Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 10 May 1999 09:34:50 +0100
From:      Richard Smith <rsmith@trltech.co.uk>
To:        Questions FreeBSD <freebsd-questions@FreeBSD.org>
Subject:   Adaptec 2920C takes 15 minutes to boot up
Message-ID:  <37369A2A.7755B9EB@trltech.co.uk>

next in thread | raw e-mail | index | archive | help
This is a multi-part message in MIME format.
--------------15BC426757A446FFCD1C8B46
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit

I recently introduced a colleague to FreeBSD. He is now running 3.1R and
working his way through Greg's good book :)

An annoyance that I have been unable to help him with concerns the aha0
controller which appears to be reset several times, over a period of
some 15 minutes, before the system eventually runs just fine.

The SCSI controller is an Adaptec 2920C with (I think) three devices
attached to it. Does anyone understand what's going on, and is there a
switch or option that can be used to optimize the boot up procedure.

I have attached as much of dmesg as he sent to me, there appears to be a
4 minute pause around each BUS DEVICE RESET statement.

Thanks for any help,
Richard.
--------------15BC426757A446FFCD1C8B46
Content-Type: text/plain; charset=us-ascii; name="dmesg"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline; filename="dmesg"

00
wdc1 at 0x170-0x177 irq 15 on isa
wdc1: unit 0 (wd2): <QUANTUM FIREBALL_TM3200A>
wd2: 3067MB (6281856 sectors), 6232 cyls, 16 heads, 63 S/T, 512 B/S
wd2: ATA INQUIRE valid = 0003, dmamword = 0407, apio = 0003, udma = 0000
wdc1: unit 1 (wd3): <QUANTUM Bigfoot TX12.0AT>
wd3: 11497MB (23547888 sectors), 23361 cyls, 16 heads, 63 S/T, 512 B/S
wd3: ATA INQUIRE valid = 0007, dmamword = 0007, apio = 0003, udma = 0407
wt0 not found at 0x300
mcd0: timeout getting status
mcd0 not found at 0x300
matcdc0 not found at 0x230
scd0 not found at 0x230
ppc: parallel port found at 0x378
ppc0: 0x87 - 0x0 0x0 0x2 0x50 0x44 0x0 0x0 0x0 0x0 0xc 0xa 0xc 0x28 0xab 0x0 0x0 0x0 0x0 0x0 0x0 0x7 0x0 0x1e 0xfc 0xff 0x22 0xde 0xfe 0xbe 0x23 0x25 0x43 0x60 
ppc0:ppc0: W83757 compatible mode
ppc0: SPP
ppc0 at 0x378 irq 7 on isa
ppc0: Winbond chipset (NIBBLE-only) in COMPATIBLE mode
nlpt0: <generic printer> on ppbus 0
nlpt0: Interrupt-driven port
ppi0: <generic parallel i/o> on ppbus 0
plip: irq 7
plip0: <PLIP network interface> on ppbus 0
ie0: unknown board_id: f000
ie0 not found at 0x300
ep0 not found at 0x300
ex0 not found
le0 not found at 0x300
lnc0 not found at 0x280
ze0 not found at 0x300
zp0 not found at 0x300
cs0 not found at 0x300
adv0 not found at 0x330
bt0: Failed Status Reg Test - fe
bt0: Failed Status Reg Test - ff
bt0: Failed Status Reg Test - ff
bt0: Failed Status Reg Test - ff
bt0: Failed Status Reg Test - ff
bt0: Failed Status Reg Test - ff
bt0 not found at 0x134
aha0: status reg test failed fe
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0 not found at 0x134
vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3b0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xf00b8000 size:32k gran:32k, buf:0x0 size:0k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
npx0 on motherboard
npx0: INT 16 interface
i586_bzero() bandwidth = 351370344 bytes/sec
bzero() bandwidth = 532481363 bytes/sec
apm0: disabled, not probed.
imasks: bio c008c040, tty c007009a, net c007009a
BIOS Geometries:
 0:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
 1:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
 2:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
 3:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
 4:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
 5:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
 6:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
 7:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors
 0 accounted for
Device configuration finished.
new masks: bio c008c040, tty c007009a, net c007009a
Waiting 15 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
ahc0: Selection Timeout on A:4. 1 SCBs aborted
ahc0: Selection Timeout on A:5. 1 SCBs aborted
ahc0: Selection Timeout on A:6. 1 SCBs aborted
(probe0:ahc0:0:0:0): INQUIRY. CDB: 12 1 80 0 ff 0 
(probe0:ahc0:0:0:0): ILLEGAL REQUEST asc:24,0
(probe0:ahc0:0:0:0): Invalid field in CDB
(probe1:ahc0:0:1:0): INQUIRY. CDB: 12 1 80 0 ff 0 
(probe1:ahc0:0:1:0): ILLEGAL REQUEST asc:24,0
(probe1:ahc0:0:1:0): Invalid field in CDB
(probe2:ahc0:0:2:0): INQUIRY. CDB: 12 1 80 0 ff 0 
(probahc0: target 0 synchronous at 10.0MHz, offset = 0x8
e2:ahc0:0:2:0): ILLEGAL REQUEST asc:24,0
(probe2:ahc0:0:2:0): Invalid field in CDB
ahc0: target 1 synchronous at 10.0MHz, offset = 0xf
(probe3:ahc0:0:3:0): INQUIRY. CDB: 12 1 80 0 ff 0 
(probe3:ahc0:0:3:0): NOT READY csi:1,0,0,0 asc:3a,0
(probe3:ahc0:0:3:0): Medium not present
ahc0: target 3 synchronous at 10.0MHz, offset = 0xf
ahc0:A:3: no active SCB for reconnecting target - issuing BUS DEVICE RESET
SAVED_TCL == 0x30, ARG_1 == 0xff, SEQ_FLAGS == 0x0
(probe0:ahc0:0:3:2): SCB 0x3 - timed out in datain phase, SEQADDR == 0x151
(probe0:ahc0:0:3:2): BDR message in message buffer
(probe0:ahc0:0:3:2): SCB 0x3 - timed out in datain phase, SEQADDR == 0x151
(probe0:ahc0:0:3:2): no longer in timeout, status = 34b
ahc0: target 0 using asynchronous transfers
ahc0: target 1 using asynchronous transfers
ahc0: target 3 using asynchronous transfers
ahc0: Issued Channel A Bus Reset. 1 SCBs aborted
ahc0: target 3 synchronous at 10.0MHz, offset = 0xf
ahc0:A:3: no active SCB for reconnecting target - issuing BUS DEVICE RESET
SAVED_TCL == 0x30, ARG_1 == 0xff, SEQ_FLAGS == 0x0
(probe0:ahc0:0:3:4): SCB 0x3 - timed out in datain phase, SEQADDR == 0x151
(probe0:ahc0:0:3:4): BDR message in message buffer
(probe0:ahc0:0:3:4): SCB 0x3 - timed out in datain phase, SEQADDR == 0x151
(probe0:ahc0:0:3:4): no longer in timeout, status = 34b
ahc0: target 3 using asynchronous transfers
ahc0: Issued Channel A Bus Reset. 1 SCBs aborted
ahc0: target 3 synchronous at 10.0MHz, offset = 0xf
ahc0:A:3: no active SCB for reconnecting target - issuing BUS DEVICE RESET
SAVED_TCL == 0x30, ARG_1 == 0xff, SEQ_FLAGS == 0x0
(probe0:ahc0:0:3:6): SCB 0x3 - timed out in datain phase, SEQADDR == 0x151
(probe0:ahc0:0:3:6): BDR message in message buffer
(probe0:ahc0:0:3:6): SCB 0x3 - timed out in datain phase, SEQADDR == 0x151
(probe0:ahc0:0:3:6): no longer in timeout, status = 34b
ahc0: target 3 using asynchronous transfers
ahc0: Issued Channel A Bus Reset. 1 SCBs aborted
ahc0: target 3 synchronous at 10.0MHz, offset = 0xf
pass0 at ahc0 bus 0 target 0 lun 0
pass0: <PLEXTOR CD-R   PX-R820T 1.03> Removable CD-ROM SCSI-2 device 
pass0: 3.300MB/s transfers
pass1 at ahc0 bus 0 target 1 lun 0
pass1: <PIONEER DVD-ROM DVD-U02 1.06> Removable CD-ROM SCSI-2 device 
pass1: 3.300MB/s transfers
pass2 at ahc0 bus 0 target 2 lun 0
pass2: <YAMAHA CRW4260 1.0q> Removable CD-ROM SCSI-2 device 
pass2: 3.300MB/s transfers
pass3 at ahc0 bus 0 target 3 lun 0
pass3: <SAF CD-R2006 1.1a> Removable CD-ROM SCSI-2 device 
pass3: 10.0MB/s transfers (10.0MHz, offset 15)
Considering MFS root f/s.
No MFS image available as root f/s.
Considering FFS root f/s.
changing root device to wd1s1a
ahc0: target 0 synchronous at 10.0MHz, offset = 0x8
wd1s1: type 0xa5, start 63, end = 4127759, size 4127697 : OK
ahc0: target 1 synchronous at 10.0MHz, offset = 0xf
cd0 at ahc0 bus 0 target 0 lun 0
cd0: <PLEXTOR CD-R   PX-R820T 1.03> Removable CD-ROM SCSI-2 device 
cd0: 10.0MB/s transfers (10.0MHz, offset 8)
cd0: cd present [340672 x 2048 byte records]
(cd1:ahc0:0:1:0): READ CD RECORDED CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 
(cd1:ahc0:0:1:0): NOT READY asc:3a,0
(cd1:ahc0:0:1:0): Medium not present
cd1 at ahc0 bus 0 target 1 lun 0
cd1: <PIONEER DVD-ROM DVD-U02 1.06> Removable CD-ROM SCSI-2 device 
cd1: 10.0MB/s transfers (10.0MHz, offset 15)
cd1: Attempt to query device size failed: NOT READY, Medium not present
(cd2:ahc0:0:2:0): READ CD RECORDED CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 
(cd2:ahc0:0:2:0): NOT READY asc:3a,1
(cd2:ahc0:0:2:0): Medium not present - tray closed
cd2 at ahc0 bus 0 target 2 lun 0
cd2: <YAMAHA CRW4260 1.0q> Removable CD-ROM SCSI-2 device 
cd2: 3.300MB/s transfers
cd2: Attempt to query device size failed: NOT READY, Medium not present - tray closed
(cd3:ahc0:0:3:0): READ CD RECORDED CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 
(cd3:ahc0:0:3:0): NOT READY csi:1,0,0,0 asc:3a,0
(cd3:ahc0:0:3:0): Medium not present
cd3 at ahc0 bus 0 target 3 lun 0
cd3: <SAF CD-R2006 1.1a> Removable CD-ROM SCSI-2 device 
cd3: 10.0MB/s transfers (10.0MHz, offset 15)
cd3: Attempt to query device size failed: NOT READY, Medium not present

--------------15BC426757A446FFCD1C8B46--



To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?37369A2A.7755B9EB>