Date: Sat, 15 Jun 2002 12:48:30 +0300 From: "Mihail Balikov" <misho@interbgc.com> To: "Luigi Rizzo" <rizzo@icir.org> Cc: <ipfw@freebsd.org> Subject: Re: New ipfw code available Message-ID: <001601c21451$ce2f2d60$eee209d9@interbgc.com> References: <20020608201909.A41807@iguana.icir.org>
next in thread | previous in thread | raw e-mail | index | archive | help
how about adding simple checksum of rules , something like incrementing counter on every IP_FW_FLUSH, IP_FW_ADD, IP_FW_DEL regards, misho ----- Original Message ----- From: "Luigi Rizzo" <rizzo@icir.org> To: <ipfw@freebsd.org> Sent: Sunday, June 09, 2002 6:19 AM Subject: New ipfw code available > [Bcc to -current because it is relevant there as well -- sorry for the > crosspost] > > > Hi, > over the past 2-3 weeks I have done an extensive rewrite of the > ipfw code (userland + kernel) in an attempt to make it faster and > more flexible. > > The idea (which I discussed a few times on the mailing lists) was > to replace the current ipfw rules (macroinstructions) with a set > of microinstructions, each of them performing a single operation > such as matching an address, or a port range, or a protocol flag, > etc. -- much in the spirit of BPF and derivatives -- and to let > the userland front-end compile ipfw(8) commands into an appropriate > set of microinstructions. > > There are several advantages in using this technique: first of all, > instructions are typically shorter and faster, because the former > code had to check for the presence of all the possible options in > a rule, whereas the new one can simply do just the things that are > required -- e.g. an instruction like > > allow ip from 1.2.3.0/24 to any > > translates to a couple of microinstructions (whose complete > implementation is below the instructions themselves): > > O_IP_DST > if (((ipfw_insn_ip *)cmd)->addr.s_addr == > (dst_ip.s_addr & ((ipfw_insn_ip *)cmd)->mask.s_addr)) > goto cmd_match; > goto cmd_fail; > > O_ACCEPT: > retval = 0; /* accept */ > goto accept; > > > But there is a lot more -- the instruction set is easily extensible, > and without backward compatibility problems. Furthermore, you can > build (and I have already implemented them) more complex rules by > assembling microinstructions with OR and NOT operands. I.e. you can write > something like: > > pipe 10 tcp from 1.2.3.4 or 1.2.3.7 or not 1.2.3.0/28 21-25,1024-4095 \ > to any in recv ed0 or recv fxp1 or recv dc0 uid 35 or uid 50 > > You get the idea... > > I have a fairly complete version of the above code at the moment, > which is only missing a small set of functionalities > (ip/tcp flags matching, "log" and fixing hooks to the stateful > code). However the glue to implement all the missing pieces is > already there, it is just a matter of adding a few lines of code > and testing things. > Other than that, the code is meant to be fully compatible with the > old syntax so you will not have to rewrite your existing rulesets. > > I have put a preliminary snapshot of this code (for CURRENT) at > > http://info.iet.unipi.it/~luigi/ipfw5.20020609.tgz > > It replaces the following files from a recent (2002/05/14) version of -current. > > sys/netinet/ip_dummynet.c > sys/netinet/ip_fw.c > sys/netinet/ip_fw.h > sbin/ipfw/ipfw.c > > I would be very grateful if someone could have a look at the > code, maybe give it a try, and see e.g. how it compiles your > typical ruleset and whether the new extensions can make your > ipfw rulesets simpler. > > Feedback welcome, both on the architecture and on the implementation. > > NOTE: if people wonder why I did not use BPF and reinvented the wheel: > the keyword is "backward compatiblity" -- i thought it was a bit too > complex to compile the existent ipfw syntax into BPF, especially because > BPF at least as far as i know does not handle UIDs, and GIDs and > interface matches and different "actions" than match or not match, > so i would have had to extend the code anyways, at which point i > thought I could as well write my own microinstruction set... > > cheers > luigi > -----------------------------------+------------------------------------- > Luigi RIZZO, luigi@iet.unipi.it . Dip. di Ing. dell'Informazione > http://www.iet.unipi.it/~luigi/ . Universita` di Pisa > TEL/FAX: +39-050-568.533/522 . via Diotisalvi 2, 56126 PISA (Italy) > Mobile +39-347-0373137 > -----------------------------------+------------------------------------- > to > > thanks > luigi > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-ipfw" in the body of the message > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-ipfw" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?001601c21451$ce2f2d60$eee209d9>