Date: Wed, 12 Aug 1998 17:07:45 -0300 From: "Javier Kohan" <jkohan@adan.fceia.unr.edu.ar> To: <aic7xxx@FreeBSD.ORG> Subject: HP LD Pro: Problems detecting devices. Message-ID: <043a01bdc62c$dfe7e820$6302a8c0@pepa.pm.rosario.gov.ar>
next in thread | raw e-mail | index | archive | help
I'm trying to run Linux in a Hewlett Packard LD Pro, with:
PPro 200 (one)
128Mb RAM
9G HD (SCSI ID = 0 )
CDROM ( ID = 5 )
DAT ( ID = 3 )
HP OEM EtherExpress 10/100 network card
3C905 TX network card.
At boot time, randomly detects, or not, the SCSI units, that is, sometimes
detects all of then, somtimes only the HD ( I Initially had the HD at ID 1,
and then, most of times it was not detected ).
I tried 2.0.34 and 2.1.112 with identical results. I also tried configuring
the kernel to wait 15s after resetting the host.
The diagnostic software tells me that the server is all right, and
previously the server had NT 4.0 and worked fine, and if I can't get Linux
running, my boss will ask me to install NT again.
Please, save me ! :)
Below is a dmesg of one of the few times that it detected all the devices:
Thanks in advance.
============
Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
pcibios_init : BIOS32 Service Directory structure at 0x000fd8e0
pcibios_init : BIOS32 Service Directory entry at 0xf5d57
pcibios_init : PCI BIOS revision 2.10 entry at 0xf6694
Probing PCI hardware.
Calibrating delay loop.. ok - 199.07 BogoMIPS
Memory: 127944k/131072k available (664k kernel code, 384k reserved, 2080k
data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: ICMP, UDP, TCP
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 2.0.34 (root@brutus) (gcc version 2.7.2.3) #2 Tue Aug 11
21:31:34 ART 1998
Starting kswapd v 1.4.2.2
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
PS/2 auxiliary pointing device detected -- driver installed.
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
(scsi0) <Adaptec AIC-7880 Ultra SCSI host adapter> found at PCI 10/0
(scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
(scsi0) BIOS disabled, IO Port 0xf800, IRQ 15
(scsi0) IO Memory at 0xfedff000, MMAP Memory at 0x8805000
(scsi0) Resetting channel
(scsi0) Downloading sequencer code... 413 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.0.19/3.2.4
<Adaptec AIC-7880 Ultra SCSI host adapter>
scsi : 1 host.
(scsi0:0:-1:-1) Scanning channel for devices.
(scsi0:0:0:0) Using wide (16 bit) transfers.
(scsi0:0:0:0) Synchronous at 20.0MHz, offset 8.
Vendor: HP Model: 9.10GB A 80-1220 Rev:
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: HP Model: C1533A Rev: A612
Type: Sequential-Access ANSI SCSI revision: 02
Detected scsi tape st0 at scsi0, channel 0, id 3, lun 0
Vendor: TOSHIBA Model: CD-ROM XM-5401TA Rev: 3115
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 5, lun 0
scsi : detected 1 SCSI tape 1 SCSI cdrom 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17773524 [8678 MB] [8.7
GB]
eepro100.c:v0.99B 4/7/98 Donald Becker linux-eepro100@cesdis.gsfc.nasa.gov
eth0: OEM i82557/i82558 10/100 Ethernet at 0xece0, 00:60:B0:67:25:CD, IRQ
10.
Board assembly 673610-001, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x49caa8d6).
Receiver lock-up workaround activated.
eepro100.c:v0.99B 4/7/98 Donald Becker linux-eepro100@cesdis.gsfc.nasa.gov
eth1: 3Com 3c905 Boomerang 100baseTx at 0xec40, 00:60:08:9d:80:f6, IRQ 11
8K word-wide RAM 3:5 Rx:Tx split, autoselect/NWay Autonegotiation
interface.
MII transceiver found at address 24, status 7869.
Enabling bus-master transmits and whole-frame receives.
3c59x.c:v0.99E 5/12/98 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
Partition check:
sda: sda1 sda2 sda3 sda4
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 130748k swap-space (priority -1)
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe aic7xxx" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?043a01bdc62c$dfe7e820$6302a8c0>