From owner-freebsd-stable Sun Oct 15 21:10:49 2000 Delivered-To: freebsd-stable@freebsd.org Received: from uemsconcpf1.cpf.navy.mil (oban-nat-1.cpf.navy.mil [199.124.14.1]) by hub.freebsd.org (Postfix) with ESMTP id 9B38C37B66E for ; Sun, 15 Oct 2000 21:10:45 -0700 (PDT) Received: by u352-serv-1-host-269.cpf.navy.mil with Internet Mail Service (5.5.2650.21) id <467AG917>; Sun, 15 Oct 2000 18:10:39 -1000 Message-ID: From: "Kuriyama, Kent K Mr (CPF N651KK)" To: "Freebsd-Stable (E-mail)" Subject: Screen saver error message seen on 4.1.1-STABLE Date: Sun, 15 Oct 2000 18:10:36 -1000 MIME-Version: 1.0 X-Mailer: Internet Mail Service (5.5.2650.21) Content-Type: text/plain; charset="iso-8859-1" Sender: owner-freebsd-stable@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG On the CVSUP dated 10/10/00 I get the following error message: logo_saver: no suitable graphics mode module_register_init: MOD_LOAD (logo_saver, c0d48a60, 0) error 19 My rc.conf contains the line: saver="logo" These error messages did not occur in earlier snapshots of 4.1.1-STABLE. Shown below is the 'dmesg' output, I created a GENERIC kernel to remove any "customizations" as a reason for the problem. Any help would be greatly appreciated. Thanks. Kent Kuriyama SPAWAR Sys Ctr San Diego D424, CINCPACFLT N671KK kuriyakk@cpf.navy.mil, 808-471-4125 -----Original Message----- Copyright (c) 1992-2000 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.1.1-STABLE #0: Sun Oct 15 17:29:14 HST 2000 root@somehost:/usr/src/sys/compile/GENERIC Timecounter "i8254" frequency 1193182 Hz CPU: Pentium Pro (199.43-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x617 Stepping = 7 Features=0xfbff real memory = 67108864 (65536K bytes) avail memory = 61190144 (59756K bytes) Preloaded elf kernel "kernel" at 0xc041d000. Pentium Pro MTRR support enabled md0: Malloc disk npx0: on motherboard npx0: INT 16 interface pcib0: on motherboard pci0: on pcib0 Correcting Natoma config for non-SMP Correcting Natoma config for non-SMP isab0: at device 13.0 on pci0 isa0: on isab0 atapci0: port 0xffa0-0xffaf at device 13.1 on pci0 atapci0: Busmastering DMA not enabled ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pcib1: at device 14.0 on pci0 pci1: on pcib1 ahc0: port 0xdc00-0xdcff mem 0xf9fff000-0xf9ffffff irq 10 at device 11.0 on pci1 aic7860: Single Channel A, SCSI Id=7, 3/255 SCBs pci0: at 16.0 irq 0 xl0: <3Com 3c900-COMBO Etherlink XL> port 0xccc0-0xccff irq 11 at device 17.0 on pci0 xl0: Ethernet address: 00:60:97:61:83:aa xl0: selecting 10baseT transceiver, half duplex fdc0: at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: at port 0x60,0x64 on isa0 vga0: at port 0x3b0-0x3cf iomem 0xa0000-0xbffff on isa0 sc0: at flags 0x100 on isa0 sc0: VGA (mono) <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A ppc0: at port 0x378-0x37f irq 7 on isa0 ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold plip0: on ppbus0 lpt0: on ppbus0 lpt0: Interrupt-driven port ppi0: on ppbus0 ad0: 3020MB [6136/16/63] at ata0-master using BIOSPIO acd0: CDROM at ata1-master using PIO3 Waiting 15 seconds for SCSI devices to settle Mounting root from ufs:/dev/ad0s1a IP packet filtering initialized, divert disabled, rule-based forwarding disabled, default to deny, logging disabled logo_saver: no suitable graphics mode module_register_init: MOD_LOAD (logo_saver, c0d48a60, 0) error 19 To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-stable" in the body of the message