Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 22 Feb 2012 13:36:20 +0100
From:      zulu <zulu@openvps.biz>
To:        "freebsd-usb@freebsd.org" <freebsd-usb@freebsd.org>
Subject:   fantec db 229 U3
Message-ID:  <1329914180.4f44e14401943@gpo.cellcontainer.com>

next in thread | raw e-mail | index | archive | help


Hi,

I can't use my external HDD attached to my la=
ptop. The drive enclosure
is a Fantec db 229 U3 case (USB3). My lapt=
op has only USB2 ports.

I have tested this with both FreeBSD =
9.0 RELEASE and FreeBSD 9 STABLE
- same issues.

Tested wi=
th linux too on the same hardware and it is working fine. The
manual=
 which came with the drive enclosure states Linux, Mac OSX and
Windo=
ws support.

Can someone please point me to the right directio=
n? I have included
some dumps bellow.

Many than=
ks,

Peter

dmesg:

usb_alloc_device: set =
address 2 failed (USB_ERR_STALLED, ignored)

usbd_setup_device=
_desc: getting device descriptor at addr 2 failed,
USB_ERR_STALL=
ED
usbd_req_re_enumerate: addr=3D2, set address failed! (USB_ERR_STALL=
ED,
ignored)
usbd_setup_device_desc: getting device descriptor=
 at addr 2 failed,
USB_ERR_STALLED
usbd_req_re_enumerate: ad=
dr=3D2, set address failed! (USB_ERR_STALLED,
ignored)
usbd_setu=
p_device_desc: getting device descriptor at addr 2 failed,
USB_ERR_S=
TALLED
ugen1.2:  at usbus1 (disconnected)

uhub_reattach_por=
t: could not allocate new device

usbconfig output:

u=
gen0.1:  at usbus0, cfg=3D0 md=3DHOST spd=3DFULL (12Mbps) pwr=3DSAVE=

ugen1.1:  at usbus1, cfg=3D0 md=3DHOST spd=3DFULL (12Mbps) pwr=3DSA=
VE
ugen2.1:  at usbus2, cfg=3D0 md=3DHOST spd=3DHIGH (480Mbps) pwr=
=3DSAVE
ugen3.1:  at usbus3, cfg=3D0 md=3DHOST spd=3DFULL (12Mbps) p=
wr=3DSAVE
ugen4.1:  at usbus4, cfg=3D0 md=3DHOST spd=3DFULL (12Mbps) =
pwr=3DSAVE
ugen5.1:  at usbus5, cfg=3D0 md=3DHOST spd=3DFULL (12Mbps=
) pwr=3DSAVE
ugen6.1:  at usbus6, cfg=3D0 md=3DHOST spd=3DHIGH (480M=
bps) pwr=3DSAVE
ugen0.2:  at usbus0, cfg=3D0 md=3DHOST spd=3DFULL (1=
2Mbps) pwr=3DON
ugen0.3:  at usbus0, cfg=3D0 md=3DHOST spd=3DFULL (1=
2Mbps) pwr=3DON
ugen4.2:  at usbus4, cfg=3D0 md=3DHOST spd=3DFULL (1=
2Mbps) pwr=3DON

pciconf:

uhci2@pci0:0:29:0:class=3D0=
x0c0300 card=3D0x20aa17aa chip=3D0x28308086
rev=3D0x03 hdr=3D0x00=

vendor =3D 'Intel Corporation'
device =3D '82801H (ICH8 Family)=
 USB UHCI Controller'
class =3D serial bus
subclass =3D =
USB
bar [20] =3D type I/O Port, range 32, base 0x18a0, size 32, ena=
bled
uhci3@pci0:0:29:1:class=3D0x0c0300 card=3D0x20aa17aa chip=3D0x283=
18086
rev=3D0x03 hdr=3D0x00
vendor =3D 'Intel Corporation'
d=
evice =3D '82801H (ICH8 Family) USB UHCI Controller'
class =3D seria=
l bus
subclass =3D USB
bar [20] =3D type I/O Port, range 32, bas=
e 0x18c0, size 32, enabled
uhci4@pci0:0:29:2:class=3D0x0c0300 card=
=3D0x20aa17aa chip=3D0x28328086
rev=3D0x03 hdr=3D0x00
vendor =
=3D 'Intel Corporation'
device =3D '82801H (ICH8 Family) USB UHCI Co=
ntroller'
class =3D serial bus
subclass =3D USB
bar [20] =
=3D type I/O Port, range 32, base 0x18e0, size 32, enabled
ehci1@pci0:=
0:29:7:class=3D0x0c0320 card=3D0x20ab17aa chip=3D0x28368086
rev=3D0x=
03 hdr=3D0x00
vendor =3D 'Intel Corporation'
device =3D '82801H =
(ICH8 Family) USB2 EHCI Controller'
class =3D serial bus
subcla=
ss =3D USB
bar [10] =3D type Memory, range 32, base 0xfe227000, size=
 1024, enabled
cap 01[50] =3D powerspec 2 supports D0 D3 current D=
0
cap 0a[58] =3D EHCI Debug Port at offset 0xa0 in map 0x1=
4





Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1329914180.4f44e14401943>