server will serve. These files will be named 'cfg.' where is the IP address of the diskless system. The config file for 'altair' is /tftpboot/cfg.199.246.76.2. The contents is: ---- /tftpboot/cfg.199.246.76.2 ---- rootfs 199.246.76.1:/DiskLess/rootfs/altair hostname altair.kcis.com ---- The line 'hostname altair.kcis.com' simply tells the diskless system what it fully qualified domain name is. The line 'rootfs 199.246.76.1:/DiskLess/rootfs/altair' tells the diskless system where it NFS mountable root filesystem is located. NOTE:!!!!! The NFS mounted root filesystem will be mounted READ ONLY. The hierarchy for the diskless system can be re-mounted allowing read-write operations if required. I use my spare 386DX-40 as a dedicated X terminal... The hierarchy for 'altair' is: / /bin /etc /tmp /sbin /dev /dev/fd /usr /var /var/run The actual list of files is: -r-xr-xr-x 1 root wheel 779984 Dec 11 23:44 ./kernel -r-xr-xr-x 1 root bin 299008 Dec 12 00:22 ./bin/sh -rw-r--r-- 1 root wheel 499 Dec 15 15:54 ./etc/rc -rw-r--r-- 1 root wheel 1411 Dec 11 23:19 ./etc/ttys -rw-r--r-- 1 root wheel 157 Dec 15 15:42 ./etc/hosts -rw-r--r-- 1 root bin 1569 Dec 15 15:26 ./etc/XF86Config.altair -r-x------ 1 bin bin 151552 Jun 10 1995 ./sbin/init -r-xr-xr-x 1 bin bin 176128 Jun 10 1995 ./sbin/ifconfig -r-xr-xr-x 1 bin bin 110592 Jun 10 1995 ./sbin/mount_nfs -r-xr-xr-x 1 bin bin 135168 Jun 10 1995 ./sbin/reboot -r-xr-xr-x 1 root bin 73728 Dec 13 22:38 ./sbin/mount -r-xr-xr-x 1 root wheel 1992 Jun 10 1995 ./dev/MAKEDEV.local -r-xr-xr-x 1 root wheel 24419 Jun 10 1995 ./dev/MAKEDEV Don't forget to 'MAKEDEV all' in the 'dev' directory. My /etc/rc for 'altair' is: #!/bin/sh # PATH=/bin:/sbin export PATH # # configure the localhost /sbin/ifconfig lo0 127.0.0.1 # # configure the ethernet card /sbin/ifconfig ed0 199.246.76.2 netmask 0xffffff00 # # mount the root filesystem via NFS /sbin/mount antares:/DiskLess/rootfs/altair / # # mount the /usr filesystem via NFS /sbin/mount antares:/DiskLess/usr /usr # /usr/X11R6/bin/XF86_SVGA -query antares -xf86config /etc/XF86Config.altair > /dev/null 2>&1 # # Reboot after X exits /sbin/reboot # # We blew up.... exit 1 Any comments and ALL questions welcome.... Jerry Kendall jerry@kcis.com