Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 24 Feb 2006 12:59:25 +0100
From:      Bernd Walter <ticso@cicely12.cicely.de>
To:        Marius Strobl <marius@alchemy.franken.de>
Cc:        ticso@cicely.de, freebsd-sparc64@freebsd.org
Subject:   Re: E150 support
Message-ID:  <20060224115925.GB3342@cicely12.cicely.de>
In-Reply-To: <20060221203111.GH3342@cicely12.cicely.de>
References:  <20060221191248.GD3342@cicely12.cicely.de> <20060221211309.A9340@newtrinity.zeist.de> <20060221203111.GH3342@cicely12.cicely.de>

next in thread | previous in thread | raw e-mail | index | archive | help
On Tue, Feb 21, 2006 at 09:31:12PM +0100, Bernd Walter wrote:
> On Tue, Feb 21, 2006 at 09:13:10PM +0100, Marius Strobl wrote:
> > On Tue, Feb 21, 2006 at 08:12:48PM +0100, Bernd Walter wrote:
> > > Has anyone an overview about what might be required to support
> > > an E150?
> > > 
> > 
> > AFAICT they use the same motherboard as Ultra 1 so they should
> > work just fine with 6.1-BETA2 modulo the on-board floppy and
> > printer port controllers as well as framebuffer cards. Releases
> > prior to 6.1-BETA2 don't support the on-board Ethernet and the
> > 6.0-RELEASE and prior loader can't boot from devices attached
> > to the on-board SCSI controller though.
> 
> I've heared that with the Ultra1 motherboard as well, but wasn't
> shure since only the Ultra1e is listed as supported.
> So there is even hope for the onboard SCSI and Ethernet.
> Not that they are very importent.
> Once I have my fingers on real hardware I will keep you informed.

With 6.2-Beta2 ISO1:
ok boot cdrom /boot/loader    
Boot device: /sbus/espdma@e,8400000/esp@e,8800000/sd@6,0:f  File and args: /boot/loader
 
>> FreeBSD/sparc64 boot block
   Boot path:   /sbus@1f,0/espdma@e,8400000/esp@e,8800000/sd@6,0:f
   Boot loader: /boot/loader
Consoles: Open Firmware console  
Boot path set to /sbus@1f,0/espdma@e,8400000/esp@e,8800000/sd@6,0:a

FreeBSD/sparc64 bootstrap loader, Revision 1.0
(root@s-dallas.cse.buffalo.edu, Thu Feb 16 22:49:16 UTC 2006)
bootpath="/sbus@1f,0/espdma@e,8400000/esp@e,8800000/sd@6,0:a"
Loading /boot/defaults/loader.conf 
/boot/kernel/kernel data=0x47d908+0x5bbe8 syms=[0x8+0x63648+0x8+0x537a1]
\
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...               
nothing to autoload yet.
jumping to kernel entry at 0xc0050000.
stray vector interrupt 2033
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 6.1-BETA2 #0: Fri Feb 17 12:44:14 UTC 2006
    root@s-dallas.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "tick" frequency 166980265 Hz quality 1000
real memory  = 268435456 (256 MB)
avail memory = 241795072 (230 MB)
cpu0: Sun Microsystems UltraSparc-I Processor (166.98 MHz CPU)
nexus0: <Open Firmware Nexus device>
sbus0: <U2S UPA-SBus bridge> on nexus0
sbus0: clock 25.000 MHz
sbus dvma: DVMA map: 0xfc000000 to 0xffffffff
sbus0: [FAST]
sbus0: [FAST]
initializing counter-timer
Timecounter "counter-timer" frequency 1000000 Hz quality 100
auxio0: <Sun Auxiliary I/O> mem 0x1900000 on sbus0
sbus0: <SUNW,CS4231> mem 0xc000000-0xc0001ff irq 2020 type unknown (no driver attached)
sbus0: <flashprom> mem 0-0x7ffff,0x1380000-0x13fffff type unknown (no driver attached)
sbus0: <SUNW,fdtwo> mem 0x1400000-0x1400007 irq 2025 type block (no driver attached)
eeprom0: <EEPROM/clock> mem 0x1200000-0x1201fff on sbus0
eeprom0: model mk48t59
eeprom0: hostid 808595a9
puc0: <Zilog Z8530 dual channel SCC> mem 0x1100000-0x1100003 irq 2024 on sbus0
uart0: <z8530, channel A> on puc0
uart0: console (9600,n,8,1)
uart1: <z8530, channel B> on puc0
puc1: <Zilog Z8530 dual channel SCC> mem 0x1000000-0x1000003 irq 2024 on sbus0
uart2: <z8530, channel A> on puc1
uart2: keyboard (1200,n,8,1)
uart2: keyboard not present
uart3: <z8530, channel B> on puc1
sbus0: <sc> mem 0x1300000-0x1300007 type unknown (no driver attached)
sbus0: <SUNW,pll> mem 0x1304000-0x1304002 type unknown (no driver attached)
dma0: <espdma> mem 0x8400000-0x840000f on sbus0
dma0: DMA rev. 2
esp0: <Sun ESP SCSI/Sun FAS Fast-SCSI> mem 0x8800000-0x880003f irq 2016 on dma0
esp0: FAS100A, 40MHz, SCSI ID 7
dma1: <ledma> mem 0x8400010-0x840002f on sbus0
dma1: DMA rev. 2
le0: <LANCE Ethernet> mem 0x8c00000-0x8c00003 irq 2017 on dma1
le0: 8 receive buffers, 2 transmit buffers
le0: Ethernet address: 08:00:20:85:95:a9
sbus0: <SUNW,bpp> mem 0xc800000-0xc80001b irq 2018 type unknown (no driver attached)
hme0: <Sun HME 10/100 Ethernet> mem 0x8c00000-0x8c00107,0x8c02000-0x8c03fff,0x8c04000-0x8c05fff,0x8c06000-0x8c07fff,0x8c07000-0x8c0701f irq 1988 on sbus0
miibus0: <MII bus> on hme0
nsphy0: <DP83840 10/100 media interface> on miibus0
nsphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
hme0: Ethernet address: 08:00:20:85:95:a9
esp1: <Sun FAS366 Fast-Wide SCSI> mem 0x8800000-0x880000f,0x8810000-0x881003f irq 1987 on sbus0
esp1: FAS366/HME, 40MHz, SCSI ID 7
nexus0: <syscons>, type (unknown) (no driver attached)
Timecounters tick every 1.000 msec
Waiting 5 seconds for SCSI devices to settle
md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xc05902f0
cd0 at esp0 bus 0 target 6 lun 0
cd0: <TOSHIBA XM5701TASUN12XCD 0997> Removable CD-ROM SCSI-2 device 
cd0: 10.000MB/s transfers (10.000MHz, offset 8)
cd0: cd present [1109088 x 512 byte records]
da2 at esp1 bus 0 target 4 lun 0
da2: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device 
da2: 20.000MB/s transfers (10.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da2: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
da1 at esp1 bus 0 target 3 lun 0
da1: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device 
da1: 20.000MB/s transfers (10.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da1: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
da0 at esp0 bus 0 target 0 lun 0
da0: <IBM DCAS32160SUN2.1G S65A> Fixed Direct Access SCSI-2 device 
da0: 10.000MB/s transfers (10.000MHz, offset 15)
da0: 2063MB (4226725 512 byte sectors: 255H 63S/T 263C)
da3 at esp1 bus 0 target 10 lun 0
da3: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device 
da3: 20.000MB/s transfers (10.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da3: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
da4 at esp1 bus 0 target 11 lun 0
da4: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device 
da4: 20.000MB/s transfers (10.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da4: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
da5 at esp1 bus 0 target 12 lun 0
da5: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device 
da5: 20.000MB/s transfers (10.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da5: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
Trying to mount root from ufs:/dev/md0
/stand/sysinstall running as init on serial console

These are the predefined terminal types available to
sysinstall when running stand-alone.  Please choose the
closest match for your particular terminal.

1 ...................... Standard ANSI terminal.
2 ...................... VT100 or compatible terminal.
3 ...................... FreeBSD system console (color).
4 ...................... FreeBSD system console (monochrome).

5 ...................... xterm terminal emulator.

Your choice: (1-5) 


Looks promissing :)

-- 
B.Walter                   BWCT                http://www.bwct.de
bernd@bwct.de                                  info@bwct.de




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20060224115925.GB3342>