Date: Mon, 12 Mar 2018 07:59:50 +0000 From: bugzilla-noreply@freebsd.org To: freebsd-wireless@FreeBSD.org Subject: [Bug 226549] lagg failover with re0 and ath0 does not operate by switching back Message-ID: <bug-226549-21060@https.bugs.freebsd.org/bugzilla/>
next in thread | raw e-mail | index | archive | help
https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=3D226549 Bug ID: 226549 Summary: lagg failover with re0 and ath0 does not operate by switching back Product: Base System Version: CURRENT Hardware: amd64 OS: Any Status: New Severity: Affects Only Me Priority: --- Component: wireless Assignee: freebsd-wireless@FreeBSD.org Reporter: ish@amail.plala.or.jp I use lagg on 12.0-CURRENT r330627 as follows. % ifconfig re0: flags=3D8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=3D80088<VLAN_MTU,VLAN_HWCSUM,LINKSTATE> ether 9c:30:5b:78:a4:a7 hwaddr 8c:ec:4b:55:60:68 nd6 options=3D29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: Ethernet autoselect (1000baseT <full-duplex>) status: active lo0: flags=3D8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 options=3D600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6> inet6 ::1 prefixlen 128=20 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2=20 inet 127.0.0.1 netmask 0xff000000=20 nd6 options=3D21<PERFORMNUD,AUTO_LINKLOCAL> groups: lo=20 wlan0: flags=3D8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 15= 00 ether 9c:30:5b:78:a4:a7 nd6 options=3D29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: IEEE 802.11 Wireless Ethernet DS/1Mbps mode 11ng status: associated ssid XXXXXX channel 4 (2427 MHz 11g ht/20) bssid XX:XX:XX:XX:XX:XX regdomain JAPAN country JP indoor ecm authmode WPA2/802.11i privacy ON deftxkey UNDEF AES-CCM 3:128-bit txpower 23 bmiss 7 scanvalid 60 protmode CTS ampdulimit 64k ampdudensity 4 shortgi -stbctx stbcrx -ldpc wme burst roaming MANUAL groups: wlan=20 lagg0: flags=3D8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 15= 00 ether 9c:30:5b:78:a4:a7 inet 192.168.1.5 netmask 0xffffff00 broadcast 192.168.1.255=20 inet6 fe80::5%lagg0 prefixlen 64 scopeid 0x4=20 inet6 XXXX:XXXX:XXXX:XXXX::5 prefixlen 64 autoconf=20 nd6 options=3D3<PERFORMNUD,ACCEPT_RTADV> media: Ethernet autoselect status: active groups: lagg=20 laggproto failover lagghash l2,l3,l4 laggport: re0 flags=3D5<MASTER,ACTIVE> laggport: wlan0 flags=3D0<> When I disconnect the lan cable, it automatically switches and communicates. when I connect lan cable again, the output of ifconfig is the same as above= but it is not communicates. I can recover by 'ifconfig re0 down && ifconfig re0 up'. % dmesg|grep ath [ath_hal] loaded ath0: <Qualcomm Atheros AR9565> mem 0xdf000000-0xdf07ffff at device 0.0 on = pci3 ath0: WB335 2-ANT card detected ath0: Bluetooth Antenna Diversity card detected ath0: [HT] enabling HT modes ath0: [HT] enabling short-GI in 20MHz mode ath0: [HT] 1 stream STBC receive enabled ath0: [HT] 1 RX streams; 1 TX streams ath0: QCA9565 mac 704.2 RF5110 phy 769.7 ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000 % dmesg | grep re0 re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem 0xdf104000-0xdf104fff,0xdf100000-0xdf103fff at device 0.0= on pci2 re0: Using 1 MSI-X message re0: turning off MSI enable bit. re0: ASPM disabled re0: Chip rev. 0x54000000 re0: MAC rev. 0x00100000 miibus0: <MII bus> on re0 re0: Using defaults for TSO: 65518/35/2048 re0: Ethernet address: 8c:ec:4b:55:60:68 re0: netmap queues/slots: TX 1/256, RX 1/256 --=20 You are receiving this mail because: You are the assignee for the bug.=
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?bug-226549-21060>