Date: Tue, 11 Jun 1996 14:58:30 +0000 From: Matt Thomas <matt@lkg.dec.com> To: freebsd-mobile@freebsd.org Subject: DEPCM-BA on Digital HiNote Ultrix CT450 Message-ID: <199606111458.OAA26786@whydos.lkg.dec.com>
next in thread | raw e-mail | index | archive | help
Works using the following entry:
# Digital DEPCM-BA Ethernet
card "DIGITAL" "DEPCM-XX"
config default "ed0" any 0x10
ether 0xff0 00:00:e8
insert /etc/pccard_ether $device
remove /etc/pccard_ether_remove $device
# pccardc
Configuration data for card in slot 1
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
000: dc 03 ff
Common memory device information:
Device number 1, type Function specific, WPS = ON
Speed = 100nS, Memory block size = 32Kb, 1 units
Tuple #2, code = 0x17 (Attribute memory descriptor), length = 3
000: 53 01 ff
Attribute memory device information:
Device number 1, type FLASH EEPROM, WPS = OFF
Speed = 150nS, Memory block size = 2Kb, 1 units
Tuple #3, code = 0x21 (Functional ID), length = 2
000: 06 03
Network/LAN adapter - POST initialize - Card has ROM
Tuple #4, code = 0x15 (Version 1 info), length = 39
000: 04 01 44 49 47 49 54 41 4c 00 44 45 50 43 4d 2d
010: 58 58 00 31 39 39 34 30 35 33 31 00 41 30 31 2e
020: 30 30 2e 30 31 00 ff
Version = 4.1, Manuf = [DIGITAL],card vers = [DEPCM-XX]
Addit. info = [19940531],[A01.00.01]
Tuple #5, code = 0x1a (Configuration map), length = 5
000: 01 08 00 01 01
Reg len = 2, config register addr = 0x100, last config = 0x8
Registers: X-------
Tuple #6, code = 0x1b (Configuration entry), length = 21
000: c1 81 1d 3f 55 4d 5d 06 86 46 26 fc 24 ca 60 00
010: 03 1f 30 38 9e
Config index = 0x1(default)
Interface byte = 0x81 (I/O) wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Continuous supply current: 1 x 100mA
Max current average over 1 second: 1 x 100mA, ext = 0x46
Max current average over 10 ms: 2 x 100mA
Wait scale Speed = 1.5 x 10 us
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x300 block length = 0x20
IRQ modes: Level
IRQs: 3 4 5 9 10 11 12 15
Tuple #7, code = 0x1b (Configuration entry), length = 7
000: 02 08 ca 60 20 03 1f
Config index = 0x2
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x320 block length = 0x20
Tuple #8, code = 0x1b (Configuration entry), length = 7
000: 03 08 ca 60 40 03 1f
Config index = 0x3
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x340 block length = 0x20
Tuple #9, code = 0x1b (Configuration entry), length = 7
000: 04 08 ca 60 60 03 1f
Config index = 0x4
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x360 block length = 0x20
Tuple #10, code = 0x1b (Configuration entry), length = 7
000: 05 08 ca 60 00 02 1f
Config index = 0x5
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x200 block length = 0x20
Tuple #11, code = 0xff (Terminator), length = 0
--
Matt Thomas Internet: matt@3am-software.com
3am Software Foundry WWW URL: http://www.3am-software.com/bio/matt.html
Westford, MA Disclaimer: I disavow all knowledge of this message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199606111458.OAA26786>